Search NASA⌕ Search

Engineering topics

Sissingh, G. J.

Publications and source records attributed to Sissingh, G. J..

6 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Hingeless rotor theory and experiment on vibration reduction by periodic variation of conventional controls

The reduction of the n per rev. pitch-, roll- and vertical vibrations of an n-bladed rotor by n per rev. sinusoidal variations of the collective and cyclic controls is investigated. The numerical results presented refer to a four-bladed, 7.5-foot model and are based on frequency response tests conducted under an Army-sponsored research program. The following subjects are treated: extraction of the rotor transfer functions (.073R hub flapping and model thrust versus servo valve command, amplitude and phase), calculation of servo commands (volts) required to compensate .073R hub flapping (3P and 5P) and model thrust (4P), evaluation of the effect of the vibratory control inputs on blade loads, and theoretical prediction of the root flapbending moments generated by 0 to 5P perturbations of the feathering angle and rotor angle of attack. Five operating conditions are investigated covering advance ratios from approximately 0.2 to 0.85. The feasibility of vibration reduction by periodic variation on conventional controls is evaluated.

Sissingh, G. J.↗
NASA NTRS1974

Hingeless rotor theory and experiment on vibration reduction by periodic variation of conventional controls

A preliminary evaluation is made of the concept of vibration reduction by properly selected oscillatory collective and cyclic control applications. The investigations are based on experimental frequency response data covering advance ratios from approximately 0.2 to 0.85. Because there was no instrumentation for the measurement of the pitch and roll vibrations, these values were obtained by properly adding up the flap-bending moments at 3.3 in. Any other quantity representing pitch/roll vibrations can be compensated for in the same fashion. The calculated control inputs required for vibration reduction stay within acceptable limits. For four of the five conditions tested they are smaller than the values used for the frequency response tests. As to be expected, the compensating controls greatly affect the blade loads, i.e., torsion, flap- and chordwise bending.

Sissingh, G. J.↗
NASA NTRS1973

Experimental hingeless rotor characteristics at low advance ratio with thrust

An experimental investigation to determine the dynamic characteristics of a hingeless rotor operating at moderate to high lift was conducted on a small scale, 7.5-foot diameter, four-bladed hingeless rotor model in a 7 x 10-foot wind tunnel. The primary objective of this research program was the empirical determination of the rotor steady-state and frequency responses to swashplate and body excitations. Collective pitch was set from 0 to 20 degrees, with the setting at a particular advance ratio limited by the cyclic pitch available for hub moment trim. Advance ratio varied from 0.00 to 0.36 for blades with nondimensional first-flap frequencies at 1.15, 1.28 and 1.33 times the rotor rotation frequency. Several conditions were run with the rotor operating in the transition regime. Rotor response at high lift is shown to be generally nonlinear in this region. As a secondary objective an experimental investigation of the rotor response to 4/revolution swashplate excitations at advance ratios of 0.2 to 0.85 and at a nondimensional, first-flap modal frequency of 1.34 was also conducted, using the 7 x 10-foot wind tunnel. It is shown that 4/revolution swashplate inputs are a method for substantially reducing rotor-induced, shafttransmitted vibratory forces.

London, R. J.↗
NASA NTRS1972

Characteristics of hingeless rotors with hub moment feedback controls including experimental rotor frequency response, Volume 1

Wind tunnel tests to determine the dynamic characteristics of hingeless rotors with hub moment feedback controls and to acquire experimental hingeless rotor transfer functions are discussed. Rotor transfer functions were calculated from data acquired during open loop frequency response tests. The transfer functions are linear and present the rotor longitudinal and lateral frequency responses to collective pitch, longitudinal cyclic pitch, and lateral cyclic pitch. The theoretical analysis was based on the rigid blade flapping model coupled with appropriate control system and cyclic pitch actuator equations of motion.

Kuczynski, W. A.↗