Engineering topics
Smith, T.
Publications and source records attributed to Smith, T..
Creep, Fatigue and Environmental Interactions and Their Effect on Crack Growth in Superalloys
Complex interactions of creep/fatigue/environment control dwell fatigue crack growth (DFCG) in superalloys. Crack tip stress relaxation during dwells significantly changes the crack driving force and influence DFCG. Linear Elastic Fracture Mechanics, Kmax, parameter unsuitable for correlating DFCG behavior due to extensive visco-plastic deformation. Magnitude of remaining crack tip axial stresses controls DFCG resistance due to the brittle-intergranular nature of the crack growth process. Proposed a new empirical parameter, Ksrf, which incorporates visco-plastic evolution of the magnitude of remaining crack tip stresses. Previous work performed at 704C, extend the work to 760C.
Status of the NPDGamma experiment
We report that the NPDGamma experiment measures the parity-violating (PV) gamma asymmetry from polarized cold neutrons captured on protons at the Spallation Neutron Source (SNS) at Oak Ridge National Laboratory (ORNL). The (PV) neutron spin asymmetry A γ of photons from polarized cold neutron capture on protons is proportional to the ΔI=1 long range weak meson coupling h$1\atop{π}$ between nucleons in the hadronic weak interaction (HWI). Liquid para-hydrogen production data taking concluded in April 2014 and once the background aluminum asymmetry measurements are complete, the PV asymmetry A γ can be extracted. Finally, preliminary results of the analysis of A γ are presented.
Channeling, volume reflection, and volume capture study of electrons in a bent silicon crystal
Not Available
Antifoam Degradation Products in Off Gas and Condensate of Sludge Batch 9 Simulant Nitric-Formic Flowsheet Testing for the Defense Waste Processing Facility
Ten chemical processing cell (CPC) experiments were performed using simulant to evaluate Sludge Batch 9 for sludge-only and coupled processing using the nitric-formic flowsheet in the Defense Waste Processing Facility (DWPF). Sludge Receipt and Adjustment Tank (SRAT) and Slurry Mix Evaporator (SME) cycles were performed on eight of the ten. The other two were SRAT cycles only. Samples of the condensate, sludge, and off gas were taken to monitor the chemistry of the CPC experiments. The Savannah River National Laboratory (SRNL) has previously shown antifoam decomposes to form flammable organic products, (hexamethyldisiloxane (HMDSO), trimethylsilanol (TMS), and propanal), that are present in the vapor phase and condensate of the CPC vessels. To minimize antifoam degradation product formation, a new antifoam addition strategy was implemented at SRNL and DWPF to add antifoam undiluted.
A study of Channeling, Volume Reflection and Volume Capture of 3.35 - 14.0 GeV Electrons in a bent Silicon Crystal
We present the experimental data and analysis of experiments conducted at SLAC National Accelerator Laboratory investigating the processes of channeling, volume-reflection and volume-capture along the (111) plane in a strongly bent quasi-mosaic silicon crystal. Additionally, these phenomena were investigated at 5 energies: 3.35, 4.2, 6.3, 10.5 and 14.0 GeV with a crystal with bending radius of 0.15m, corresponding to curvatures of 0.070, 0.088, 0.13, 0.22 and 0.29 times the critical curvature respectively. We have extracted important parameters describing the channeling process such as the dechanneling length, the angle of volume reflection, the surface transmission and the widths of the distribution of channeled particles parallel and orthogonal to the plane.
C/N and other Elemental Ratios of Chondritic Porous IDPS and a Fluffy Concordia Micrometeorite
Chondritic porous interplanetary dust particles (CP-IDPs) may be cometary in origin [1], as may ultracarbona-ceous (UCAMMs) [2] and 'fluffy' [3] micrometeorites from the Concordia collection. They are all rich in organics, which can rim grains and may have helped glue grains together during accretion [4]. The organics also contain nitrogen the input of which to Earth has potential biological importance. We report C/N ratios, and other properties of CP-IDPs and a Concordia fluffy microme-teorite.
Coordinated Analyses of Mineral-organic Matter Associations in Interplanetary Dust Particles
Little is known about the timing and processes involved in the incorporation of organic matter with inorganic materials in early Solar System bodies. Recently, X-ray absorption near-edge spectroscopy (XANES) studies showed carbon-rich rims surrounding individual mineral grains in anhydrous IDPs [1,2]. These carbonaceous rims are believed to have formed prior to parent body formation and likely served to bond mineral grains during accretion into larger aggregates. We are exploring the nature of these carbonaceous rims through coordinated analyses of their chemistry, mineralogy, spectroscopy and isotopic characteristics. Here we report our preliminary mineralogical observations.
Characterization of 81P/Wild 2 Particles C2067,1,111,6.0 and C2067,1,111,8.0
The concentrations of C and N in cometary particles are of interest in characterizing the regions where comets formed. One aim of this work is to analyze enough Stardust particles to draw meaningful statistical conclusions about their inventories of C and N. Toward that end we report recent studies of Stardust particles and related materials.
