Search NASA⌕ Search

Engineering topics

Smith, A.

Publications and source records attributed to Smith, A..

At least 55 records · Page 3

Differences in Femoral Geometry and Structure Due to Immobilization

Reduction in bone mass of the lower extremity is well documented in individuals with paralysis resulting from spinal cord injury (SCI). The consequent osteopenia leads to elevated fracture risk with fractures occurring more commonly in the femoral shaft and supracondylar regions than the hip. A model has recently been described to estimate geometry and structure of the femoral midshaft from whole body scans by dual X-ray absorptiometry (DXA). Increases in femoral geometric and structural properties during growth were primarily related to mechanical loading as reflected by body mass. In this study, we investigate the relationship between body mass and femoral geometry and structure in adults with normal habitual mechanical loading patterns and those with severely reduced loading. The subjects were 78 ambulatory men (aged 20-72 yrs) and 113 men with complete paralysis from SCI of more than 4 years duration (aged 21 73 yrs). Subregional analysis was performed on DXA whole body scans to obtain bone mineral content (BMC, g), cortical thickness (cm), crosssectional moment of inertia (CSMI, cm4), and section modulus (cm3) of the femoral midshaft. All measured bone variables were significantly lower in SCI compared with ambulatory subjects: -29% (BMC), -33% (cortical thickness), -23% (CSMI), and -22% (section modulus) while body mass was not significantly different. However, the associations between body mass and bone properties were notably different; r2 values were higher for ambulatory than SCI subjects in regressions of body mass on BMC (0.48 vs 0.20), CSMI (0.59 vs 0.32), and section modulus (0.59 vs 0.31). No association was seen between body mass and cortical thickness for either group. The greatest difference between groups is in the femoral cortex, consistent with reduced bone mass via endosteal expansion. The relatively lesser difference in geometric and structural properties implies that there is less effect on mechanical integrity than would be expected from bone mass results alone. The reduced association in SCI subjects between body mass and bone properties is not unexpected. Although mean body mass differs little between ambulatory and SCI individuals, the association between body mass and in vivo skeletal loading is no longer present, as mechanical influences are removed except for transfer activities. The residual association is probably attributable to the strength of this influence during growth. These results highlight the importance of examining geometry and structure in conjunction with bone mass.

Kiratli, Beatrice Jenny↗

High Reynolds Number Effects on Multi-Hole Probes and Hot Wire Anemometers

The paper reports on the results from an experimental investigation of the response of multi-hole and hot wire probes at high flow Reynolds numbers (Re approx. 10(exp 6)). The limited results available in literature for 5-hole probes are restricted to Re approx. 10(exp 4). The experiment aims to investigate the probe response (in terms of dimensionless pressure ratios, characterizing pitch, and yaw angles and the total and static pressures) at high Re values and to gauge their effect on the calculated velocity vector. Hot wire calibrations were also undertaken with a parametric variation of the flow pressure, velocity and temperature. Different correction and calibration schemes are sought to be tested against the acquired data set. The data is in the analysis stage at the present time. The test provided good benchmark quality data that can be used to test future calibration and testing methods.

Ramachandran, N.↗

An Experimental Study of the Flow Emerging from Porous Walls

The fluid mechanics of air flow exiting from porous materials is investigated. Porous walls with filter ratings differing by about three orders of magnitude are studied. The flow behavior is investigated for its spatial and temporal stability. The measurements show that coalescence effects cause jet development which gives rise to a stable, spatial velocity non-uniformity termed pseudo-turbulence. Beyond a critical mean velocity, the pseudo-turbulence shows a leveling trend and the flow exhibits jets whose dimensions are independent of wall porosity and provide a unique length scale for this type of flow field (approx. 1 mm). A correlation is developed to predict the onset of fully developed jets. The impact of using porous wall materials in cold flow solid rocket motor testing is addressed.

Ramachandran, N.↗

An experimental study of the fluid mechanics associated with porous walls

The fluid mechanics associated with the blowing phenomenon from porous walls is measured and characterized. The measurements indicate that the flow exiting a porous wall exhibits a lumpy velocity profile caused by the coalescence effects of smaller jets emerging from the surface. The velocity variations are spatially stable and prevail even at low flow rates. The intensity of this pseudoturbulence is found to be directly proportional to the filter rating of the porous wall and to increase linearly with the mean velocity. Beyond a critical mean velocity, the pseudoturbulence intensity shows a leveling trend with increase in the mean velocity. This critical velocity varies inversely as the filter rating and represents the onset of fully developed jetting action in the flow field. Based on the data, a more appropriate length scale for the flow field is proposed and a correlation is developed that can be used to predict the onset of fully developed jets in the flow emerging from a porous wall.

