Search NASA⌕ Search

Engineering topics

Smeltzer, D. B.

Publications and source records attributed to Smeltzer, D. B..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Evaluation of an electronic scanner of pressure (ESOP) module

An electronic scanner of pressure (ESOP) module, developed by NASA Ames Research Center, was installed in a wind tunnel and evaluated over a 5-month testing period. The solid-state ESOP module has 48 miniature pressure transducers and a heater circuit to maintain a constant module temperature. During the wind tunnel test, the module was subjected to an environmental temperature range from 60 F to 104 F, and to considerable module vibration. Zero drift was within + or - 0.5 percent of full-scale output for 37 of the transducers, and was greater than 5.0 percent for four transducers. Pressure measurements from 12 transducers were compared with Scanivalve modules. The agreement of these measurements was considered to be good.

Smeltzer, D. B.↗
NASA NTRS1983

Experimental wing and canard jet-flap aerodynamics

The effects of upper surface blowing on the aerodynamics of a 1/2-span wing/body/canard configuration are shown. The results expand a data base that is limited at high subsonic Mach numbers (M = 0.6-0.9), data that are needed if computational techniques are to be developed for the complex flowfields generated by jet blowing. At lift coefficients greater than about 1.0, the thrust removed drag coefficient was lower with jet blowing than without jet blowing. This favorable effect increased with increasing jet blowing coefficient, and, for a fixed coefficient, simultaneous wing/canard jet blowing was slightly more effective than blowing either surface alone.

Smeltzer, D. B.↗
NASA NTRS1982

Inlet and airframe compatibility for a V/STOL fighter/attack aircraft with top-mounted inlets

Aerodynamic force and inlet pressure data are obtained for 9.5% force and pressure models of a V/STOL fighter/attack aircraft configuration with top mounted twin inlets. Data are presented from tests conducted in the Ames Unitary Wind Tunnels at Mach numbers of 0.6, 0.9, and 1.2 at angles of attack up to 27 deg. and angles of sideslip up to 12 deg. Trimmed aerodynamic characteristics and inlet performance are compared for three different leading edge extension (LEX) configurations. The effects of wing leading and trailing-edge flaps on the inlet are also determined. Maneuver perfromance is calculated form combined force and inlet pressure data. The largest of the three LEX sizes tested gives the best airplane maneuver performance. Wing flap deflections improved inlet recovery at all Mach numbers.

Durston, D. A.↗
NASA NTRS1982

Inlet and airframe compatibility for a V/STOL fighter/attack aircraft with top-mounted inlets

Aerodynamic force and inlet-pressure data were obtained for 9.5% force and pressure models of a V/STOL fighter/attack aircraft configuration with top-mounted twin inlets. Data are presented from wind tunnel tests conducted at Mach numbers of 0.6, 0.9, and 1.2 at angles of attack up to 27-deg and angles of sideslip up to 12-deg. Trimmed aerodynamic characteristics and inlet performance were compared for three different leading-edge extension (LEX) configurations. The effects of wing leading- and trailing-edge flaps on the inlet were also determined. Maneuver performance was calculated from combined force and inlet-pressure data. The largest of the three LEX sizes tested gave the best airplane maneuver performance. Wing flap deflections improved inlet recovery at all Mach numbers.

Durston, D. A.↗
NASA NTRS1981

Airframe effects on top-mounted inlet systems for VSTOL fighter aircraft

Inlet flow-field and compressor-face performance data were obtained for a 0.095-scale model of a VSTOL fighter-attack aircraft configuration with twin top-mounted inlets. Tests were conducted at Mach numbers from 0.6 to 2.0 and at angles of attack and sideslip up to 27 deg and 12 deg, respectively. The effects of inlet location, wing leading-edge extension planform area, canopy-dorsal integration, and variable incidence canards were determined. The results show that distortion at the compressor face when maneuvering is relatively low (20% or less) at Mach numbers up to 0.9. However, at Mach numbers of 1.2 and above, maneuverability may be restricted because of high distortion or low pressure recovery (80% or less) or both.

