Engineering topics
Publications and source records attributed to Sivakumar, Bhuvaneswari M..
This study systematically investigates the impact of increased upper limit voltage in the reliability and degradation of a scaled vanadium redox flow battery over long-term testing (500 cycles).
Abstract A controlled growth of two‐dimensional (2D) π‐conjugated metal‐organic frameworks (MOFs) on solid substrates can open exciting opportunities for the application of 2D MOFs as optoelectronic devices. Some factors like solvent composition and type of substrates are known to influence the properties of solution‐processed 2D MOF crystals; however, a mechanistic understanding of how interactions between solvent, substrate, and precursors affect heterogeneous nucleation has been limited. Here, it is reported that the structure of Ni‐catecholate (Ni‐CAT‐1) MOFs at a solid–liquid interface is controlled by solvent–substrate and solvent–MOF precursor interactions. Specifically, the structure of the MOF film can be controlled by varying the affinity of the solvent to the substrate. As a fraction of N , N ‐dimethylformamide (DMF) in a binary solvent mixture of water and DMF increases, the arrangement of Ni‐CAT‐1 crystals varies from vertically aligned nanorods to the graphite substrate to less ordered nanorods with the lower initial nucleation number density of Ni‐CAT‐1 crystals on the surface.
The electrochemical instability of ether-based electrolyte solutions hinders their practical applications in high-voltage Li metal batteries. To circumvent this issue, here, we propose a dilution strategy to lose the Li + /solvent interaction and use the dilute non-aqueous electrolyte solution in high-voltage lithium metal batteries. We demonstrate that in a non-polar dipropyl ether (DPE)-based electrolyte solution with lithium bis(fluorosulfonyl) imide salt, the decomposition order of solvated species can be adjusted to promote the Li + /salt-derived anion clusters decomposition over free ether solvent molecules. This selective mechanism favors the formation of a robust cathode electrolyte interphase (CEI) and a solvent-deficient electric double-layer structure at the positive electrode interface. When the DPE-based electrolyte is tested in combination with a Li metal negative electrode (50 μm thick) and a LiNi 0.8 Co 0.1 Mn 0.1 O 2 -based positive electrode (3.3 mAh/cm 2 ) in pouch cell configuration at 25 °C, a specific discharge capacity retention of about 74% after 150 cycles (0.33 and 1 mA/cm 2 charge and discharge, respectively) is obtained.
An in-depth understanding of charge transfer processes at the electrochemical interfaces is a critical knowledge gap impeding the design of energy storage materials. X-ray photoelectron spectroscopy plays an important role in analyzing electronic structures of heterogeneous interfaces, such as electrode-electrolyte interphases. Correspondingly, ex situ studies based on postmortem analysis of electrode materials using x-ray techniques are widely reported in the literature but often fail to capture intermediate and transient species, which are critical for a predictive understanding of the charge transfer process. The lack of extensive in situ/operando x-ray analysis of buried interfaces in energy storage systems can be mainly attributed to technical limitations, such as the requirement of high vacuum conditions. However, in the past decade, considerable efforts have been devoted to overcoming these technical barriers and enable investigation of the solid/solid and solid/liquid interfaces. This review catalogs some of the recent progresses and new experimental designs in the application of in situ and operando x-ray photoelectron spectroscopy toward characterizing interfacial processes and emergent properties, which can help build the design strategy for advanced batteries. The remaining challenges and future research directions are also discussed, as potential paths forward in this field.
Zinc-MnO2 based batteries have acquired attention for grid-level applications, due to impressive theoretical performance, cost effectiveness and intrinsic safety. However, there are still many challenges that remain elusive due to the complex and controversial mechanisms of operation that hinders commercialization. In this work, the detailed redox processes that occur at the cathode during Zn-MnO2 battery operation are elucidated. Using a blend of structural and electrochemical techniques, the redox pairs that occur during operation are mechanistically studied while also showcasing the true impact of the electrolyte additive (0.1 M MnSO4) in a 1 M ZnSO4 electrolyte. An electrochemical quartz-crystal microbalance (EQCM) has been leveraged to reveal the effect of zinc hydroxy sulfate salt (Zn4SO4(OH)6·nH2O) and zinc manganese oxide (ZnxMnyOz) dissolution/deposition, which are believed to be major components during discharge and charge conditions. . These results provide insight not currently available, allowing a holistic view of the electrochemical reaction mechanisms during battery operation.