Search NASA⌕ Search

Engineering topics

Singh, Onkar

Publications and source records attributed to Singh, Onkar.

Synthesis and characterization of biobased copolyesters based on pentanediol: (2) Poly(pentylene adipate–co–terephthalate)

Traditionally, most flexible food packaging is made of linear low-density polyethylene (LLDPE) which cannot easily be recycled, nor will it degrade in a reasonable timescale. In this work, a biobased biodegradable polyester alternative was investigated as a possible replacement for LLDPE. High molecular weight poly (pentylene adipate-co-terephthalate) with a 40/60 adipic acid/terephthalic acid mole ratio was synthesized using direct esterification and polycondensation. Glycerol and hexane-1,2,5,6-tetrol were added as branching agents to better match the structure of the LLDPE which in turn might help the ability of these materials in film-blowing. Thermal, mechanical, and rheological properties of the copolyesters were thoroughly investigated. All copolyesters had a weight-average molecular weight of over 140,000 g/mol, which is necessary for proper rheology, and were thermally stable up to 350°C. Here, the addition of branching agents led to a slight decrease in crystallinity, d-spacing, melting temperature, enthalpy of melting, stress at break, and elongation at break. However, an increase in Young's modulus and complex viscosity at high frequency were observed compared to PPeAT60 without branching agent added. Although the improved crystallinity and mechanical properties of the copolyesters made them viable for film-blowing, the slow crystallization rate creates a major challenge.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Synthesis and characterization of biobased copolyesters based on pentanediol: (1) Poly(pentylene dodecanoate–co–furandicarboxylate)

A series of biobased aliphatic-aromatic copolyesters, poly(pentylene dodecanoate-co-furandicarboxylates) (PPeDFs) were synthesized via an esterification and polycondensation melt process. The copolyesters were characterized using gel permeation chromatography, Fourier transform infrared spectroscopy, 1 H NMR spectroscopy, differential scanning calorimetry, thermogravimetric analysis, wide angle x-ray scattering, and tensile testing. The thermal transition behavior was strongly dependent on composition, with the melting and glass transition temperatures reaching a minimum at approximately equimolar ratio of D to F. All copolyesters were stable below 300°C with their R 600 (the weight of material remaining at 600°C) values increasing with F fraction. PPeD to PPeDF30 (e.g., mole ratio D/F = 7:3) show sharp PPeD crystalline reflections only while broad PPeF reflections are shown in PPeF and PPeDF90. PPeDF40 to PPeDF80 showed both crystal structures. The fractional crystallinity for the PPeD was much higher than PPeF and the fractional crystallinity of the copolymers showed a minimum at D/F ratios closer to the latter. Here, the stress at break and modulus both exhibited maxima at D/F ratios that were either high or low, but somewhat surprisingly a strong maximum in percent elongation at break of over 600% occurs at PPeDF40. For this composition, a typical plastic behavior curve was found including a yield point, high elongation at break, and strain hardening.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Overview of the interactive task in BioCreative V

Fully automated text mining (TM) systems promote efficient literature searching, retrieval, and review but are not sufficient to produce ready-to-consume curated documents. These systems are not meant to replace biocurators, but instead to assist them in one or more literature curation steps. To do so, the user interface is an important aspect that needs to be considered for tool adoption. The BioCreative Interactive task (IAT) is a track designed for exploring user-system interactions, promoting development of useful TM tools, and providing a communication channel between the biocuration and the TM communities. In BioCreative V, the IAT track followed a format similar to previous interactive tracks, where the utility and usability of TM tools, as well as the generation of use cases, have been the focal points. The proposed curation tasks are user-centric and formally evaluated by biocurators. In BioCreative V IAT, seven TM systems and 43 biocurators participated. Two levels of user participation were offered to broaden curator involvement and obtain more feedback on usability aspects. The full level participation involved training on the system, curation of a set of documents with and without TM assistance, tracking of time-on-task, and completion of a user survey. Here, the partial level participation was designed to focus on usability aspects of the interface and not the performance per se. In this case, biocurators navigated the system by performing pre-designed tasks and then were asked whether they were able to achieve the task and the level of difficulty in completing the task. In this manuscript, we describe the development of the interactive task, from planning to execution and discuss major findings for the systems tested.

96 KNOWLEDGE MANAGEMENT AND PRESERVATION↗

Acetone sensor based on zinc oxide hexagonal tubes

In this work hexagonal tubes of zinc oxide have been synthesized by co-precipitation method. For structural, morphological, elemental and optical analysis synthesized powders were characterized by using x-ray diffraction, field emission scanning microscope, EDX, UV-visible and FTIR techniques. For acetone sensing thick films of zinc oxide have been deposited on alumina substrate. The fabricated sensors exhibited maximum sensing response towards acetone vapour at an optimum operating temperature of 400°C.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Effect of reaction temperature on crystallite size and sensing response of chromium oxide nanoparticles

Graphical abstract: Sensing response towards 250 ppm ethanol for the samples synthesized at different reaction temperatures at different operating temperatures. Highlights: ► Effect of reaction temperature on particle size of Cr{sub 2}O{sub 3}. ► No catalyst has been incorporated to enhance the response of the material. ► Synthesis of Cr{sub 2}O{sub 3} nanoparticles. -- Abstract: Nanoparticles of chromium oxide have been synthesized following a precipitation technique at reaction temperatures 5, 27 and 65 °C. Synthesized powders were characterized using X-ray diffraction, transmission electron microscope and Brunauer–Emmett–Teller techniques to carry out structural and morphological analysis. The reaction temperature has been found to be playing a crucial role in controlling particle size. It has been observed that Cr{sub 2}O{sub 3} nanoparticles synthesized at 27 °C were smaller as compared to those synthesized at 5 and 65 °C. Chromium oxide samples thus prepared were deposited as thick films on alumina substrates to act as gas sensors and their sensing response to ethanol vapour was investigated at different operable temperatures. It has been observed that all the sensors exhibited optimum response at 250 °C. The investigations revealed that sensing response of Cr{sub 2}O{sub 3} nanoparticles synthesized at 27 °C was exceptionally higher than that of Cr{sub 2}O{sub 3} nanoparticles synthesized at 5 and 65 °C.

36 MATERIALS SCIENCE↗

Sensing behaviour of nanosized zinc-tin composite oxide towards liquefied petroleum gas and ethanol

A chemical route has been used to synthesize composite oxides of zinc and tin. An ammonia solution was added to equal amounts of zinc and tin chloride solutions of same molarities to obtain precipitates. Three portions of these precipitates were annealed at 400, 600 and 800 {sup o}C, respectively. Results of X-ray diffraction and transmission electron microscopy clearly depicted coexistence of phases of nano-sized SnO{sub 2}, ZnO, Zn{sub 2}SnO{sub 4} and ZnSnO{sub 3}. The effect of annealing on structure, morphology and sensing has been observed as well. It has been observed that annealing promoted growth of Zn{sub 2}SnO{sub 4} and ZnSnO{sub 3} at the expense of zinc. The sensing response of fabricated sensors from these materials to 250 ppm LPG and ethanol has been investigated. The sensor fabricated from powder annealed at 400 {sup o}C responded better to LPG than ethanol.

36 MATERIALS SCIENCE↗