Search NASA⌕ Search

Engineering topics

Sklyanskiy, Evgeniy

Publications and source records attributed to Sklyanskiy, Evgeniy.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2022

Mid-Air Helicopter Delivery at Mars Using a Jetpack

Mid-Air Helicopter Delivery (MAHD) is a new Entry, Descent and Landing (EDL) architecture to enable in situ mobility for Mars science at lower cost than previous rover missions. It uses a jetpack to slow down a Mars Science Helicopter (MSH) after separation from the backshell, and reach aerodynamic conditions suitable for helicopter take-off in mid air. MAHD's lander-free approach leaves enough room in the aeroshell to accommodate larger rotors. This drastically improves flight performance compared to heritage EDL approaches, notably +60\% science payload mass. MAHD also brings cost savings, a simpler architecture, improved surface access and can reach higher elevations on Mars. This paper introduces a design for the MAHD system architecture and operations. We present a mechanical configuration which fits both MSH and the jetpack within the 2.65-m Mars heritage aeroshell, and a jetpack control architecture which fully leverages the available helicopter avionics. We discuss preliminary numerical models of the flow dynamics resulting from the interaction between the jets, the rotors and the side winds. We define a force-torque sensing architecture capable of handling the wind and trimming the rotors to prepare for safe take-off. Finally, we analyze the dynamic environment and closed-loop control simulation results to demonstrate the preliminary feasibility of MAHD.

Balaram, J.↗
NASA NTRS2020

Motivations and Preliminary Design for Mid-Air Deployment of a Science Rotorcraft on Mars

Mid-Air Deployment (MAD) of a rotorcraft during Entry, Descent and Landing (EDL) on Mars eliminates the need to carry a propulsion or airbag landing system. This reduces the total mass inside the aeroshell by more than 100 kg, aeroshell complexity, and likely the risk and cost associated to the mission. Moreover, the lighter entry mass enables landing in the Martian highlands, at elevations inaccessible to current EDL technologies. This paper proposes a novel MAD concept for a Mars helicopter. We suggest a minimum science payload package to perform relevant science in the highlands. A variant of the Ingenuity helicopter is proposed to provide increased deceleration during MAD, and enough lift to fly the science payload in the highlands. We show in simulation that the lighter aeroshell results in lower terminal velocity (30 m/s) at the end of the parachute phase of the EDL, and at higher altitudes than other approaches. After discussing the aerodynamics, controls, guidance and mechanical challenges associated to deploying at such speed, we propose a backshell architecture that addresses them to release the helicopter in the safest conditions. Finally, we implemented the helicopter model and aerodynamic descent perturbations in the JPL Dynamics and Real-Time Simulation (DARTS) framework. Preliminary performance evaluation indicate landing and helicopter operations can be achieved up to +5 km MOLA.

Rapin, William↗
NASA NTRS2020

Terrain Relative Navigation for Guided Descent on Titan

Titan’s dense atmosphere, low gravity, and high winds at high altitudes create descent times of >90 minutes with standard entry/descent/landing (EDL) architectures and result in large unguided landing ellipses, with 99% values of 110x110 km and 149x72 km in recent Titan lander proposals. Enabling precision landing on Titan could increase science return for the types of missions proposed to date and make additional types of landing sites accessible, opening up new possibilities for science investigations. Precision landing on Titan has unique challenges, because the hazy atmosphere makes it difficult to see the surface and because it requires guided descent with divert ranges that are one to two orders of magnitude larger than needed for other target bodies, i.e. up to on the order of 100 km. It is conceivable that such a divert capability could be provided economically by a parafoil or other steerable aerodynamic decelerator deployed several 10s of km above the surface. The long descent times lead to large inertial navigation errors, hence a need for terrain relative navigation (TRN). This would require a TRN capability that can operate at such altitudes, despite challenges of seeing the surface sufficiently clearly and of depending on map products that are two orders of magnitude lower in spatial resolution than those for Mars and airless bodies. We then develop algorithms for map matching and feature tracking with descent images and test these with synthetic images created from Cassini/Huygens data sets and our radiative transfer model. We also introduce new possibilities for TRN based on the potential to discriminate some specific types of terrain onboard in descent imagery, such as lake vs adjacent ground and dune vs interdune. We use sensor measurement noise models in simulations of state estimation with an extended Kalman filter that includes coordinates of a set of tracked features in the state vector. Case studies were done for two notional landing sites, one in a site with only dry ground and one in a Titan lake district. In both cases, the filter error model shows 3 position error at touchdown on the order of 2 km. More work is needed to validate these results with higher fidelity camera models and larger data sets, but this is very promising.