Smeltzer, D. B.↗
NASA NTRS1981

Top-mounted inlet system feasibility for transonic-subsonic fighter aircraft applications

To inlet flow field and engine inlet performance data for an advanced fighter aircraft configuration were obtained over the Mach 0.6 to 2.0 range. The studies not only provided extensive data for the baseline arrangement, but also evaluated the effects of key aircraft configuration variables (inlet location, canopy-dorsal integration, wing leading-edge extension planform area, and variable incidence canards) on top inlet performance. In order to set these data in the context of practical aircraft systems top inlet performance is compared with that of more conventional inlet/airframe integrations. The results of these evaluations show that, for the top inlet configuration tested, relatively good inlet performance and compatibility characteristics are maintained during subsonic and transonic maneuver. However, at supersonic speeds, flow expansion over the forebody and wings causes an increase in local inlet Mach number subsequently reduces inlet performance levels. These characteristics infer that although top inlets many not pose a viable design option for aircraft requiring a high degree of supersonic maneuverability, they have distinct promise for vehicles with subsonic and transonic maneuver capabilities.

Williams, T. L.↗
NASA NTRS1981

Top-mounted inlet system feasibility for transonic-supersonic fighter aircraft

The more salient findings are presented of recent top inlet performance evaluations aimed at assessing the feasibility of top-mounted inlet systems for transonic-supersonic fighter aircraft applications. Top inlet flow field and engine-inlet performance test data show the influence of key aircraft configuration variables-inlet longitudinal position, wing leading-edge extension planform area, canopy-dorsal integration, and variable incidence canards-on top inlet performance over the Mach range of 0.6 to 2.0. Top inlet performance data are compared with those or more conventional inlet/airframe integrations in an effort to assess the viability of top-mounted inlet systems relative to conventional inlet installations.

Williams, T. L.↗
NASA NTRS1976

Study of two axisymmetric inlets designed for Mach 3.5

Results from wind-tunnel tests of two large-scale models of axisymmetric mixed-compression inlet systems designed for Mach number 3.5 are compared. One inlet incorporated a 'traveling'-bleed system in an effort to achieve maximum transonic engine airflow supply. The other inlet required only a 'fixed'-bleed system, but had 21 percent less transonic airflow supply. The inlet with fixed bleed appears more attractive, if auxiliary airflow systems are used to increase the transonic airflow supply, because it can be 45 percent shorter and would be considerably lighter than the traveling-bleed inlet. In addition, the fixed-bleed inlet offers more operating-control margin at supersonic Mach numbers when the inlet is started. Further, its off-design performance is higher because separation of the flow in the subsonic diffuser can be avoided - something that apparently cannot be done with a traveling-bleed inlet without reducing the transonic airflow supply. Finally, it appears that the management and efficiency of bleed airflow for the fixed-bleed inlet can be improved using analytical methods verified by the tests.

Sorensen, N. E.↗
NASA NTRS1974

Variable geometry for supersonic mixed-compression inlets

Study of two-dimensional and axisymmetric supersonic mixed-compression inlet systems has shown that the geometry of both systems can be varied to provide adequate transonic airflow to satisfy the airflow demand of most jet engines. Collapsing geometry systems for both types of inlet systems provide a generous amount of transonic airflow for any design Mach number inlet system. However, the mechanical practicality of collapsing centerbodies for axisymmetric inlet systems is doubtful. Therefore, translating centerbody axisymmetric inlets with auxiliary airflow systems to augment the transonic airflow capability are an attractive alternative. Estimates show that the capture mass-flow ratio at Mach number 1.0 can be increased approximately 0.20 for a very short axisymmetric inlet system designed for Mach number 2.37. With this increase in mass-flow ratio, even variable-cycle engine transonic airflow demand can be matched without oversizing the inlet at the design Mach number.

Sorensen, N. E.↗
NASA NTRS1974

Wind tunnel and flight performance of the YF-12 inlet system

The steady-state internal performance from 1/3-scale and full-scale wind tunnel models of the YF-12 inlet system is compared with results from flight tests. All systems were thoroughly instrumented for static and total pressure measurements. Results obtained included the inlet mass flows, surface pressure distribution, boundary layer profiles, and detailed total pressure measurements at the engine face. Inlet performance is compared at Mach numbers 2.1 and 2.8 and at several Reynolds numbers over a wide range of inlet operating conditions. Analysis generally shows good agreement in the results between the three systems when inlet conditions are closely matched.

Smeltzer, D. B.↗
NASA NTRS1973

Analytic and experimental performance of two isentropic mixed compression axisymmetric inlets at Mach numbers 0.8 to 2.65

A mixed compression axisymmetric inlet model with a capture diameter of 50 cm was tested at Mach numbers ranging from 0.8 to 2.65 at 0 deg angle of attack and a constant total pressure of approximately 1 atm. Analytical methods accounting for the effects of both viscous and inviscid flows and incorporating empirical bleed discharge coefficients were used in the procedure for designing the inlet contours and the bleed system. Experimental results are compared with analytic predictions and are also compared with results from earlier tests of an inlet with the same internal contours but with a bleed system developed by cut and try methods in the wind tunnel. With the bleed configuration predicted by the design procedure, maximum total pressure recovery at the engine face at the design Mach number of 2.65 was 93 percent, with a total pressure distortion less than 10 percent. Corresponding bleed mass flow was approximately 7.5 percent, which was about 1.3 percent less than predicted. At lower supersonic Mach numbers, pressure recovery and bleed were generally lower and distortion generally higher.