Ramachandran, N.↗

UIT ultraviolet imaging of 30 Doradus

During the Astro-1 mission, near- and far-UV images of the 30 Doradus region were obtained using the Ultraviolet Imaging Telescope (UIT). These wide-field, 40 min in diameter, high spatial resolution, 2-3 sec, UIT UV images reveal a rich field of luminous UV-bright stars, clusters, and associations. There are 181 stars brighter than m(sub 2558A) = 16.5 and 197 stars brighter than m(sub 1615A) = 16.4 within 3 min diameter of the 30 Doradus central cluster. We have derived UV fluxes emitted from the 30 Doradus central cluster and from its UV bright core, R136. The region within 5 sec of R136 produces approximately 14% of the far-UV flux (lambda = 1892 A) and approximately 16% of the near-UV flux (lambda = 2558 A) emitted from the 3 min diameter central cluster. The derived UV luminosity of R136 at 1892 A is only 7.8 times that of the nearby O6-7 Iaf star, R139, and the m(sub 1892) - m(sub v) colors of R136 are similar to other O or Wolf-Rayet stars in the same region. These UIT data, combined with other published observations at longer wavelengths, indicate that there is no observational evidence for a supermassive star in R136.

Hintzen, P.↗

A monochromator based on W/C multilayers of 40 A layer spacing

The design and preliminary performance data are presented for a monochromator based on two multilayer X-ray mirrors. The monochromator is based on mirrors with a d-spacing of 40 A and is designed to operate in the 5-75 A wavelength regime which can be varied by interchanging the mirrors with ones of different d-spacing. The multilayer mirrors are fabricated using sputter deposition and typically consist of 40 layer pairs of W and C. Except for W/Si, which shows 1-2 percent better reflectivities over the 7-40 A range but 4-10 percent poorer reflectivities for wavelengths longer than 40 A and shorter than 7 A, calculations performed using other combinations of materials generally show poorer reflectivities over the wavelength range of interest. Plans for a four-mirror version of the monochromator that will have increased resolution are also presented.

Smith, A.↗

GIS Integration for Quantitatively Determining the Capabilities of Five Remote Sensors for Resource Exploration

To assist the U.S. Geological Survey in carrying out a Congressional mandate to investigate the use of side-looking airborne radar (SLAR) for resources exploration, a research program was conducted to define the contribution of SLAR imagery to structural geologic mapping and to compare this with contributions from other remote sensing systems. Imagery from two SLAR systems and from three other remote sensing systems was interpreted, and the resulting information was digitized, quantified and intercompared using a computer-assisted geographic information system (GIS). The study area covers approximately 10,000 square miles within the Naval Petroleum Reserve, Alaska, and is situated between the foothills of the Brooks Range and the North Slope. The principal objectives were: (1) to establish quantitatively, the total information contribution of each of the five remote sensing systems to the mapping of structural geology; (2) to determine the amount of information detected in common when the sensors are used in combination; and (3) to determine the amount of unique, incremental information detected by each sensor when used in combination with others. The remote sensor imagery that was investigated included real-aperture and synthetic-aperture radar imagery, standard and digitally enhanced LANDSAT MSS imagery, and aerial photos.

Pascucci, R. F.↗

Hydrazines and carbohydrazides produced from oxidized carbon in earth's primitive environment

Whether abiological organic compounds can be formed from the interactions of energy sources with nitrogen, oxidized carbon and water is held to be of importance in geochemical models of the primordial earth atmosphere. It is reported that experiments using quenched spark discharges through molecular nitrogen on aqueous suspensions of CaCO3 and other reactants to simulate the hydrosphere/atmosphere interface yield hydrazine and carbohydrazine in significant but low yields. Such reactions in primitive aquatic environments may have supplied a pathway for chemical evolution and the origin of life, on a primitive earth in which fully oxidized states of carbon were available for the primary synthesis of organic matter.

