Engineering topics

Sliwa, Steven M.

Publications and source records attributed to Sliwa, Steven M..

5 records

NASA NTRS1989

A closed-form trim solution yielding minimum trim drag for airplanes with multiple longitudinal-control effectors

Airplane designs are currently being proposed with a multitude of lifting and control devices. Because of the redundancy in ways to generate moments and forces, there are a variety of strategies for trimming each airplane. A linear optimum trim solution (LOTS) is derived using a Lagrange formulation. LOTS enables the rapid calculation of the longitudinal load distribution resulting in the minimum trim drag in level, steady-state flight for airplanes with a mixture of three or more aerodynamic surfaces and propulsive control effectors. Comparisons of the trim drags obtained using LOTS, a direct constrained optimization method, and several ad hoc methods are presented for vortex-lattice representations of a three-surface airplane and two-surface airplane with thrust vectoring. These comparisons show that LOTS accurately predicts the results obtained from the nonlinear optimization and that the optimum methods result in trim drag reductions of up to 80 percent compared to the ad hoc methods.

Goodrich, Kenneth H.↗

NASA NTRS1989

Overview of Dynamics Integration Research (DIR) program at Langley Research Center

Research goals and objectives for an ongoing activity at Langley Research Center (LaRC) are described. The activity is aimed principally at dynamics optimization for aircraft. The effort involves active participation by the Flight Systems, Structures, and Electronics directorates at LaRC. The Functional Integration Technology (FIT) team has been pursuing related goals since 1985. A prime goal has been the integration and optimization of vehicle dynamics through collaboration at the basic principles or equation level. Some significant technical progress has been accomplished since then and is reflected here. An augmentation for this activity, Dynamics Integration Research (DIR), has been proposed to NASA Headquarters and is being considered for funding in FY 1990 or FY 1991.

Sliwa, Steven M.↗

NASA NTRS1989

Modal techniques for analyzing airplane dynamics

A series of techniques are presented for analyzing airplane control and output characteristics. State-space matrix equations describing the linear perturbation dynamics are transformed from physical coordinates into scaled, modal coordinates. Techniques for analyzing the impacts of system inputs on the fundamental modes of motion and the appearance of these modes in the system outputs are explained. Scaled modal matrices are used to compute steady-state control inputs which optimize the steady-state response of selected system outputs. Graphics which promote quick understanding of the analysis are presented to display the resulting vectors and matrices. The defined analysis techniques are applied to an example airplane model, illustrating the insight which can be acquired using the described modal techniques.

Arbuckle, P. Douglas↗

NASA NTRS1987

Flight investigation of the effect of tail configuration on stall, spin, and recovery characteristics of a low-wing general aviation research airplane

Flight tests were performed to investigate the stall, spin, and recovery characteristics of a low-wing, single-engine, light airplane with four interchangeable tail configurations. The four tail configurations were evaluated for effects of varying mass distribution, center-of-gravity position, and control inputs. The airplane tended to roll-off at the stall. Variations in tail configuration produced spins ranging from 40 deg to 60 deg angle of attack and turn rates of about 145 to 208 deg/sec. Some unrecoverable flat spins were encountered which required use of the airplane spin chute for recovery. For recoverable spins, antispin rudder followed by forward wheel with ailerons centered provided the quickest spin recovery. The moderate spin modes agreed very well with those predicted from spin-tunnel model tests, however, the flat spin was at a lower angle of attack and a slower rotation rate than indicated by the model tests.

Stough, H. Paul, III↗

NASA NTRS1987

Linear optimum trim solution for aircraft with three longitudinal control effectors

A simple and fast linear optimum method for trimming aircraft with a combination of three longitudinal aerodynamic or propulsive control effectors is developed, with application to preliminary design or in-flight scheduling. A Lagrangian formulation is used to determine the longitudinal load distribution which minimizes trim drag. Trim drag results obtained with the linear optimum method are similar to those obtained with a nonlinear optimum method, and significant trim drag reductions are found using either optimum method, in comparison with results obtained using various ad hoc methods.

Goodrich, Kenneth H.↗