Smeltzer, D. B.↗
NASA NTRS1973

Advanced supersonic inlet technology.

Recently, relatively new analytical procedures have been successfully used to design bleed systems for mixed-compression inlets designed to operate efficiently up to Mach number 2.65. The procedures used constitute a major advance in inlet technology by offering a promising approach to attain high internal and external performance for mixed-compression inlets that operate over a large supersonic Mach number range. Unfortunately, there is a lack of data describing bleed hole performance characteristics to verify these procedures at high Mach numbers. This paper briefly discusses the analytical procedures for designing advanced inlet systems and suggests facility modifications wherein the procedures can be verified on large-scale inlet models up to approximately Mach number 4.5.

Sorensen, N. E.↗
NASA NTRS1972

Tests of a mixed compression axisymmetric inlet with large transonic mass flow at Mach numbers 0.6 to 2.65

A 38.8-cm (15.28-in.) capture diameter model of a mixed-compression axisymmetric inlet system with a translating cowl was designed and tested. The internal contours, designed for Mach number 2.65, provided a throat area of 59 percent of the capture area when the cowl was retracted for transonic operation. Other model features included a boundary-layer removal system, vortex generators, an engine airflow bypass system, cowl support struts, and rotating rakes at the engine face. All tunnel testing was conducted at a tunnel total pressure of about 1 atm (a unit Reynolds number of about 8.53 million/m at Mach number 2.65) at angles of attack from 0 deg to 4 deg. Results for the following were obtained: total-pressure recovery and distortion at the engine face as a function of bleed mass-flow ratio, the effect of bleed and vortex generator configurations on pressure recovery and distortion, inlet tolerance to unstart due to changes in angle of attack or Mach number, surface pressure distributions, boundary-layer profiles, and transonic additive drag. At Mach number 2.65 and with the best bleed configurations, maximum total pressure recovery at the engine face ranged from 91 to 94.5 percent with bleed mass-flow ratios from 4 to 9 percent, respectively, and total-pressure distortion was less than 10 percent. At off-design supersonic Mach numbers above 1.70, maximum total-pressure recoveries and corresponding bleed mass flows were about the same as at Mach number 2.65, with about 10 to 15 percent distortion. In the transonic Mach number range, total pressure recovery was high (above 96 percent) and distortion was low (less than 15 percent) only when the inlet mass-flow ration was reduced 0.02 to 0.06 from the maximum theoretical value (0.590 at Mach number 1.0).

Smeltzer, D. B.↗
NASA NTRS1972

Investigation of a mixed compression axisymmetric inlet at Mach number 5.3

The hypersonic diffuser portion of an uncooled high performance mixed compression, axisymmetric inlet suitable for subsonic burning engines was designed and tested. Performance of a model with a 25.4-cm capture diameter was measured in a wind tunnel and the results were compared with theoretical predictions calculated by a comprehensive computer program. All tests were conducted at a Mach number of 5.3 at a total temperature of 667 K and a total pressure of 11.57 atm. The angle of attack ranged from 0 to + or - 3 deg. Performance at angle of attack remained high. Reasonably high performance in the throat (maximum throat pitot-pressure recovery of 77 percent and an average value of 58 percent) was obtained at 0 deg angle of attack with relatively large amounts of boundary-layer bleed (11 to 22 percent of the capture mass flow). The computer program used in the design of this inlet is considered marginally adequate for predicting hypersonic inlet flow fields. Although the program as it now exists is very useful, an improved computer program that more accurately predicts the boundary layer and the shock-wave-boundary-layer interaction and accounts for boundary-layer bleed should be developed for reliability predicting hypersonic inlet flow fields.

Latham, E. A.↗
NASA NTRS1972

Performance estimates for a supersonic axisymmetric inlet system.

Results of recent tests of a large-scale axisymmetric mixed-compression inlet system designed for Mach number 2.65 indicate that the performance of the supersonic diffuser and required boundary-layer bleed system can be accurately estimated with relatively new analytic methods. Thus, many wind tunnel testing hours can be saved by avoiding much of the usual ?cut and try' wind tunnel development.

Sorensen, N. E.↗