Search NASA⌕ Search

Engineering topics

Smith, R. E.

Publications and source records attributed to Smith, R. E..

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Engineering Scale Drying of Aluminum-Clad Spent Nuclear Fuel: Experiment Report

Engineering-scale tests were performed to evaluate the relative effectiveness of forced gas and vacuum-drying processes on aluminum-clad spent nuclear fuel (ASNF) in preparation for extended dry storage. Drying models were developed to improve confidence in the likely range of conditions at the start of dry storage and to understand the factors most significant to each process. Testing was performed at the Holtec International Forced Helium Dehydration training facility in Camden, New Jersey, by students from the University of South Carolina in collaboration with Idaho National Laboratory. A full-size Type 1a basket, with a full-diameter vessel configuration (based on the Department of Energy standardized canister design), was used in combination with a 10 assembly surrogate ASNF arrangement to provide a proxy for geometry. A resistance heater incorporated in one assembly simulated the influence of 100 W decay heat. This instrumented chamber allowed testing of the removal of bulk water, physisorbed water, and chemisorbed water over a range of operating parameters with either drying process. Thick oxide films were grown on aluminum test plates to mimic the ASNF surface chemistry. These one-use test plates were housed within select assemblies during drying. Post-test analysis of these plates gave a measure of the moisture removed during each test, which was compared to a control. Instrumentation provided detailed thermal, humidity, and gas or pressure data relevant to each test. Model simulations generally compared favorably to instrument data for the tests. While both processes were able to remove bulk water, removal of chemisorbed water was shown to depend heavily on local temperature. To the disadvantage of vacuum drying, operations approaching or exceeding 220°C achieved consistently more dehydroxylation.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1998

The Marshall Engineering Thermosphere (MET) Model: Technical Description - Volume 1

Volume 1 presents a technical description of the Marshall Engineering Thermosphere (MET) model atmosphere and a summary of its historical development. Various programs developed to augment the original capability of the model are discussed in detail. The report also describes each of the individual subroutines developed to enhance the model. Computer codes for these subroutines are contained in four appendices.

Smith, R. E.↗
NASA NTRS1997

Variational Methods in Design Optimization and Sensitivity Analysis for Two-Dimensional Euler Equations

Variational methods (VM) sensitivity analysis employed to derive the costate (adjoint) equations, the transversality conditions, and the functional sensitivity derivatives. In the derivation of the sensitivity equations, the variational methods use the generalized calculus of variations, in which the variable boundary is considered as the design function. The converged solution of the state equations together with the converged solution of the costate equations are integrated along the domain boundary to uniquely determine the functional sensitivity derivatives with respect to the design function. The application of the variational methods to aerodynamic shape optimization problems is demonstrated for internal flow problems at supersonic Mach number range. The study shows, that while maintaining the accuracy of the functional sensitivity derivatives within the reasonable range for engineering prediction purposes, the variational methods show a substantial gain in computational efficiency, i.e., computer time and memory, when compared with the finite difference sensitivity analysis.

Ibrahim, A. H.↗
NASA NTRS1997

Neutral Orbital Altitude Density Effects on the International Space Station

One of the design requirements of the International Space Station (ISS) is that each year accelerations of one micro-g cannot be exceeded at the ISS internal payload location for 6 periods of not less than 30 consecutive days. Although there are other causes, this study deals only with the accelerations caused by atmospheric drag. The critical ambient neutral density, computed using the Marshall Engineering Thermosphere Model, required to produce accelerations of one micro-g on the ISS, is estimated using an atmospheric drag acceleration equation. Results show that the design requirements may be difficult to meet during periods of extremely high solar activity; the planned reboost and altitude strategies for the ISS may have to be revised to allow for the uncertainty in the prediction of neutral atmospheric density within the 100-day period established for orbital decay before reboost.

Smith, O.E.↗
NASA NTRS1996

Ambient mass density effects on the International Space Station (ISS) microgravity experiments

The Marshall engineering thermosphere model was specified by NASA to be used in the design, development and testing phases of the International Space Station (ISS). The mass density is the atmospheric parameter which most affects the ISS. Under simplifying assumptions, the critical ambient neutral density required to produce one micro-g on the ISS is estimated using an atmospheric drag acceleration equation. Examples are presented for the critical density versus altitude, and for the critical density that is exceeded at least once a month and once per orbit during periods of low and high solar activity. An analysis of the ISS orbital decay is presented.

Smith, O. E.↗
NASA NTRS1995

PIO: A Historical Perspective

These problems relating to Pilot Induced Oscillations have manifested themselves since the earliest days of manned flight. The earliest recorded examples of PIO date back to the Wright brothers first aircraft. The earliest filmed records date back to just prior to World War 2, with the XB-19 aircraft which suffered a pitch PIO just prior to touchdown. Four classes of PIO have been identified, into which all of the known incidents can be grouped. These are: (1) Essentially Single Axis, Extended Rigid Body Effective Vehicle Dynamics; (2) Essentially Single Axis, Extended Rigid Body with Significant Feel-Systern Manipulator Mechanical Control Elements; (3) Multiple Axis, Extended Rigid Body Effective Vehicle Dynamics; and (4) PIO's Involving Higher Frequency Modes.

Mcruer, Duane T.↗
NASA NTRS1992

NASA Workshop on future directions in surface modeling and grid generation

Given here is a summary of the paper sessions and panel discussions of the NASA Workshop on Future Directions in Surface Modeling and Grid Generation held a NASA Ames Research Center, Moffett Field, California, December 5-7, 1989. The purpose was to assess U.S. capabilities in surface modeling and grid generation and take steps to improve the focus and pace of these disciplines within NASA. The organization of the workshop centered around overviews from NASA centers and expert presentations from U.S. corporations and universities. Small discussion groups were held and summarized by group leaders. Brief overviews and a panel discussion by representatives from the DoD were held, and a NASA-only session concluded the meeting. In the NASA Program Planning Session summary there are five recommended steps for NASA to take to improve the development and application of surface modeling and grid generation.

