Search NASA⌕ Search

Engineering topics

Smith, Michael

Publications and source records attributed to Smith, Michael.

At least 73 records · Page 4

Scoping Analysis of Sodium Cooled Fast Spectrum Test Reactor Cores

A team from the national laboratories conducted a study that assessed advanced reactor technology options and the irradiation needs of a broad group of stakeholders. This identified a gap in the fast neutron irradiation capability - the need for a test reactor that can deliver high neutron fluxes of fast neutrons. The study compared fast and thermal neutron irradiation technology options based on technology maturity and the ability to meet strategic objectives, along with pathways to deployment and tradeoffs in mission. It also provided a recommendation on specific technology options to address the current gap in fast neutron irradiation capabilities. In this context, a detailed scope of work was prepared that pertains to a trade study focusing on the core of a fast neutron spectrum test reactor. This report presents the main results obtained by a team of Argonne National Laboratory (ANL) and Idaho National Laboratory (INL) scientists. It aims at developing an overall understanding of how the various areas important to the design and successful operation of such a facility interact with one another. Developing a sense of the relevant sensitivities at a systems level creates an understanding of where and how margins may be available to improve performances (e.g., flux level, capacity factor, and thermal hydraulic limits). Emphasis is given to the reactor (core design options and safety) and its fuel cycle (fuel supply and fabrication, as well as spent fuel management).

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Alternative Impact Limiter Designs for Used/Spent Nuclear Fuel Transportation Casks - 19496

With the need to eventually transport used/spent nuclear fuel (UNF/SNF) from existing storage sites to a consolidated interim storage facility, disposal site, and/or recycling facility, a preliminary evaluation was performed by the University of North Carolina at Charlotte (UNCC) in collaboration with Orano to examine the feasibility of an alternate impact limiter design for Used/Spent Nuclear Fuel Transportation Casks. Many of the previous designs involved complex designs and in some cases, utilized scarce materials, which resulted in expensive impact limiter systems to build and procure. The objective of this evaluation was to examine the availability of alternative materials which could be potentially implemented in simpler designs and result in significant cost savings over some of the current impact limiters designs. The project was divided into three phases: (1) performance of a comprehensive survey of the energy absorbing properties of composite materials that have become available since the original impact limiter designs were licensed; (2) designing and modeling of an impact limiter capable of meeting the hypothetical accident conditions (HAC) identified in 10CFR71.73; and (3) testing of the new materials identified for use in the newly designed impact limiter and feeding this test date to model of the new impact limiter. To design and model the new impact limiter, a specific transportation cask system was selected which was the Orano TN MP187. This paper provides details of the three phases of the project and the estimated cost savings from the new impact limiters. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Nuclear Considerations for the Application of Lanthanum Telluride in Future Radioisotope Power Systems

