Search NASA⌕ Search

Engineering topics

Singh, Vijay

Publications and source records attributed to Singh, Vijay.

17 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Transgenic Sugarcane–Oilcane: An Alternative Feedstock for the Production of Drop-in Fuel and Value-Added Bioproducts

The utilization of plants and other agricultural produce can partly offset petroleum dependency for energy requirements and can potentially provide sustainable solutions to global environmental problems. To this end, synthetic biology has shown great potential in developing transgenic bioenergy grasses such as sugarcane, sorghum, miscanthus, and energy cane that hyperaccumulate energy-rich lipid molecules in their vegetative tissues, such as leaves, stems, and roots. These perennial high-biomass transgenic C4 grasses are not targeted to grow on prime agricultural land and can be dedicatedly used to produce biofuels and other value-added bioproducts. Recently, sugarcane has been metabolically engineered to sequestrate carbon from juice towards biosynthesis of lipid molecules in the vegetative tissues. Transgenic sugarcane is referred to as “oilcane.” Transgenic sugarcane–oilcane has improved energy density due to an elevated lipid content in the vegetative tissues. Transgenic bioenergy crops cater to both cellulosic sugars and vegetative lipids, hence resulting in higher biofuel yield (biodiesel/renewable diesel and bioethanol) per unit area of cultivable land. In this book chapter, the genetic engineering of sugarcane and its bioprocessing are discussed to illustrate its development and use as an alternative feedstock for the production of biofuels (bio-jet fuel, biodiesel, and bioethanol) and value-added bioproducts.

Maitra, Shraddha↗
DOE OSTI2024

Engineering and evolution of Yarrowia lipolytica for producing lipids from lignocellulosic hydrolysates

Yarrowia lipolytica, an oleaginous yeast, shows promise for industrial fermentation due to its robust acetyl-CoA flux and well-developed genetic engineering tools. However, its lack of an active xylose metabolism restricts the conversion of cellulosic sugars to valuable products. To address this, metabolic engineering, and adaptive laboratory evolution (ALE) were applied to the Y. lipolytica PO1f strain, resulting in an efficient xylose-assimilating strain (XEV). Whole-genome sequencing (WGS) of the XEV followed by reverse engineering revealed that the amplification of the heterologous oxidoreductase pathway and a mutation in the GTPase-activating protein gene (YALI0B12100g) might be the primary reasons for improved xylose assimilation in the XEV strain. When a sorghum hydrolysate was used, the XEV strain showed superior xylose consumption and lipid production compared to its parental strain (X123). This study advances our understanding of xylose metabolism in Y. lipolytica and proposes effective metabolic engineering strategies for optimizing lignocellulosic hydrolysates.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2024

Integration of plant and microbial oil processing at oilcane biorefineries for more sustainable biofuel production

Oilcane—an oil-accumulating crop engineered from sugarcane—and microbial oil have the potential to improve renewable oil production and help meet the expected demand for bioderived oleochemicals and fuels. To assess the potential synergies of processing both plant and microbial oils, the economic and environmental implications of integrating microbial oil production at oilcane and sugarcane biorefineries were characterized. Due to decreased crop yields that lead to higher simulated feedstock prices and lower biorefinery capacities, current oilcane prototypes result in higher costs and carbon intensities than microbial oil from sugarcane. To inform oilcane feedstock development, we calculated the required biomass yields (as a function of oil content) for oilcane to achieve financial parity with sugarcane. At 10 dw% oil, oilcane can sustain up to 30% less yield than sugarcane and still be more profitable in all simulated scenarios. Assuming continued improvements in microbial oil production from cane juice, achieving this target results in a minimum biodiesel selling price of 1.34 [0.90, 1.85] USD∙L –1 (presented as median [5th, 95th] percentiles), a carbon intensity of 0.51 [0.47, 0.55] kg CO 2 e L –1 , and a total biodiesel yield of 2140 [1870, 2410] L ha –1 year –1 . Compared to biofuel production from soybean, this outcome is equivalent to 3.0–3.9 as much biofuel per hectare of land and a 57%–63% reduction in carbon intensity. While only 20% of simulated scenarios fell within the market price range of biodiesel (0.45–1.11 USD∙L –1 ), if the oilcane biomass yield would improve to 25.6 DMT∙ha –1 ∙y –1 (an equivalent yield to sugarcane) 87% of evaluated scenarios would have a minimum biodiesel selling price within or below the market price range.