Vandalsem, W. R.↗
NASA NTRS1991

Gridding strategies and associated results for winged entry vehicles

Two volume grid strategies based on similar software are presented for a geometrically complex entry vehicle. It is shown that quick relatively simple grid generation techniques can be used to construct computational grids about entry vehicles with nontrivial geometric complexity. Particular attention is given to both single- and dual-block grid topologies for a lifting body and solution generated on each grid. Results indicate that the grid topology can have an effect on the nature of the solution.

Weilmuenster, K. J.↗
NASA NTRS1991

Grid generation and compressible flow computations about a high-speed civil transport configuration

Techniques and software are discussed for generating grids about a high-speed civil transport configuration. The configuration is defined by a computer-aided design system in wing, fuselage, tail and engine-nacelle components. Grid topology and the surfaces outlining the blocks of the topology are computed with interactive software. The volume grid is computed using software based on transfinite interpolation and Lagrangian blending functions. Several volume grids for inviscid and viscous flow have been generated using this system of codes. Demonstration flowfields around this vehicle are described.

Abolhassani, J. S.↗
NASA NTRS1990

Interpreting the handling qualities of aircraft with stability and control augmentation

The general process of designing an aircraft for good flying qualities is first discussed. Lessons learned are pointed out, with piloted evaluation emerging as a crucial element. Two sources of rating variability in performing these evaluations are then discussed. First, the finite endpoints of the Cooper-Harper scale do not bias parametric statistical analyses unduly. Second, the wording of the scale does introduce some scatter. Phase lags generated by augmentation systems, as represented by equivalent time delays, often cause poor flying qualities. An analysis is introduced which allows a designer to relate any level of time delay to a probability of loss of aircraft control. This view of time delays should, it is hoped, allow better visibility of the time delays in the design process.

Hodgkinson, J.↗
NASA NTRS1990

Surface definition and grid generation about an Assured Crew Return Vehicle (ACRV) for Space Station Freedom

The surface definition and grid generation about an Assured Crew Return Vehicle (ACRV) for the Space Station Freedom are described. The purpose of the surface definition and grid generation is to provide the necessary geometry information for CFD calculations about the vehicle. There are two salient features in this description. The first is that the numerical model representing the ACRV configuration is obtained from the measurement of an existing wind tunnel model. The method for smoothing the measured data and obtaining the numerical model is described. The second feature is the description of the algebraic grid generation method and software to compute volume grids about the ACRV. The methods and software allow rapid computation of volume grids for a wide range of flow conditions.

Smith, R. E.↗
NASA NTRS1988

A conservative approach for flow field calculations on multiple grids

In the computation of flow fields about complex configurations, it is very difficult to construct body-fitted coordinate systems. An alternative approach is to use several grids at once, each of which is generated independently. This procedure is called the 'multiple grids' or 'zonal grids' approach and its applications are investigated in this study. The method follows the conservative approach and provides conservation of fluxes at grid interfaces. The Euler equations are solved numerically on such grids for various configurations. The numerical scheme used is the finite-volume technique with a three-stage Runge-Kutta time integration. The code is vectorized and programmed to run on the CDC VPS-32 computer. Some steady state solutions of the Euler equations are presented and discussed.

Kathong, M.↗
NASA NTRS1988

Application of multiple grids topology to supersonic internal/external flow interactions

For many aerodynamic applications, it is very difficult to construct a smooth body-fitted grid around complex configurations. An approach, called 'multiple grids' or 'zonal grids', which subdivides the entire physical domain into several subdomains, is used to overcome such difficulties. The approach is applied to obtain the solutions to the Euler equations for the supersonic internal/external flow around a fighter-aircraft configuration. Steady-state solutions are presented for Mach 2 at 0, 3.79, 7, and 10 deg angles-of-attack. The problem of conservative treatment at the zonal interfaces is also addressed.

Kathong, M.↗
NASA NTRS1987

Upper and Middle Atmospheric Density Modeling Requirements for Spacecraft Design and Operations

Presented and discussed are concerns with applications of neutral atmospheric density models to space vehicle engineering design and operational problems. The area of concern which the atmospheric model developers and the model users considered, involved middle atmosphere (50 to 90 km altitude) and thermospheric (above 90 km) models and their engineering application. Engineering emphasis involved areas such as orbital decay and lifetime prediction along with attitude and control studies for different types of space and reentry vehicles.

Davis, M. H.↗
NASA NTRS1987

Grid generation and inviscid flow computation about cranked-winged airplane geometries

An algebraic grid generation procedure that defines a patched multiple-block grid system suitable for fighter-type aircraft geometries with fuselage and engine inlet, canard or horizontal tail, cranked delta wing and vertical fin has been developed. The grid generation is based on transfinite interpolation and requires little computational power. A finite-volume Euler solver using explicit Runge-Kutta time-stepping has been adapted to this grid system and implemented on the VPS-32 vector processor with a high degree of vectorization. Grids are presented for an experimental aircraft with fuselage, canard, 70-20-cranked wing, and vertical fin. Computed inviscid compressible flow solutions are presented for Mach 2 at 3.79, 7 and 10 deg angles of attack. Conmparisons of the 3.79 deg computed solutions are made with available full-potential flow and Euler flow solutions on the same configuration but with another grid system. The occurrence of an unsteady solution in the 10 deg angle of attack case is discussed.

Eriksson, L.-E.↗