Thermoelectric-based radioisotope power systems (RPSs) produced in the United States convert the heat generated by the radioactive emission of alpha particles from plutonium dioxide ( 238 puO 2 ) into electricity by means of the Seebeck effect [1]. Certain designs for thermoelectric convertors propose the use of lanthanum telluride (La 3 Te 4 ) materials due to their significant conversion capabilities [2]. The generation of neutrons from spontaneous fission and alpha-neutron (α,n) reactions is also associated with the decay of 238 PuO 2 . A portion of these neutrons will interact with the thermoelectric materials and induce trace amounts of transmutation reactions in various lanthanum and tellurium isotopes. While very small quantities of several transmutation products are predicted, the most significant reaction channels are expected to produce trace amounts of iodine which will accumulate over time. Although iodine is classified as a halogen, it is the least reactive of the halogens, and as such, it is the most likely to be able to chemically convert back into the molecule I 2 . Since I 2 is a gas at RPS temperatures, it may be possible for iodine to attack other components in the thermoelectric cavity of an RPS system. Iodine reacts easily with metals to produce a wide variety of salts. This behavior could affect the performance of La 3 Te 4 thermoelectric devices, particularly the segmented architectures that include multiple sets of bonding and metallization layers. In this type of architecture, several segments of different thermoelectric materials are joined to increase the average thermoelectric figure of merit over a relatively large temperature gradient. It is plausible that sophisticated bonding/metallization layers could be required to join the segment interfaces to each other and to the cold- and hot-shoe materials. The long-term stability and performance of these segmented material combinations could degrade as a result of the potential formation and reactions of metal-iodide compounds at the segment interfaces. This paper (1) investigates the degree to which, if any, this process may threaten potential La 3 Te 4 thermoelectric technologies, (2) presents calculations of the amount of iodine generated over the operational life of a radioisotope thermoelectric generator design, and (3) discusses the potential effects of the resulting material's chemical reactions in a segmented couple-level architecture containing La 3 Te 4 . Conclusions drawn from combined particle transport, transmutation, and thermochemical calculations for La 3 Te 4 thermoelectric materials undergoing a notional 20-year mission scenario suggest that there is no significant potential for transmutation-induced thermoelectric (TE) performance degradation.

Smith, Michael↗

Nuclear Thermal Propulsion Dynamic Modeling with Modelica

Oak Ridge National Laboratory (ORNL) is participating in the nuclear thermal propulsion (NTP) research and development effort supported by the National Aeronautics and Space Administration (NASA). This effort involves collaboration between multiple research groups, representing various government agencies and industry partners. ORNL has developed a Modelica-based modeling package for dynamic system modeling of nuclear reactors called the Transient Simulation Framework of Reconfigurable Models (TRANSFORM). While this software has been successfully demonstrated in simulations of traditional pressurized-water reactors, boiling-water reactors, liquid-metal reactors and molten-salt reactors, it has also been adapted for non-traditional use in modeling hybrid energy systems, and tritium transport. This versatility is being applied to the current NTP project, where specific modules within TRANSFORM are being developed for and applied to transient modeling of the NASA NTP design. This paper presents the current state of the ORNL-NTP model, the utility of TRANSFORM methodologies in NTP transient simulations, the ability to develop NTP-specific modules, and future work for the model.

Rader, Jordan↗

Development of a Mars Lidar (MARLI) for Measuring Wind and Aerosol Profiles from Orbit

Our understanding of the Mars atmosphere and the coupled atmospheric processes that drive its seasonal cycles is limited by a lack of observation data, particularly measurements that capture diurnal and seasonal variations on a global scale. As outlined in the 2011 Planetary Science Decadal Survey and the recent Mars Exploration Program Analysis Group(MEPAG) Goals Document, near-polar-orbital measurements of height-resolved aerosol backscatter and wind profiles area high-priority for the scientific community and would be valuable science products as part of a next-generation orbital science package. To address these needs, we have designed and tested a breadboard version of a direct detection atmospheric wind lidar for Mars orbit. It uses a single-frequency, seeded Nd:YAG laser ring oscillator operating at 1064nm (4 kHz repetition rate), with a 30-ns pulse duration amplified to 4 mJ pulse energy. The receiver uses a Fabry-Perotetalon as part of a dual-edge optical discrimination technique to isolate the Doppler-induced frequency shift of the back scattered photons. To detect weak aerosol backscatter profiles, the instrument uses a 4x4 photon-counting HgCdTeAPD detector with a 7 MHz bandwidth and < 0.4 fW/Hz(exp 1/2) noise equivalent power. With the MARLI lidar breadboard instrument, we were able to measure Doppler shifts continuously between 1 and 30 m/s by using a rotating chopper wheel to impart a Doppler shift to incident laser pulses. We then coupled the transmitter and receiver systems to a laser ranging telescope at the Goddard Geophysical and Astronomical Observatory (GGAO) to measure backscatter and Doppler wind profiles in the atmosphere from the ground. We measured a 5.3 ± 0.8 m/s wind speed from clouds in the planetary boundary layer at a range of 4 to 6 km. This measurement was confirmed with a range-over-time measurement to the same clouds as well as compared to EMC meteorological models. Here we describe the lidar approach and the breadboard instrument, and report some early results from ongoing field experiments.