09 BIOMASS FUELS↗
DOE OSTI2024

Economic and environmental sustainability of bio-based HMF production and recovery from lignocellulosic biomass

5-Hydroxymethyl furfurals (HMF) is one of the versatile platform chemicals. However, green routes to produce it directly from lignocellulosic biomass are lacking. A significant amount of HMF produced during the hydrothermal valorization of lignocellulosic biomass is considered undesired and ends up in a waste stream. The study transformed the undesired byproduct into a valuable coproduct by advancing the existing biofuel production process. A detailed economic and environmental sustainability analysis of the integrated biorefinery design was performed. The evaluation showed that the biorefinery could afford a maximum feedstock purchasing price of $\$115.17$ per MT and produce HMF with a minimum selling price of $\$4.54$ per kg which is ~75% lower than the commercial price of HMF. The median global warming potential of HMF was estimated to be 3.92 kg CO 2 -eq. per kg HMF which was ~32% less than its counterpart bio-based p-xylene. Diverse coproducts produced in the biorefinery using transgenic feedstock positively impacted sustainability.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

yuyao-jia/Bio-based_HMF_coproduction

5-Hydroxymethyl furfurals (HMF) is one of the versatile platform chemicals. However, green routes to produce it directly from lignocellulosic biomass are lacking. A significant amount of HMF produced during the hydrothermal valorization of lignocellulosic biomass is considered undesired and ends up in a waste stream. The study transformed the undesired byproduct into a valuable coproduct by advancing the existing biofuel production process. A detailed economic and environmental sustainability analysis of the integrated biorefinery design was performed. The evaluation showed that the biorefinery could afford a maximum feedstock purchasing price of $115.17 per MT and produce HMF with a minimum selling price of $4.54 per kg which is ∼75% lower than the commercial price of HMF. The median global warming potential of HMF was estimated to be 3.92 kg CO2-eq. per kg HMF which was ∼32% less than its counterpart bio-based p-xylene. Diverse coproducts produced in the biorefinery using transgenic feedstock positively impacted sustainability.

Jia, Yuyao↗
DOE OSTI2024

Hydrothermal conditioning of oleaginous yeast cells to enable recovery of lipids as potential drop-in fuel precursors

Abstract Background Lipids produced using oleaginous yeast cells are an emerging feedstock to manufacture commercially valuable oleochemicals ranging from pharmaceuticals to lipid-derived biofuels. Production of biofuels using oleaginous yeast is a multistep procedure that requires yeast cultivation and harvesting, lipid recovery, and conversion of the lipids to biofuels. The quantitative recovery of the total intracellular lipid from the yeast cells is a critical step during the development of a bioprocess. Their rigid cell walls often make them resistant to lysis. The existing methods include mechanical, chemical, biological and thermochemical lysis of yeast cell walls followed by solvent extraction. In this study, an aqueous thermal pretreatment was explored as a method for lysing the cell wall of the oleaginous yeast Rhodotorula toruloides for lipid recovery. Results Hydrothermal pretreatment for 60 min at 121 °C with a dry cell weight of 7% (w/v) in the yeast slurry led to a recovery of 84.6 ± 3.2% (w/w) of the total lipids when extracted with organic solvents. The conventional sonication and acid-assisted thermal cell lysis led to a lipid recovery yield of 99.8 ± 0.03% (w/w) and 109.5 ± 1.9% (w/w), respectively. The fatty acid profiles of the hydrothermally pretreated cells and freeze-dried control were similar, suggesting that the thermal lysis of the cells did not degrade the lipids. Conclusion This work demonstrates that hydrothermal pretreatment of yeast cell slurry at 121 °C for 60 min is a robust and sustainable method for cell conditioning to extract intracellular microbial lipids for biofuel production and provides a baseline for further scale-up and process integration. Graphical abstract

09 BIOMASS FUELS↗
DOE OSTI2024

Data for Hydrothermal Conditioning of Oleaginous Yeast Cells to Enable Recovery of Lipids as Potential Drop-in Fuel Precursors

