Search NASA⌕ Search

Engineering topics

Smirnov, R. D.

Publications and source records attributed to Smirnov, R. D..

7 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Interaction of SPI pellets with plasma on JET and associated disruptions

Abstract The presented data refer to the Shattered Pellet Injector (SPI) experiments carried out at JET in 2019–2020. This paper is a full journal version of the data originally presented as posters at TMPDM_2020 and EPS_2021. This paper presents various aspects of the interaction of pellets with plasma and associated disruptions. The experiment was performed with I p = (1.1–3.1) MA plasmas and mainly with Ne + D 2 pellet composition, but also with Ar pellets. The Current Quench (CQ) time, τ 80−20 , is the key characteristic of mitigation effectiveness. A pellet with a high content of Ne or Ar can reduce the CQ duration below the upper required JET threshold. Plasmas with high (thermal + internal poloidal magnetic) pre-disruptive plasma energy require a high content of Ne pellets to obtain a short CQ duration. Pellets with a small amount of Ne (and accordingly large amount of D), instead of causing a mitigated CQ, create the conditions for a ‘cold’ Vertical Displacement Events (VDE). The SPI was applied to plasma with different status: mainly to normal (‘healthy’) plasma, i.e. not prone to disruption, post-disruptive and VDE plasma. This study shows that SPI effectiveness in terms of CQ duration and, accordingly, EM loads does not depend on the state of the plasma, whether it is ‘healthy’ or post-disruptive plasma. SPI has been shown to reduce the axisymmetric vertical vessel reaction forces by about (30–40) % compared to unmitigated disruptions. On JET, the VDE, whether ‘hot’ or ‘cold’, always creates the conditions for a toroidal asymmetry in the plasma, so the VDE on the JET is referred to as Asymmetric VDE (AVDE). The interrupting of VDE and prevention of AVDE with SPI has been demonstrated. Thus, the effectiveness of disruption mitigation using SPI has been confirmed.

Gerasimov, S. N. (ORCID:0009000237937211)↗
DOE OSTI2024

On the force exerted on a non-spherical asymmetric dust grain from homogeneous, stationary, isotropic, non-magnetized plasma

Whereas the conventional wisdom suggests that the force between non-magnetized homogeneous, stationary, isotropic plasma, and the dust grain is only possible for the case of relative plasma–grain velocity, it is shown that stationary non-spherical asymmetric dust grain immersed in stationary, non-magnetized, isotropic plasma can experience a force caused by the grain–plasma interactions. The component of the force due to scattering of plasma particles in the limit of infinite Debye length is considered analytically. Both the particle scattering and absorption force components are modeled numerically in the limits of infinite and finite Debye length using a newly developed 2D3V Aspherical Particle-in-Cell code. The code simulates interactions of dust grain of selected non-spherical asymmetric shape with plasmas using dust shape conforming coordinates. Here, the simulations confirm the existence of the force on non-spherical asymmetric grain in stationary non-magnetized plasma and show that the plasma screening effects can lead to reversal of the force direction.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Modeling of carbon and tungsten transient dust influx in tokamak edge plasma

The paper presents computer simulation studies of burst injection of carbon and tungsten dust particles in DIII-D-like edge plasmas. The injection causes a large transient influx of the low- and high-Z impurities associated with the dust ablation in the plasmas. The dust transport and the effects of the ablated impurities on the edge plasma dynamics in a modern mid-size tokamak geometry are investigated for low- and high-power plasma discharge conditions. The core plasma contamination with dust-ablated impurities and the factors affecting it are evaluated.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Simulations of divertor plasmas with inverse sheaths

The effect of strong electron emission from material surfaces has been proposed to form an “inverse sheath”: a region with a positive potential relative to the near-wall plasma which prevents the flow of ions to the wall [M. D. Campanell, “Negative plasma potential relative to electronemitting surfaces,” Phys. Rev. E. 88, 033103 (2013); M. D. Campanell and M. V. Umansky, “Strongly emitting surfaces unable to float below plasma potential,” Phys. Rev. Lett. 116, 1–5 (2016); M. D. Campanell and G. R. Johnson, “Thermionic cooling of the target plasma to a sub-ev temperature,” Phys. Rev. Lett. 122, 1–5 (2019)]. We assess the viability of this regime in a tokamak device using the 2D edge plasma transport code UEDGE [T. Rognlien et al ., “A fully implicit, time dependent 2-D fluid code for modeling tokamak edge plasmas,” J. Nucl. Mater. 196–198, 347–351 (1992)]. Since the UEDGE code does not consider the sheath region directly, we apply boundary conditions at the divertor targets which emulate the physics of both “standard” and “inverse” sheath regimes [R. Masline et al ., “Influence of the inverse sheath on divertor plasma performance in tokamak edge plasma simulations,” Contrib. Plasma Phys. 60, e201900097 (2020)]. Using these boundary conditions, we perform scoping studies to assess plasma parameters near the target by varying the density at the core-edge interface. We observe a smooth transition in the resultant profiles of plasma parameters for the standard sheath, and a bifurcation across the simulation set for plasmas with an inverse sheath. The cause of this bifurcation is assessed by performing the parameter scan both with and without impurity radiation; we observe that the bifurcation persists in both cases, indicating that this bifurcation is caused by plasma recombination.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Time-dependent modeling of dust outburst into tokamak divertor plasma

The first self-consistent simulation studies of the impact of transient injection of tungsten dust on ITER-like edge plasma are presented. The simulations are performed using DUSTT and UEDGE codes coupled in a fully time-dependent manner. The evolution of the divertor and upstream plasma conditions, following the injection of tungsten dust of various quantities and sizes at the outer strike point, is investigated. The estimates of the core plasma impurity fraction and the core impurity screening factor associated with the dust injection are also obtained. Here, the simulations show that the bursts of even modest amounts of tungsten dust injected into the divertor plasmas can result in large perturbations of the divertor power load and unacceptable levels of the core plasma contamination with tungsten impurities.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Time-dependent modeling of coupled plasma-wall dynamics

Effects of dynamic wall outgassing on divertor plasma during an ELM-like heat pulse are modelled using newly coupled edge plasma code UEDGE and all reaction-diffusion code FACE. Different divertor regimes are simulated depending on the degree of the plasma detachment. It is shown that hydrogen outgassing from the divertor target plate induced by ELM pulse in the semi-detached regime can trigger deep plasma detachment. The induced detachment does not spontaneously reverse after the pulse due to ineffective implantation of low energy plasma hydrogen in the target material. Furthermore, we demonstrate that plasma neutrals play essential role in heat transport in a detached divertor. The modelled hydrogen dynamics in the wall material demonstrates that the heat pulse leads to enhanced hydrogen transport toward the wall bulk.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