Cremons, Daniel R.↗

Radioisotope Power System Dose Estimation Tool

The Radioisotope Power System Dose Estimation Tool (RPS-DET) is used to create, perform and analyze particle-transport simulations of radioisotope power systems (RPS). RPS-DET consists of a Matlab graphical user interface (GUI) to generate and analyze Monte Carlo N-Particle (MCNP) 6 input and output files. Simulation geometries are created using a library-based method of combining multiple RPS units and environmental scenarios while source terms are produced from databases of time-dependent photon and neutron spectra generated by the software packages IsoChain and ORIGEN. Simulation results are saved in a three-dimensional format for neutron and photon flux and dose in tissue or silicon and may be interactively inspected via the GUI. RPS-DET allows flexibility in the simulation-space by providing the ability to mix-and-match RPS units with relevant environments along with capturing the effects of fuel-aging for the particle-energy-spectra and intensity. This work has been benchmarked against measurements of existing RPS units and found to comparably predict neutron and gamma flux, absorbed dose, and dose equivalent in humans and electronics (silicon).

Smith, Michael↗

Radioisotope power source dose estimation tool (RPS-DET)

The purpose of this work is to develop a radioisotope power source dose estimation tool (RPS-DET) capable of rapidly predicting accurate neutron and gamma-ray flux/dose implications from various radioisotope power sources (RPSs). RPS-DET can use this information to calculate the flux/dose incident on or absorbed by nearby humans, materials, and electronics over a complex mission lifetime. This simulation tool uses a Matlab user interface to combine common geometry scenarios for traditional and new RPS design configurations to write a particle-transport simulation using Monte Carlo N-Particle (MCNP) 6, which provides results that are automatically post-processed for interactive analysis. The user defines the average age of the PuO2fuel, which determines the appropriate time-dependent gamma-ray and neutron spectra, along with the desired RPS and local environment for the simulation. Results for a given simulation are gamma-ray, neutron, and combined flux spectra, whole-body effective dose for humans, and absorbed dose in silicon for electronics. This work has been benchmarked against measurements of existing RPS units and has been determined to predict neutron and gamma flux, absorbed dose, and dose equivalent within 50% of simulation uncertainties.

Smith, Michael↗

Toward Measuring Prompt Fission Products in Coincidence

Despite the discovery of fission nearly 80 years ago and its importance to nuclear energy, national security, and astrophysics, there are very few measurements of the correlations between multiple fission products. An experiment is underway at Oak Ridge National Laboratory to measure the energy and angle correlations between prompt fission neutrons, γ rays, and fragments. These measurements could reveal the existence of scission neutrons, the energy balance between these products, and other details needed for benchmarking advanced fission models. The setup includes an array of VANDLE neutron detectors and a γ-ray detector positioned opposite a suite of detectors to determine the mass of one fragment. Preliminary results with a spontaneous 252Cf source show expected correlations between prompt fragments and neutrons along the fission axis. Further refinements will improve the resolution of the fragment mass and increase efficiency for triple-coincident events. Future experiments could be done with a neutron beam to study induced fission on thin targets.

Peters, William A.↗

Status of the ITER Ion Cyclotron H&CD

The ITER Ion Cyclotron Heating and Current Drive system (IC H&CD) is designed to deliver 20MW to a broad range of plasma scenarios between 40 and 55MHz, during very long pulses. It consists of two broadband equatorial port plug antennas, their pre-matching and matching systems, transmission lines, Radio Frequency (RF) Sources and High Voltage Power Supplies. The overall project schedule has been revised and agreed by ITER Council; it re-integrates the second antenna and its power supplies in construction baseline and sets the dates for progressive installation with DT phase planned in 2035. Recent progress on ICRF subsystems is reported, covering design evolution, qualification of test articles and specific R&D results in domestic agencies, suppliers, associated laboratories and IO.