Lipids produced using oleaginous yeast cells are an emerging feedstock to manufacture commercially valuable oleochemicals ranging from pharmaceuticals to lipid-derived biofuels. Production of biofuels using oleaginous yeast is a multistep procedure that requires yeast cultivation and harvesting, lipid recovery, and conversion of the lipids to biofuels. The quantitative recovery of the total intracellular lipid from the yeast cells is a critical step during the development of a bioprocess. Their rigid cell walls often make them resistant to lysis. The existing methods include mechanical, chemical, biological and thermochemical lysis of yeast cell walls followed by solvent extraction. In this study, an aqueous thermal pretreatment was explored as a method for lysing the cell wall of the oleaginous yeast Rhodotorula toruloides for lipid recovery. Hydrothermal pretreatment for 60 min at 121 °C with a dry cell weight of 7% (w/v) in the yeast slurry led to a recovery of 84.6 ± 3.2% (w/w) of the total lipids when extracted with organic solvents. The conventional sonication and acid-assisted thermal cell lysis led to a lipid recovery yield of 99.8 ± 0.03% (w/w) and 109.5 ± 1.9% (w/w), respectively. The fatty acid profiles of the hydrothermally pretreated cells and freeze-dried control were similar, suggesting that the thermal lysis of the cells did not degrade the lipids. This work demonstrates that hydrothermal pretreatment of yeast cell slurry at 121 °C for 60 min is a robust and sustainable method for cell conditioning to extract intracellular microbial lipids for biofuel production and provides a baseline for further scale-up and process integration.

Conversion↗
DOE OSTI2024

Sustainable strategies to achieve industrial ethanol titers from different bioenergy feedstocks: scale-up approach for better ethanol yield

Hydrothermal pretreatment is a promising approach to lignocellulosic biomass processing for enzymatic hydrolysis and high-yield bioethanol fermentation, as it reduces downstream inhibitor content and the amount of toxic byproducts generated. In this paper, the ethanol yield and productivity of an engineered xylose-fermenting strain of Saccharomyces cerevisiae were tested on lignocellulosic hydrolysates produced with varying citrate buffer concentration, solid loading, supplemental nitrogen source, and feedstock of origin, and a semi-integrated bioprocess which integrates enzymatic hydrolysis and bioethanol fermentation was developed. The greatest ethanol yields (g p /g s ) of 0.490 ± 0.008, 0.460 ± 0.001, 0.420 ± 0.002 and 0.410 ± 0.002 were obtained from bioenergy sorghum (BES), Miscanthus × giganteus (MG), energy cane (EC), and oilcane (OC), respectively. In addition, an equivalent of 291 L, 253.54 L, 257.8 L, and 260.3 L of bioethanol were produced per ton of BES, MG, EC, and OC, respectively, by using urea as a nitrogen source in a bioreactor.

09 BIOMASS FUELS↗
DOE OSTI2024

Rapid and high-throughput determination of sorghum ( Sorghum bicolor ) biomass composition using near infrared spectroscopy and chemometrics

Compositional characterization of biomass is vital for the biofuel industry. Traditional wet chemistry-based methods for analyzing biomass composition are laborious, time-consuming, and require extensive use of chemical reagents as well as highly skilled personnel. In this study, near-infrared (NIR) spectroscopy was used to quickly assess the composition of above-ground vegetative biomass from 113 diverse, photoperiod-sensitive, biomass-type sorghum (Sorghum bicolor) accessions cultivated under field conditions in Central Illinois. Biomass samples were analyzed using NIR spectra collected in the spectral range of 867–2536 nm, with their chemical compositions determined following the National Renewable Energy Laboratory (NREL) protocol. Advanced spectral pre-treatment and band selection techniques were utilized to develop calibration models using partial least squares regression (PLSR). The models’ effectiveness was assessed through cross-validation and independent data tests. The predictions for moisture, ash, extractives, glucan, xylan, acid-soluble lignin (ASL), acid-insoluble lignin (AIL), and total lignin were accurate and reliable, demonstrating the capability of NIR spectroscopy to provide rapid and precise characterization of sorghum biomass. The results demonstrated that NIR spectroscopy is an efficient tool for rapidly characterizing sorghum biomass, making it a sustainable option for screening desirable feedstock for biofuel or bioproduct production.

09 BIOMASS FUELS↗
DOE OSTI2024

Data for Rapid and High-Throughput Determination of Sorghum ( Sorghum bicolor ) Biomass Composition using Near Infrared Spectroscopy and Chemometrics

