Search NASA⌕ Search

Engineering topics

Sindir, M. M.

Publications and source records attributed to Sindir, M. M..

7 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Development of code evaluation criteria for assessing predictive capability and performance

Computational Fluid Dynamics (CFD), because of its unique ability to predict complex three-dimensional flows, is being applied with increasing frequency in the aerospace industry. Currently, no consistent code validation procedure is applied within the industry. Such a procedure is needed to increase confidence in CFD and reduce risk in the use of these codes as a design and analysis tool. This final contract report defines classifications for three levels of code validation, directly relating the use of CFD codes to the engineering design cycle. Evaluation criteria by which codes are measured and classified are recommended and discussed. Criteria for selecting experimental data against which CFD results can be compared are outlined. A four phase CFD code validation procedure is described in detail. Finally, the code validation procedure is demonstrated through application of the REACT CFD code to a series of cases culminating in a code to data comparison on the Space Shuttle Main Engine High Pressure Fuel Turbopump Impeller.

Lin, Shyi-Jang↗
NASA NTRS1992

Development of CFD code evaluation criteria and a procedure for assessing predictive capability and performance

Careful validation of computational fluid dynamic (CFD) codes is essential if they are to be used as engineering design tools. Validation must be carried out in a systematic manner to ensure that all code aspects as they apply to the application of interest are understood and, to the greatest extent possible, quantified. A study is being conducted in which a general code validation procedure is defined and demonstrated. A four phase validation procedure is defined in which a series of validation test cases are computed and compared with available analytical solutions and test data. The procedure is demonstrated using the REACT CFD code to compute validation cases for each of the four phases. For phase four, the application of interest, the Space Shuttle Main Engine high pressure fuel turbopump impeller flow field, is computed.

Lin, S. J.↗
NASA NTRS1986

Analysis of Leakage Flows in Turbomachinery

Navier-Stokes calculations predict leakage flow in high-pressure fuel pump. Accurate calculation of internal turbomachinery flow dynamics helps spot possible failure modes and establishes coupling between cyclic loading and structural dynamics. Approach also useful in analyzing two-and quasi-three-dimensional leakage flows in other turbomachinery components.

Sindir, M. M.↗
NASA NTRS1984

Turbulent transport models for scramjet flowfields

Turbulence modeling approaches were examined from the standpoint of their capability to predict the complex flowfield features observed in scramjet combustions. Thus, for example, the accuracy of each turbulence model, with respect to the prediction of recirculating flows, was examined. It was observed that for large diameter ratio axisymmetric sudden expansion flows, a choice of turbulence model was not critical because of the domination of their flowfields by pressure forces. For low diameter ratio axisymmetric sudden expansions and planar backward-facing steps flows, where turbulent shear stresses are of greater significance, the algebraic Reynolds stress approach, modified to increase its sensitivity to streamline curvature, was found to provide the best results. Results of the study also showed that strongly swirling flows provide a stringent test of turbulence model assumptions. Thus, although flows with very high swirl are not of great practical interest, they are useful for turbulence model development. Finally, it was also noted that numerical flowfields solution techniques have a strong interrelation with turbulence models, particularly with the turbulent transport models which involve source-dominated transport equations.

Sindir, M. M.↗
NASA NTRS1983

Effects of expansion ratio on the calculation of parallel-walled backward-facing step flows - Comparison of four models of turbulence

This paper presents a numerical study of the effects of expansion ratio on two-dimensional separating and reattaching flows in plane backward-facing step geometries with parallel walls. Closure of the Reynolds equations was achieved by four different turbulence models: k-epsilon, 'modified' k-epsilon, algebraic stress, and 'modified' algebraic stress models. The k-epsilon model relates the Reynolds stresses to the mean rate of strain through the definition of an isotropic turbulent viscosity. The more advanced algebraic stress model calculates the stresses from implicit algebraic relationships containing the stresses themselves, the mean rate of strain, and the turbulent kinetic energy and its dissipation rate. 'Modified' versions of the models employ a new dissipation rate equation whose production term was made more sensitive to streamwise curvature effects. A new nonequilibrium wall function treatment proposed by Chieng and Launder (1980) was also incorporated into each model.

Sindir, M. M.↗
NASA NTRS1982

Assessment of turbulent models for scramjet flowfields

The behavior of several turbulence models applied to the prediction of scramjet combustor flows is described. These models include the basic two equation model, the multiple dissipation length scale variant of the two equation model, and the algebraic stress model (ASM). Predictions were made of planar backward facing step flows and axisymmetric sudden expansion flows using each of these approaches. The formulation of each of these models are discussed, and the application of the different approaches to supersonic flows is described. A modified version of the ASM is found to provide the best prediction of the planar backward facing step flow in the region near the recirculation zone, while the basic ASM provides the best results downstream of the recirculation. Aspects of the interaction of numerica modeling and turbulences modeling as they affect the assessment of turbulence models are discussed.

Sindir, M. M.↗