Agarwal, Rohit↗

THE SHAPING OF THE MULTIPOLAR PRE-PLANETARY NEBULA CRL 618 BY MULTIDIRECTIONAL BULLETS

In order to understand the formation of the multipolar structures of the pre-planetary nebula CRL 618, we perform 3D simulations using a multidirectional bullet model. The optical lobes of CRL 618 and fast molecular outflows at the tips of the lobes have been found to have similar expansion ages of ∼100 yr. Additional fast molecular outflows were found near the source along the outflow axes with ages of ∼45 yr, suggesting a second episode of bullet ejections. Thus, in our simulations, two episodes of bullet ejections are assumed. The shaping process is simulated using the ZEUS-3D hydrodynamics code that includes molecular and atomic cooling. In addition, molecular chemistry is also included to calculate the CO intensity maps. Our results show the following: (1) Multiepoch bullets interacting with the toroidal dense core can produce the collimated multiple lobes as seen in CRL 618. The total mass of the bullets is ∼0.034 M{sub ⊙}, consistent with the observed high-velocity (HV) CO emission in fast molecular outflows. (2) The simulated CO J = 3–2 intensity maps show that the low-velocity cavity wall and the HV outflows along the lobes are reasonably consistent with the observations. The position–velocity diagram of the outflows along the outflow axes shows a linear increase of velocity with distance, similar to the observations. The ejections of these bullets could be due to magnetorotational explosions or nova-like explosions around a binary companion.

79 ASTRONOMY AND ASTROPHYSICS↗

PROGRESS IN DESIGN OF THE INSTRUMENTATION AND CONTROL OF THE TOKAMAK COOLING WATER SYSTEM

This paper discusses progress in the design of the control, interlock and safety systems of the Tokamak Cooling Water System (TCWS) for the ITER fusion reactor. The TCWS instrumentation and control (I&C) is one of approximately 200 separate plant I&C systems (e.g., vacuum system I&C, magnets system I&C) that interface to a common central I&C system through standardized networks. Several aspects of the I&C are similar to the I&C of fission-based power plants. However, some of the unique features of the ITER fusion reactor and the TCWS (e.g., high quasi-static magnetic field, need for baking and drying as well as cooling operations), also demand some unique safety and qualification considerations. The paper compares the design strategy/guidelines of the TCWS I&C and the I&C of conventional nuclear power plants. Issues such as safety classifications, independence between control and safety systems, sensor sharing, redundancy, voting schemes, and qualification methodologies are discussed. It is concluded that independence and separation requirements are similar in both designs. However, the voting schemes for safety systems in nuclear power plants typically use 2oo4 (i.e., 4 divisions of safety I&C, any 2 of which is sufficient to trigger a safety action), while 2oo3 voting logic - within each of 2 independent trains - is used in the TCWS I&C. It is also noted that 2oo3 voting is also acceptable in nuclear power plants if adequate risk assessment and reliability is demonstrated. Finally, while qualification requirements provide similar guidance [e.g., both IEC 60780 (invoked in ITER-space), and IEEE 323 (invoked in fission power plant space) provide similar guidance], an important qualification consideration is the susceptibility of I&C to the magnetic fields of ITER. Also, the radiation environments are different. In the case of magnetic fields the paper discusses some options that are being considered.