Compositional characterization of biomass is vital for the biofuel industry. Traditional wet chemistry-based methods for analyzing biomass composition are laborious, time-consuming, and require extensive use of chemical reagents as well as highly skilled personnel. In this study, near-infrared (NIR) spectroscopy was used to quickly assess the composition of above-ground vegetative biomass from 113 diverse, photoperiod-sensitive, biomass-type sorghum ( Sorghum bicolor ) accessions cultivated under field conditions in Central Illinois. Biomass samples were analyzed using NIR spectra collected in the spectral range of 867–2536 nm, with their chemical compositions determined following the National Renewable Energy Laboratory (NREL) protocol. Advanced spectral pre-treatment and band selection techniques were utilized to develop calibration models using partial least squares regression (PLSR). The models’ effectiveness was assessed through cross-validation and independent data tests. The predictions for moisture, ash, extractives, glucan, xylan, acid-soluble lignin (ASL), acid-insoluble lignin (AIL), and total lignin were accurate and reliable, demonstrating the capability of NIR spectroscopy to provide rapid and precise characterization of sorghum biomass. The results demonstrated that NIR spectroscopy is an efficient tool for rapidly characterizing sorghum biomass, making it a sustainable option for screening desirable feedstock for biofuel or bioproduct production.

Biomass Analytics↗
DOE OSTI2024

Economic and environmental bottlenecks in the industrial‐scale production of lipid‐derived biofuels from oleaginous yeasts: A review of the current trends and future prospects

Abstract Concerns about climate change and the reliance on fossil fuel reserves have motivated researchers to identify new renewable sources of energy. Biomass holds the potential to replace fossil‐derived products with biofuels and bio‐based chemicals. Plant‐derived lipids are promising sources of biofuels; however, the production of plant oil often leads to the release of massive amounts of carbon dioxide due to deforestation and land‐use change. The production of biofuels via plant oils (such as soybean) also competes with food production and in turn, impacts biodiversity. To mitigate these issues, the production of lipids from oleaginous yeasts could be an excellent alternative by incorporating these microbes into biorefineries utilizing agricultural or forest residues. Eventually, these microbial lipids could be potential sources for producing lipid‐derived biofuels. However, the current conventional methods for the production and recovery of lipids from oleaginous microbes suffer from economic and ecological challenges that affect its industrial‐scale expansion. This review highlights the major economic and environmental bottlenecks for the production of lipid‐derived biofuels from oleaginous yeasts. It also provides perspectives on the strategies that could be adapted on economic and ecological fronts to assist the expansion of the production of microbial lipid‐derived biofuels at an industrial scale.

Agriculture↗
DOE OSTI2024

Process strategies for recovery of sugars, lipids, and lignin from oilcane bagasse using natural deep eutectic solvents (NADES)

Sugarcane is being enhanced as a bioenergy crop by engineering it to accumulate and store lipids along with polymeric sugars in vegetative tissues. However, there is no existing process that allows for processing this new crop to recover both lipid and cellulosic sugars from the oilcane bagasse. Therefore, a comprehensive investi- gation of two pretreatment methods—natural deep eutectic solvents (NADES) and chemical-free hydrothermal pretreatment (HT) was conducted to judge their suitability for recovering fermentable sugars, lipids, and lignin from bagasse. Two NADES, i.e., choline chloride: lactic acid (ChCl:LA) and betaine: lactic acid (BT:LA) were prepared using a 1:2 M ratio and were evaluated for pretreatment of oilcane bagasse at 10, 20, and 50 % (w/w) solids, followed by enzymatic hydrolysis at 10 % (w/w) solids. Notably, ChCl:LA NADES treatment at 10 % (w/ w) solids at 140 °C for 2 h, solubilized 78.8 % of lignin and 80.4 % of hemicellulose and allowed 82.7 % enzymatic conversion of glucans to glucose. In contrast, HT pretreatment removed approximately 87.6 % of the hemicellulose and provided an enzymatic glucose yield of 69.7 %. Furthermore, ChCl:LA operated at 50 % solids loading the enriched lipids 2.6-fold (9.2 wt%) in recovered solids compared to HT (6.4 %) and BT:LA (5.1 %) pretreatment processes. NMR-HSQC and GPC analysis showed that ChCl:LA also cleaved the most lignin β–O–4 linkages and demonstrated lower molecular weight compared to HT. As a result, this study demonstrates that NADES pretreatment is an effective green processing method for recovering lipids, sugars, and lignin from bioenergy crops at high solid loading (50 % w/w) within the context of an integrated biorefinery.

