Search NASA⌕ Search

Engineering topics

Smith, Ryan G.

Publications and source records attributed to Smith, Ryan G..

6 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Catalytic Upgrading of Pyrolysis Condensables from Postconsumer Polyolefins Using HZSM-5

The conversion of plastic wastes to monomeric olefins is an attractive means for achieving a plastic circular economy. In our study, a fluidized bed reactor converts post-consumer waste high-density polyethylene (HDPE) and polypropylene (PP) to mostly condensed pyrolysis waxes and some oils, preventing carbon loss to gases. The pyrolysis condensables were upgraded to light olefins (C 2 –C 5 ) at carbon yields greater than 76 wt % using the HZSM-5 zeolite catalyst at a post pyrolysis process that employed a micropyrolyzer. These results were comparable to olefin monomer yields from direct ex situ catalytic pyrolysis of the original waste plastics without condensing the vapors, highlighting the potential applicability of this approach in plastic waste recycling. Our results suggest that a centralized catalytic upgrading facility fed by pyrolysis condensables sourced from distributed thermochemical processing plants is a promising pathway to a circular economy. Such an approach enables utilization of available catalytic cracking infrastructure while focusing on setting up distributed thermochemical processing plants close to material recovery facilities. As a result, the energy-dense pyrolysis waxes are more suitable for transportation, contributing to the overall scalability and economic viability of the proposed distributed approach.

10 SYNTHETIC FUELS↗
DOE OSTI2024

Structural metamaterials with innate capacitive and resistive sensing

Interpenetrating lattices consist of two or more interwoven but physically separate sub-lattices with unique behaviors derived from their multi-body construction. If the sublattices are constructed or coated with an electrically conducting material, the close proximity and high surface area of the electrically isolated conductors allow the two lattices to interact electromagnetically either across the initial dielectric filled gap or through physical contact. Furthermore, changes in the size of the dielectric gap between the sub-lattices induced by deformation can be measured via capacitance or resistance, allowing a structurally competent lattice to operate as a force or deformation sensor. In addition to resistive and capacitive deformation sensing, this work explores capacitance as a fundamental metamaterial property and the environmental sensing behaviors of interpenetrating lattices.

Computational Solid Mechanics↗
DOE OSTI2024

Increasing pyrolysis oil yields and decreasing energy consumption via thermal oxo-degradation of polyolefins

Commercialization of pyrolysis of plastics in an inert atmosphere is challenging due to large thermal requirements. This study employs thermal oxo-degradation and demonstrates how oxygen supplied at modest equivalence ratios can both accelerate depolymerization and provide the enthalpy for pyrolysis without dramatically impacting desired product yields. The enthalpies for pyrolysis of high-density polyethylene (HDPE) and polypropylene (PP) are measured to be 2,300 ± 90 J g – -1 and 2,800 ± 60 J g –1 , respectively. Using air as an oxygen source in a fluidized bed reactor, HDPE and PP are rapidly deconstructed while using up to 84% less energy through the energy released by partial oxidation. Characterization of the thermal oxo-degradation product oil shows comparable composition to conventional pyrolysis oil. Thermal oxo-degradation proves to be a promising technology for upcycling of plastics by improving thermal depolymerization of waste plastics and reducing energy requirements while maintaining desirable yields.

42 ENGINEERING↗
DOE OSTI2022

Conversion of Phenolic Oil from Biomass Pyrolysis into Phenyl Esters

Bio-oil is among the most economical approaches for advanced biofuel production. However, bio-oil faces several challenges including high acidity and viscosity, poor storage, and thermal stability. This study focuses on the upgradation of lignocellulosic (corn stover and yellow pine) bio-oil derived phenolic oil (PO), produced by the autothermal fast pyrolysis, through acid-catalyzed esterification reaction. Our strategy exploits a little recognized chemistry: the Fischer esterification of PO and carboxylic acids into carboxylic acid phenyl esters (CAPE) using Dean Stark distillation. Analyses by the Folin–Ciocalteu method, Karl Fischer titration, gas chromatography flame ionization detector, and the molecular weight determination by gel permeation chromatography suggest the conversion of 50 wt% added phenolics to their corresponding CAPE. The Fourier transform infrared spectroscopy analysis confirmed the formation of new C=O and two C–O stretching bands and decrease in the intensity of phenolic-OH bands in the CAPE. The 13 C NMR analysis supports the formation of CAPE together with some unreacted precursors. A base-catalyzed ester hydrolysis experiment and mass balance calculation show an excellent agreement (within 5% range) of the equivalent weight between the produced ester and the phenyl hexanoate. Brookfield analysis indicates that CAPE has 330-fold lower viscosity than starting PO. Heating values of CAPE were higher than PO, from which they were derived (42.2 and 43.6%, respectively, for PO from pyrolysis of corn stover and yellow pine), while moisture content decreased by 98.3 and 98.7%, respectively. The CAPE, which is a phenolic analogue of methyl esters used in biodiesel, has improved stability compared to PO from which it was derived.

42 ENGINEERING↗
DOE OSTI2022

CFD-DEM Modeling of Autothermal Pyrolysis of Corn Stover with a Coupled Particle- and Reactor-Scale Framework

Autothermal operation of fast pyrolysis is an efficient process-intensification technique wherein exothermic oxidation reactions are used to overcome the heat-transfer bottleneck of conventional pyrolysis. The development of accurate, reliable modeling toolsets is imperative to generating a deeper understanding of biomass autothermal pyrolysis systems to support scale-up and industrial deployment. This modeling effort describes the development of single-particle and reactor models which incorporate detailed reaction schemes and simultaneous exothermic oxidation reactions. The particle-scale model was parameterized for corn stover feedstock with particle morphology, density, ash content, and biopolymer composition, all of which impact the emergent conversion characteristics during pyrolysis. Results were then used to parameterize a reactor-scale autothermal pyrolysis model, which was developed using a coarse-grained computational fluid dynamic-discrete element method. The simulation results compared well with experimental results, with the predicted bio-oil, light gas, and biochar yield within 3.0 wt% of the experimental yields. Further analyses were performed to test the influence of equivalence ratio, biomass injection position, and particle size distribution on autothermal pyrolysis. The analysis of the physio-chemical properties of the fluid and solid phase inside the reactor and at the reactor outlet help reveal important process interactions of autothermal pyrolysis.

BIOMASS FUELS,INORGANIC, ORGANIC, PHYSICAL, AND AN↗