Korsah, Kofi↗

Electrical current leakage and open-core threading dislocations in AlGaN-based deep ultraviolet light-emitting diodes

Electrical current transport through leakage paths in AlGaN-based deep ultraviolet (DUV) light-emitting diodes (LEDs) and their effect on LED performance are investigated. Open-core threading dislocations, or nanopipes, are found to conduct current through nominally insulating Al{sub 0.7}Ga{sub 0.3}N layers and limit the performance of DUV-LEDs. A defect-sensitive phosphoric acid etch reveals these open-core threading dislocations in the form of large, micron-scale hexagonal etch pits visible with optical microscopy, while closed-core screw-, edge-, and mixed-type threading dislocations are represented by smaller and more numerous nanometer-scale pits visible by atomic-force microscopy. The electrical and optical performances of DUV-LEDs fabricated on similar Si-doped Al{sub 0.7}Ga{sub 0.3}N templates are found to have a strong correlation to the density of these nanopipes, despite their small fraction (<0.1% in this study) of the total density of threading dislocations.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

High-resolution coupled physics solvers for analysing fine-scale nuclear reactor design problems

An integrated multi-physics simulation capability for the design and analysis of current and future nuclear reactor models is being investigated, to tightly couple neutron transport and thermal-hydraulics physics under the SHARP framework. Over several years, high-fidelity, validated mono-physics solvers with proven scalability on petascale architectures have been developed independently. Based on a unified component-based architecture, these existing codes can be coupled with a mesh-data backplane and a flexible coupling-strategy-based driver suite to produce a viable tool for analysts. The goal of the SHARP framework is to perform fully resolved coupled physics analysis of a reactor on heterogeneous geometry, in order to reduce the overall numerical uncertainty while leveraging available computational resources. Finally, the coupling methodology and software interfaces of the framework are presented, along with verification studies on two representative fast sodium-cooled reactor demonstration problems to prove the usability of the SHARP framework.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Efficient boron nitride nanotube formation via combined laser-gas flow levitation

A process for producing boron nitride nanotubes and/or boron-carbon-nitrogen nanotubes of the general formula B.sub.xC.sub.yN.sub.z. The process utilizes a combination of laser light and nitrogen gas flow to support a boron ball target during heating of the boron ball target and production of a boron vapor plume which reacts with nitrogen or nitrogen and carbon to produce boron nitride nanotubes and/or boron-carbon-nitrogen nanotubes of the general formula B.sub.xC.sub.yN.sub.z.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Distributed Assimilation of Satellite-based Snow Extent for Improving Simulated Streamflow in Mountainous, Dense Forests: An Example Over the DMIP2 Western Basins

Snow cover area affects snowmelt, soil moisture, evapotranspiration, and ultimately streamflow. For the Distributed Model Intercomparison Project - Phase 2 Western basins, we assimilate satellite-based fractional snow cover area (fSCA) from the Moderate Resolution Imaging Spectroradiometer, or MODIS, into the National Weather Service (NWS) SNOW-17 model. This model is coupled with the NWS Sacramento Heat Transfer (SAC-HT) model inside the National Aeronautics and Space Administration's (NASA) Land Information System. SNOW-17 computes fSCA from snow water equivalent (SWE) values using an areal depletion curve. Using a direct insertion, we assimilate fSCAs in two fully distributed ways: 1) we update the curve by attempting SWE preservation, and 2) we reconstruct SWEs using the curve. The preceding are refinements of an existing simple, conceptually-guided NWS algorithm. Satellite fSCA over dense forests inadequately accounts for below-canopy snow, degrading simulated streamflow upon assimilation during snowmelt. Accordingly, we implement a below-canopy allowance during assimilation. This simplistic allowance and direct insertion are found to be inadequate for improving calibrated results, still degrading them as mentioned above. However, for streamflow volume for the uncalibrated runs, we obtain: (1) substantial to major improvements (64-81 %) as a percentage of the control run residuals (or distance from observations), and (2) minor improvements (16-22 %) as a percentage of observed values. We highlight the need for detailed representations of canopy-snow optical radiative transfer processes in mountainous, dense forest regions if assimilation-based improvements are to be seen in calibrated runs over these areas.

Yatheendradas, Soni↗