09 BIOMASS FUELS↗
DOE OSTI2024

Data for Process Strategies for Recovery of Sugars, Lipids, and Lignin from Oilcane Bagasse Using Natural Deep Eutectic Solvents (NADES)

Sugarcane is being enhanced as a bioenergy crop by engineering it to accumulate and store lipids along with polymeric sugars in vegetative tissues. However, there is no existing process that allows for processing this new crop to recover both lipid and cellulosic sugars from the oilcane bagasse. Therefore, a comprehensive investigation of two pretreatment methods—natural deep eutectic solvents (NADES) and chemical-free hydrothermal pretreatment (HT) was conducted to judge their suitability for recovering fermentable sugars, lipids, and lignin from bagasse. Two NADES, i.e., choline chloride: lactic acid (ChCl:LA) and betaine: lactic acid (BT:LA) were prepared using a 1:2 M ratio and were evaluated for pretreatment of oilcane bagasse at 10, 20, and 50 % (w/w) solids, followed by enzymatic hydrolysis at 10 % (w/w) solids. Notably, ChCl:LA NADES treatment at 10 % (w/w) solids at 140 °C for 2 h, solubilized 78.8 % of lignin and 80.4 % of hemicellulose and allowed 82.7 % enzymatic conversion of glucans to glucose. In contrast, HT pretreatment removed approximately 87.6 % of the hemicellulose and provided an enzymatic glucose yield of 69.7 %. Furthermore, ChCl:LA operated at 50 % solids loading the enriched lipids 2.6-fold (9.2 wt%) in recovered solids compared to HT (6.4 %) and BT:LA (5.1 %) pretreatment processes. NMR-HSQC and GPC analysis showed that ChCl:LA also cleaved the most lignin β–O–4 linkages and demonstrated lower molecular weight compared to HT. This study demonstrates that NADES pretreatment is an effective green processing method for recovering lipids, sugars, and lignin from bioenergy crops at high solid loading (50 % w/w) within the context of an integrated biorefinery.

Conversion↗
DOE OSTI2024

Dynamical correlations leading to site and orbital selective Mott insulator transition in hydrogen doped SmNiO 3

Electron doping induces metal -to -insulator transition (MIT) in SmNiO 3 as realized by experiments. While earlier density functional theory (DFT) studies with static correlations fell short of explaining the recent MIT observations at lower hydrogen concentrations, we present a comprehensive computational investigation employing an advanced approach. We combine DFT with dynamical mean field theory (DFT + DMFT) to efficiently analyze the insulating behavior of hydrogen -doped SmNiO 3 . In contrast to previous theoretical works, our calculations predict an insulator transition occurring at a reduced doping level of H:Ni = 0.5:1. Specifically, while the DFT + U method reveals a gap opening between p-to-d orbitals, the DMFT approach highlights a gap opening between d-to-d orbitals. Our findings uncover a selective Mott transition in site and orbital characteristics, with the Ni ions proximate to the doped hydrogen exhibiting Mott -like traits. Notably, DMFT calculations highlight a pronounced dependence on Hund's parameter J, implying the presence of Hundness in the Mott insulator. Finally, this study underscores the necessity of accounting for dynamical correlations to accurately describe the electronic structure of strongly correlated electron-doped rare-earth nickelates.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2024

Data for Sustainable Co-Production of Plant Lipids and Cellulosic Sugars from Transgenic Energycane at an Industrially Relevant Scale: A Proof of Concept for Alternative Feedstocks

Development of sustainable and scalable technologies to convert lignocellulosic biomass to biofuels is critical to achieving carbon neutrality. The potential of transgenic bioenergy crops as a renewable source of sugars and lipids has been demonstrated at bench-scale. However, scaling up these processes is important for holistic analysis. Here proof-of-concept for chemical-free hydrothermal pretreatment of transgenic energycane-oilcane line L13 at an industrially relevant scale to recover vegetative lipids along with cellulosic sugars is presented. Pilot-scale processing of 97 kg of transgenic energycane-oilcane L13 stems and high solids pretreatment of bagasse enhanced the recovery of cellulosic glucose and xylose by 5-fold as compared to untreated bagasse and helped in the enrichment of vegetative lipids in the biomass residues which allowed its recovery at the end of the bioprocess. Palmitic and oleic acids were the predominant fatty acids (FAs) extracted from stems and leaves. The processing did not affect lipid composition. The efficiency of lipid recovery from untreated biomass was 75.9% which improved to 88.7% upon pretreatment. The vegetative tissues of transgenic energycane-oilcane L13 contained 0.42 metric tons/hectare of lipids. Processing vegetative tissues yielded 0.38 metric tons/hectare of lipids. This approaches an oil yield similar to soybean (global average 0.44 metric tons/hectare) and is almost twice as high as the oil yield from sugarcane engineered to hyperaccumulate lipids (0.20 metric tons/hectare). The study suggests that further optimization by state-of-the-art metabolic engineering and biomass processing can establish transgenic bioenergy crops for commercial drop-in fuel production.

Biomass Analytics↗