Matthies, Larry↗
NASA NTRS2019

2018 Mars Insight Trajectory Reconstruction and Performance from Launch Through Landing

The InSight mission successfully launched to Mars on an Atlas V 401 launch vehicle from the Western Test Range (WTR) at Vandenberg Air Force Base (VAFB) at 04:05:00 PDT on May 5th, 2018 and landed in the Elysium Planitia Region on November 26th, 2018. Data confirming nominal touchdown was received at 11:52:59 AM PST. This paper summarizes in detail the actual vs. predicted performance of the InSight spacecraft and all associated assets in terms of launch vehicle events, injection performance, DSN performance, cruise performance, and Entry, Descent, and Landing events.

Abilleira, Fernando↗
NASA NTRS2019

Maneuver design overview of the 2018 InSight Mars lander mission

Launched on May 5, 2018, the Interior Exploration using Seismic Investigations, Geodesy, and Heat Transport (InSight) spacecraft landed safely on Mars on November 26, 2018. To deliver the lander accurately to the landing site, six trajectory correction maneuvers (TCMs) were planned along the reference trajectory from Earth launch to Mars entry. For the last two TCMs, there were two corresponding contingency TCMs planned that could be executed in the event that the corresponding nominal one failed. There were also twenty pre-designed menu TCMs available for execution at the time of the last contingency TCM, about 8 hours before the Mars entry, descent, and landing. This navigation paper overviews the maneuver design of each TCM, as well as how each one actually performed during operations.

Wallace, Mark↗
NASA NTRS2019

Atmospheric impacts on EDL maneuver targeting for the InSight mission and unguided Mars landers

Early in operational testing for the InSight mission to Mars, it was discovered that the final maneuver to target the entry-interface point (EIP) was unexpectedly sensitive, in both magnitude and direction, to planned atmosphere model updates that would be based on real-time measurements of the Martian atmosphere by Mars Reconnaissance Orbiter (MRO). Upon investigation, the team realized that the Phoenix mission also discovered this sensitivity during its operational testing. A further investigation identified that maneuver sensitivity to real-time atmosphere updates was a result of the fact that both the EFPA and ground target were being held fixed, constraining the maneuver in a way that forced the entry time to change in order to compensate for changes to the nominal trajectory from updating the atmosphere model. The final maneuver occurs 22 hours prior to entry, at which point it is very expensive to change entry time. The study also revealed that any unguided Mars entry, descent, and landing (EDL) mission would be impacted by this sensitivity if it used real-time atmosphere observations to model the nominal expected atmosphere used for maneuver targeting of the EIP. This paper discusses the results of that investigation and presents a number of mitigations as well as the consequences of ignoring the sensitivity.

Kipp, Devin↗
NASA NTRS2019

Navigation performance of the 2018 InSight Mars Lander mission

The NASA InSight spacecraft was launched successfully from Vandenberg Air Force Base on an Atlas V 401 launch vehicle on May 5, 2018 and landed on November 26, 2018. Accurate targeting to the atmospheric entry point by the Navigation team achieved by carefully controlling the final entry flight path angle to -12.0 degrees with a tolerance of +/- 0.21 degrees. This paper will describe how the InSight Navigation team met this difficult task in the presence of frequent unbalanced thrusting for attitude control. The continuous correction for this unplanned ∆V far exceeded pre-launch expectations and proved a challenge to predict accurately.

