Engineering topics

Sjoden, Glenn E.

Publications and source records attributed to Sjoden, Glenn E..

3 records

DOE OSTI2024

The production and separation of 161 Tb with high specific activity at the University of Utah

Targeted radiotherapy (TRT) is an increasingly prominent area of research in nuclear medicine, particularly in the context of treating cancerous tumors. One radionuclide of considerable interest for TRT is terbium-161 (t 1/2 = 6.95 days), which undergoes beta emission and shares similar decay properties as 177 Lu (FDA-approved as LUTATHERA® and PLUVICTO®). Besides beta emission, 161 Tb also emits a significant number of conversion and Auger electrons further enhancing its therapeutic potential. Terbium-161 can be produced using nuclear reactors through an indirect neutron capture reaction, $^{160}_{64}$Gd(n,γ) $^{161}_{64}$Gd → (3.7 min, β – ) $^{161}_{65}$Tb, from 160 Gd targets. However, a key challenge in utilizing 161 Tb for TRT lies in effectively separating target and product materials to attain high specific activity for radiolabeling. Here, we detail the production of no-carrier added 161 Tb using low flux research reactors (mean thermal (< 0.625 eV) neutron flux: 1.356 ×10 12 n • cm –2 • s –1 ) like the University of Utah TRIGA Reactor, using enriched 160 Gd 2 O 3 targets (1.5 ± 0.3 µCi of 161 Tb per mg of 160 Gd target per hour of irradiation). We also developed a separation technique based on cation exchange and extraction chromatography, suitable for mCi level irradiations with targets exceeding 200 milligrams. In a simulated full-scale irradiation, 161 Tb was successfully isolated from large mass targets using cation exchange (AG 50W-X8, with 2-hydroxyisobutyric acid at 70 mM, pH 4.75) and extraction chromatography (LN Resin, 0.5 – 0.75 M HNO 3 ) methods. Here, this resulted in high apparent molar activities of [ 161 Tb]Tb-DOTA (113 ± 3 MBq/nmol), demonstrating high purity 161 Tb relevant for potential future preclinical applications.

161Tb↗

DOE OSTI2024

Adsorption of terbium (III) on DGA and LN resins: Thermodynamics, isotherms, and kinetics

Two commercially available extraction chromatography (EXC) resins containing N,N,N’,N’-tetra-n-octyldiglycolamide (DGA Resin, Normal, 50 – 100 μm) and Bis(2-ethylhexyl) phosphate (LN Resin, 100 – 150 μm) were used as adsorbents to study fundamental adsorption properties such as thermodynamic values, equilibrium isotherms, and kinetic uptake models for terbium(III) adsorption. Weight distribution ratios (D w ) for terbium on DGA and LN resins were measured using a [ 160 Tb]Tb 3+ radiometric tracer in nitric acid as a function of acidity, temperature, initial analyte concentration, and equilibrium time. The D w values showed increasing binding affinity for DGA resin at high nitric acid concentrations and decreasing binding affinity for LN resins. Thermodynamic studies for DGA and LN resins revealed that the Gibbs free energy (ΔG) increased consistently with temperature. To model equilibrium data, increasingly higher parameter equilibrium isotherm models (Henry (1) < Langmuir, Freundlich (2) < Redlich-Peterson (3) < Fritz-Schluender (4)) were compared on their root mean squared errors (RMSE) and adjusted determination coefficients to determine the most applicable model. In all cases, the empirical four-parameter Fritz-Schluender isotherm demonstrated a superior fit. Similar comparisons for reaction-based kinetic models (Pseudo-first-order < Pseudo-second-order < Pseudo-n-order) revealed that the higher-order PNO model yielded a superior fit of kinetic data for both resins. Furthermore, in some cases, adsorption isotherms and kinetic models could also be modeled by a lower-order model with minimal change in error parameters. Weber-Morris plots revealed that two linear sections are observed for each resin, where the first linear segment is attributed to fast (film diffusion) adsorption of terbium, followed by slower intraparticle diffusion of terbium through the pores as the rate-limiting step. Based on the Weber-Morris plot, both film and intraparticle diffusion are involved in controlling the kinetic rate of adsorption for DGA and LN resins.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

DOE OSTI2021

Material Interactions in Severe Accidents – Benchmarking the MELCOR V2.2 Eutectics Model for a BWR-3 MARK-I Station Blackout: Part I – Single Case Analysis

Here in this analysis, the two material interaction models available in the MELCOR code are benchmarked for a severe accident at a BWR under representative Fukushima Daiichi boundary conditions. This part of the benchmark investigates the impact of each material interaction model on accident progression through a detailed single case analysis. It is found that the eutectics model simulation exhibits more rapid accident progression for the duration of the accident. The slower accident progression exhibited by the interactive materials model simulation, however, allows for a greater degree of core material oxidation and hydrogen generation to occur, as well as elevated core temperatures during the ex-vessel accident phase. The eutectics model simulation exhibits more significant degradation of core components during the late in-vessel accident phase – more debris forms and relocates to the lower plenum before lower head failure. The larger debris bed observed in the eutectics model simulation also reaches higher temperatures, presenting a more significant thermal challenge to the lower head until its failure. At the end of the simulated accident scenario, however, core damage is comparable between both simulations due to significant core degradation that occurs during the ex-vessel phase in the interactive materials model simulation. A key difference between the two models’ performance is the maximum temperatures that can be reached in the core and therefore the maximum ΔT between any two components. When implementing the interactive materials model, users have the option to modify the liquefaction temperature of the ZrO 2 -interactive and UO 2 -interactive materials as a way to mimic early fuel rod failure due to material interactions. Through modification of the liquefaction of high melting point materials with significant mass, users may inadvertently limit maximum core temperatures for fuel, cladding, and debris components.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