Investigation of Long-Term Impacts of Urbanization when Considering Global Warming for a Coastal Tropical Region
The overachieving goal of this project is to gain a better understanding of the climate impacts caused by the combined effects of land cover and land use (LCLU) changes and increasing global concentrations of green house gases (GHG) in tropical coastal areas, regions where global, regional and local climate phenomena converge, taking as the test case the densely populated northeast region of the Caribbean island of Puerto Rico. The research uses an integrated approach of high-resolution remote sensing information linked to a high resolution Regional Atmospheric Modeling System (RAMS), which was employed to perform ensembles of climate simulations (combining 2-LCLU and 2-GHG concentration scenarios). Reconstructed agricultural maps are used to define past LCLU, and combined with reconstructed sea surface temperatures (SST) for the same period form the PAST climate scenario (1951-1956); while the PRESENT scenario (2000-2004) was additionally supported by high resolution remote sensing data (10-m-res). The climate reconstruction approach is validated with available observed climate data from surface weather stations for both periods of time simulated. The selection of the past and present climate scenarios considers large-scale biases (i.e. ENSO/NAO) as reflected in the region of interest. Direct and cross comparison of the results is allowing quantifying single, combined, and competitive effects. Results indicate that global GHG have dominant effects on minimum temperatures (following regional tendencies), while urban sprawl dominates maximum temperatures. To further investigate impacts of land use the Bowen Ratio and the thermal response number (TRN) are analyzed. The Bowen ratio indicates that forestation of past agricultural high areas have an overwhelmingly mitigation effect on increasing temperatures observed in different LCLU scenarios, but when abandoned agricultural lands are located in plains, the resulting shrub/grass lands produce higher surface temperatures. The TRN (J/m^2/degC) is a surface property defined as the ratio of the surface net radiation to the rate of change in surface temperature, expresses how those fluxes are reacting to radiant energy inputs. Natural vegetated surfaces have a greater TRN than urban and barren surfaces because the net radiation processed by them is mostly used for latent heat and thermal storage heat rather than sensible heat (heating the air). Significant changes in TRN were observed in the metropolitan area of San Juan for the two analyzed periods reflecting a reduction of this variable in the present from the past consistent with increasing in thermal mass, or intense urbanization.
Remote Sensing Information Sciences Research Group, Santa Barbara Information Sciences Research Group, year 3
Research continues to focus on improving the type, quantity, and quality of information which can be derived from remotely sensed data. The focus is on remote sensing and application for the Earth Observing System (Eos) and Space Station, including associated polar and co-orbiting platforms. The remote sensing research activities are being expanded, integrated, and extended into the areas of global science, georeferenced information systems, machine assissted information extraction from image data, and artificial intelligence. The accomplishments in these areas are examined.
KBGIS-2: A knowledge-based geographic information system
The architecture and working of a recently implemented knowledge-based geographic information system (KBGIS-2) that was designed to satisfy several general criteria for the geographic information system are described. The system has four major functions that include query-answering, learning, and editing. The main query finds constrained locations for spatial objects that are describable in a predicate-calculus based spatial objects language. The main search procedures include a family of constraint-satisfaction procedures that use a spatial object knowledge base to search efficiently for complex spatial objects in large, multilayered spatial data bases. These data bases are represented in quadtree form. The search strategy is designed to reduce the computational cost of search in the average case. The learning capabilities of the system include the addition of new locations of complex spatial objects to the knowledge base as queries are answered, and the ability to learn inductively definitions of new spatial objects from examples. The new definitions are added to the knowledge base by the system. The system is currently performing all its designated tasks successfully, although currently implemented on inadequate hardware. Future reports will detail the performance characteristics of the system, and various new extensions are planned in order to enhance the power of KBGIS-2.
Detecting Contamination With Photoelectron Emission
Photoelectron emission from aluminum or epoxy-painted aluminum can be used to reveal presence and concentration of surface contaminants. Emission can be used to locate those parts of surface that are excessively contaminated and to which coatings cannot be reliably bonded. Cleaning can then be done on areas that most need it. Probe moves at rate of typically 1 ft/s (30 cm/s), speed slow enough to ensure sensitivity but fast enough to keep scanning time within reasonable limit.
Surface-Contamination Inspection Tool for Field Use
Inspection tool detects surface contamination by measuring photoelectron emission. No vacuum chamber or controlled environment is used. Photoemission is measured under ordinary atmospheric conditions, so surfaces may easily be inspected in factories or in the field.
Residual Silicone Detection
Both photoelectron emission and ellipsometry proved successful in detecting silicone contamination on unpainted and epoxy painted metal surfaces such as those of the external tank and the solid rocket booster. Great success was achieved using photoelectron emission (PEE). Panels were deliberately contaminated to controlled levels and then mapped with PEE to reveal the areas and levels that were contaminated. The panels were then tested with regard to adhesive properties. Tapes were bonded over the contaminated and uncontaminated regions and the peel force was measured, or the contaminated panels were bonded (with CPR 483 foam) to uncontaminated panels and made into lap shear specimens. Other panels were bonded and made into wedge specimens for hydrothermal stress endurance tests. Strong adhesion resulted if the PEE signal fell within an acceptance window, but was poor outside the acceptance window. A prototype instrument is being prepared which can automatically be scanned over the external liquid hydrogen tank and identify those regions that are contaminated and will cause bond degradation.
Peel testing metalized films
Flimsy ultrathin sheets are mounted on glass for peel-strength measurements. Technique makes it easier to perform peel tests on metalized plastic films. Technique was developed for determining peel strength of thin (1,000 A) layers of aluminum on Kapton film. Previously, material has been difficult to test because it is flimsy and tends to curl up and blow away at slightest disturbance. Procedure can be used to measure effects on metalization bond strength of handling, humidity, sunlight, and heat.
Preparing thin aluminum films for adhesive bonding
Carbonate pretreatment produces highly bondable surface without harming film. Treatment is useful in developing low-cost mirrors and solar concentrators fabricated from metal-coated plastic films. Treatment should cost no more than standard degreasing and rinsing procedures.