Wallace, Mark↗
NASA NTRS2018

2018 Mars Insight Mission Design and Navigation Overview

Originally scheduled for a launch in the 2016 Earth to Mars opportunity, NASA’s Interior Exploration using Seismic Investigations, Geodesy, and Heat Transport (InSight) mission will launch the next lander to Mars in May-June 2018 arriving to the Red Planet in November 2018. Derived from the Phoenix mission which successfully landed on Mars in May 2008, the InSight Entry, Descent, and Landing system will place a lander in the Elysium Planitia region. This paper specifies the mission and navigation requirements set by the Project and how the final mission and navigation design satisfies those requirements.

Abilleira, Fernando↗
NASA NTRS2016

DSENDS: multi-mission flight dynamics simulator for NASA missions

Increasingly complex space missions require powerful and flexible simulation environments in order to design, analyze, and operate the missions. NASA’s Jet Propulsion Laboratory has created the DSENDS simulation environment that addresses these needs for a wide range of space missions. In this paper, we describe the DSENDS simulation environment and the key architectural components that make DSENDS a useful simulation and analysis framework. We also overview a variety of NASA missions and flight experiments that are using DSENDS.

Sklyanskiy, Evgeniy↗
NASA NTRS2016

Final Mission and Navigation Design for the 2016 Mars InSight Mission

NASA’s Interior Exploration using Seismic Investigations, Geodesy, and Heat Transport (InSight) mission was scheduled to launch the next lander to Mars in March 2016 arriving to the Red Planet in the fall. Derived from the Phoenix mission which successfully landed on Mars in May 2008, the InSight Entry, Descent, and Landing system will place a lander in the Elysium Planitia region. This paper specifies the mission and navigation requirements set by the Project and how the final mission and navigation design satisfies those requirements. Background information affecting navigation including spacecraft modeling and the physical environment which influences the spacecraft motion are included. (Note from the author: The InSight launch in 2016 was suspended due to critical issues with the Seismic Experiment for Interior Structure (SEIS) instrument that could not be fixed prior to the planned launch period. This paper represents the state of the design for the 2016 mission. No attempt has been made to reflect the latest developments).

Abilleira, Fernando↗
NASA NTRS2016

A High-Heritage Blunt-Body Entry, Descent, and Landing Concept for Human Mars Exploration

Human-scale landers require the delivery of much heavier payloads to the surface of Mars than is possible with entry, descent, and landing (EDL) approaches used to date. A conceptual design was developed for a 10 m diameter crewed Mars lander with an entry mass of approx.75 t that could deliver approx.28 t of useful landed mass (ULM) to a zero Mars areoid, or lower, elevation. The EDL design centers upon use of a high ballistic coefficient blunt-body entry vehicle and throttled supersonic retro-propulsion (SRP). The design concept includes a 26 t Mars Ascent Vehicle (MAV) that could support a crew of 2 for approx.24 days, a crew of 3 for approx.16 days, or a crew of 4 for approx.12 days. The MAV concept is for a fully-fueled single-stage vehicle that utilizes a single pump-fed 250 kN engine using Mono-Methyl Hydrazine (MMH) and Mixed Oxides of Nitrogen (MON-25) propellants that would deliver the crew to a low Mars orbit (LMO) at the end of the surface mission. The MAV concept could potentially provide abort-to-orbit capability during much of the EDL profile in response to fault conditions and could accommodate return to orbit for cases where the MAV had no access to other Mars surface infrastructure. The design concept for the descent stage utilizes six 250 kN MMH/MON-25 engines that would have very high commonality with the MAV engine. Analysis indicates that the MAV would require approx.20 t of propellant (including residuals) and the descent stage would require approx.21 t of propellant. The addition of a 12 m diameter supersonic inflatable aerodynamic decelerator (SIAD), based on a proven flight design, was studied as an optional method to improve the ULM fraction, reducing the required descent propellant by approx.4 t.

Mars lander↗