Search NASA⌕ Search

Engineering topics

Sivells, James C

Publications and source records attributed to Sivells, James C.

14 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1952

Method for calculating lift distributions for unswept wings with flaps or ailerons by use of nonlinear section lift data

A method is presented which allows the use of nonlinear section lift data in the calculation of the spanwise lift distribution of unswept wings with flaps or ailerons. This method is based upon lifting line theory and is an extension to the method described in NACA rep. 865. The mathematical treatment of the discontinuity in absolute angle of attack at the end of the flap or aileron involves the use of a correction factor which accounts for the inability of a limited trigonometric series to represent adequately the spanwise lift distribution. A treatment of the apparent discontinuity in maximum section lift coefficient is also described. Simplified computing forms containing detailed examples are given for both symmetrical and asymmetrical lift distributions. A few comparisons of calculated characteristics with those obtained experimentally are also presented.

Sivells, James C↗
NASA NTRS1949

Investigation in the Langley 19-foot Pressure Tunnel of Two Wings of NACA 65-210 and 64-210 Airfoil Sections with Various Type Flaps

Report presents the results of an investigation conducted in the Langley 19-foot pressure tunnel to determine the maximum lift and stalling characteristics of two thin wings equipped with several types of flaps. Split, single slotted, and double slotted flaps were tested on one wing which had NACA 65-210 airfoil sections and split and double slotted flaps were tested on the other, which had NACA 64-210 airfoil sections. Both wings were zero sweep, an aspect ratio of 9, and a taper ratio of 0.4.

Sivells, James C↗
NASA NTRS1947

Experimental and calculated characteristics of three wings of NACA 64-210 and 65-210 airfoil sections with and without 2 degree washout

Report presents the results of an investigation conducted to determine some of the effects of airfoil section and washout on the experimental and calculated characteristics of 10-percent-thick wings. Three wings of aspect ratio 9 and ratio of root chord to tip chord 2.5 were tested. One wing had NACA 64-210 sections and 2 degree washout, the second had NACA 65-210 sections and 2 degree washout, and the third had NACA 65-210 sections and 0 degree washout. It was found that the experimental characteristics of the wings could be satisfactorily predicted from calculations based upon two-dimensional data when the airfoil contours of the wings conformed to the true airfoil sections with the same high degree of accuracy as the two-dimensional models.

AIRFOILS - NACA 65-210 - CHAR & MOMENTS LOW-DRAG↗
NASA NTRS1947

Method for calculating wing characteristics by lifting-line theory using nonlinear section lift data

A method is presented for calculating wing characteristics by lifting-line theory using nonlinear section lift data. Material from various sources is combined with some original work into the single complete method described. Multhopp's systems of multipliers are employed to obtain the induced angle of attack directly from the spanwise lift distribution. Equations are developed for obtaining these multipliers for any even number of spanwise stations, and values are tabulated for 10 stations along the semispan for asymmetrical, symmetrical, and antisymmetrical lift distributions. In order to minimize the computing time and to illustrate the procedures involved, simplified computing forms containing detailed examples are given for symmetrical lift distributions. Similar forms for asymmetrical and antisymmetrical lift distributions, although not shown, can be readily constructed in the same manner as those given. The adaptation of the method for use with linear section lift data is also illustrated. The adaptation has been found to require less computing time than most existing methods.

Sivells, James C↗
NASA NTRS1946

Jet-boundary and Plan-form Corrections for Partial-Span Models with Reflection-Plane, End-Plate, or No End-Plate in a Closed Circular Wind Tunnel

A method is presented for determining the jet-boundary and plan-form corrections necessary for application to test data for a partial-span model with a reflection plane, an end plate, or no end plate in a closed circular wind tunnel. Examples are worked out for a partial-span model with each of the three end conditions in the Langley 19-foot pressure tunnel and the corrections are applied to measured values of lift, drag, pitching-moment, rolling-moment, and yawing-moment coefficients.

Sivells, James C↗