Folsome, C. E.↗

An X-ray map of SN 1006 from the Einstein Observatory

An X-ray map of the SN 1006 supernova remnant acquired by the imaging proportional counter of the Einstein Observatory in the energy range 0.1-4 keV is presented. The image obtained from the imaging proportional counter shows a limb-brightened nebula, almost circular in outline with enhanced emission in two quadrants. The hardness ratio map reveals a large range of temperatures over the object, with the highest values near the limbs of the enhanced emission regions. Consideration of a three-dimensional model of the object indicates the presence of a shell of electron temperature varying between 10 to the 6th and 10 to the 7th K and density varying between 0.3 and 6/cu cm surrounding a fairly uniform interior, of electron temperature 1.5 x 10 to the 6th K and density 1.0/cu cm. The optical filaments are observed to lie parallel with the faintest edge of the X-ray shell, about 1 arcmin from the peak of X-ray emission. Mass visible in the X-ray image of 5-15 solar masses suggests that the supernova may have been of type II. No evidence is obtained for a hot stellar remnant.

Pye, J. P.↗

Development of CMOS integrated circuits

Report documents life cycles of two custom CMOS integrated circuits: (1) 4-bit multiplexed register with shift left and shift right capabilities, and (2) dual 4-bit registers. Cycles described include conception as logic diagrams through design, fabrication, testing, and delivery.

Bertino, F.↗

Experimental study of low-energy charge transfer in nitrogen

Total charge transfer cross sections were obtained for the N2(+)-N2 system with relative translational ion energies between 9 and 441 eV. Data were obtained to examine the dependence of total cross section on ion energy. The effect of ion excitation on the cross sections was studied by varying the electron ionization energy in the mass spectrometer ion source over an electron energy range between 14.5 and 32.1 eV. The dependence of total cross section on the neutralization chamber gas pressure was examined by obtaining data at pressure values from 9.9 to 0.000199 torr. Cross section values obtained were compared with experimental and theoretical results of other investigations.

Smith, A.↗

Measurement techniques and applications of charge transfer to aerospace research

A technique of developing high-velocity low-intensity neutral gas beams for use in aerospace research problems is described. This technique involves ionization of gaseous species with a mass spectrometer and focusing the resulting primary ion beam into a collision chamber containing a static gas at a known pressure and temperature. Equations are given to show how charge-transfer cross sections are obtained from a total-current measurement technique. Important parameters are defined for the charge-transfer process.

Smith, A.↗

A small gas inlet system for orbital mass-spectrometer calibrations

A gas inlet system is described for generating precise gas pressures that are to be used as calibration references for the mass spectrometers aboard the dual air density Explorer satellites. This gas inlet system was developed as an inflight calibration technique in which a known amount of onboard gas is released in the satellite cavity and is detected by the mass spectrometer. Although several flight mass spectrometer experiments have been proposed, none make use of the inflight calibration technique described in this report. Laboratory measurements and calibration of the metering leak technique for the gas inlet systems are discussed. The systems tested have metering leak rates between 2 and 4 microliters/sec at 298 K for argon-40, and they produce molecular flow up to 100 torr, which is the highest test pressure in this experiment. Test data show that metering leak rates are reproducible within 1 percent of established means for helium-3, helium-4, and argon-40.

Smith, A.↗

Excerpts from selected LANDSAT 1 final reports in geology

The standard formats for the summaries of selected LANDSAT geological data are presented as checklists. These include: (1) value of LANDSAT data to geology, (2) geologic benefits, (3) follow up studies, (4) cost benefits, (5) optimistic working scales, (6) statistical analysis, and (7) enhancement effects.

Short, N. M.↗

Economical custom LSI arrays

Automatic design technique uses standard circuit cells for producing large-scale integrated arrays. Computerized fabrication process provides individual cells of high density and efficiency, quick turnaround time, low cost, and ease of corrections for changes and errors.

Feller, A.↗

Absolute calibration of Apollo lunar orbital mass spectrometer.

Recent experiments were conducted in Langley Research Center's molecular beam system to perform an absolute calibration of the lunar orbital mass spectrometer which was flown on the Apollo 15 and 16 missions. Tests were performed with several models of the instrument using two test gases, argon and neon, in the 1 ntorr to .1 picotorr range. Sensitivity to argon at spacecraft orbital velocity was .00028 A/torr enabling partial pressures in the .01-picotorr range to be measured at the spacecraft altitude. Neon sensitivity was nearly a factor of 5 less. Test data support the feasibility of using the lunar orbital mass spectrometer as a tool to gather information about the lunar atmosphere.

Yeager, P. R.↗