Engineering topics

Smith, Timothy D.

Publications and source records attributed to Smith, Timothy D..

30 records · Page 2

NASA NTRS2002

Experimental Evaluation of a Subscale Gaseous Hydrogen/gaseous Oxygen Coaxial Rocket Injector

The next generation reusable launch vehicle may utilize a Full-Flow Stage Combustion (FFSC) rocket engine cycle. One of the key technologies required is the development of an injector that uses gaseous oxygen and gaseous hydrogen as propellants. Gas-gas propellant injection provides an engine with increased stability margin over a range of throttle set points. This paper summarizes an injector design and testing effort that evaluated a coaxial rocket injector for use with gaseous oxygen and gaseous hydrogen propellants. A total of 19 hot-fire tests were conducted up to a chamber pressure of 1030 psia, over a range of 3.3 to 6.7 for injector element mixture ratio. Post-test condition of the hardware was also used to assess injector face cooling. Results show that high combustion performance levels could be achieved with gas-gas propellants and there were no problems with excessive face heating for the conditions tested.

Smith, Timothy D.↗

NASA NTRS2002

Status of the RBCC Direct-Connect Mixer Combustor Experiment

The NASA Glenn Research Center is developing hydrogen based combined cycle propulsion technology for a single-stage-to-orbit launch vehicle application under a project called GTX. Rocket Based Combined Cycle (RBCC) propulsion systems incorporate one or more rocket engines into an airbreathing flow path to increase specific impulse as compared to an all rocket-powered vehicle. In support of this effort, an RBCC direct-connect test capability was established at the Engine Components Research Laboratory to investigate low speed, ejector ramjet, and initial ramjet operations and performance. The facility and test article enables the evaluation of two candidate low speed operating schemes; the simultaneous mixing and combustion (SMC) and independent ramjet stream (IRS). The SMC operating scheme is based on the fuel rich operations of the rocket where performance depends upon mixing between the rocket plume and airstream. In contrast, the IRS scheme fuels the airstream separately and uses the rocket plume to ignite the fuel-air mixture. This paper describes the test hardware and facility upgrades installed to support the RBCC tests. It also defines and discusses low speed technical challenges being addressed by the experiments. Finally, preliminary test results, including rocket risk mitigating tests, unfueled airflow tests, and the integrated system hot fire test will be presented.

Walker, James F.↗

NASA NTRS2002

Status of the RBCC Direct-Connect Mixer Combustor Experiment

Walker, James F.↗

NASA NTRS2002

Integrated Nozzle Design for the GTX RBCC Flowpath

The development of rocket based combined cycle (RBCC) engines are highly dependent upon integrating several different modes of operation into a single system. Due to the integrated nature of the propulsion system, each operating mode relies on the same expansion system to provide thrust. A fixed geometry, altitude-compensating aft-expansion configuration is used for the GTX flowpath configuration. Initial studies on the GTX expansion designs have demonstrated the importance of a smooth, highly integrated design for propulsion system performance. Based upon the results from the initial studies, further design improvements were made to the expansion system. Nozzles designed based on both conical and streamline traced flowfields; are discussed. Results from 3-D CFD calculations on an optimized geometry are also presented. A series of cold-flow experiments are proposed to validate the CFD analysis and quantify performance of the flowpath expansions surface design. A discussion is provided of the research hardware designs and experimental test plans.

Smith, Timothy D.↗

NASA NTRS2002

Modes 1 and 4 Testing of an Axisymmetric GTX RBCC Engine

Under sponsorship of the NASA Glenn Research Center (NASA GRC), the Johns Hopkins University Applied Physics Laboratory (JHU/APL) designed and built a five-inch diameter, Rocket-Based Combined Cycle (RBCC) engine to investigate mode 1 and mode 4 performance. This engine was designed so that engine area and length ratios were similar to the NASA GRC GTX engine. Unlike the GTX semi-circular engine design, the APL engine is completely axisymmetric. For this design, a traditional rocket thruster was installed inside of the scramjet flowpath, along the engine centerline. A three part test series is currently underway to determine mode 1 and mode 4 engine performance and compare those results to the rocket thruster operating by itself. All tests are to be conducted in APL's Cell 2 Freejet Engine Facility. Testing of the rocket thruster alone has been accomplished and its performance determined (average Isp efficiency = 90%). Mode 1 (air-augmented rocket) testing is to be conducted at various chamber pressure-to-ambient pressure ratios with the engine inlet fully open. Mode 4 (vacuum rocket) testing is to be conducted with chamber pressure-to-ambient pressure ratios greater than 600 with the inlet fully closed to simulate high-altitude flight conditions. The engine is currently installed in Cell 2 and awaiting testing. This paper discusses the engine design and details the results of the rocket-only testing. Comparisons to previous tests and projected mode 1 and mode 4 test conditions are also discussed.

Rice, Tharen↗

NASA NTRS2001

Hydrogen/Air Fuel Nozzle Emissions Experiments

The use of hydrogen combustion for aircraft gas turbine engines provides significant opportunities to reduce harmful exhaust emissions. Hydrogen has many advantages (no CO2 production, high reaction rates, high heating value, and future availability), along with some disadvantages (high current cost of production and storage, high volume per BTU, and an unknown safety profile when in wide use). One of the primary reasons for switching to hydrogen is the elimination of CO2 emissions. Also, with hydrogen, design challenges such as fuel coking in the fuel nozzle and particulate emissions are no longer an issue. However, because it takes place at high temperatures, hydrogen-air combustion can still produce significant levels of NOx emissions. Much of the current research into conventional hydrocarbon-fueled aircraft gas turbine combustors is focused on NOx reduction methods. The Zero CO2 Emission Technology (ZCET) hydrogen combustion project will focus on meeting the Office of Aerospace Technology goal 2 within pillar one for Global Civil Aviation reducing the emissions of future aircraft by a factor of 3 within 10 years and by a factor of 5 within 25 years. Recent advances in hydrocarbon-based gas turbine combustion components have expanded the horizons for fuel nozzle development. Both new fluid designs and manufacturing technologies have led to the development of fuel nozzles that significantly reduce aircraft emissions. The goal of the ZCET program is to mesh the current technology of Lean Direct Injection and rocket injectors to provide quick mixing, low emissions, and high-performance fuel nozzle designs. An experimental program is planned to investigate the fuel nozzle concepts in a flametube test rig. Currently, a hydrogen system is being installed in cell 23 at NASA Glenn Research Center's Research Combustion Laboratory. Testing will be conducted on a variety of fuel nozzle concepts up to combustion pressures of 350 psia and inlet air temperatures of 1200 F. Computational fluid dynamics calculations, with the Glenn developed National Combustor Code, are being performed to optimize the fuel nozzle designs.

Smith, Timothy D.↗

NASA NTRS2000

Development of an Integrated Nozzle for a Symmetric, RBCC Launch Vehicle Configuration

The development of rocket based combined cycle (RBCC) engines is highly dependent upon integrating several different modes of operation into a single system. One of the key components to develop acceptable performance levels through each mode of operation is the nozzle. It must be highly integrated to serve the expansion processes of both rocket and air-breathing modes without undue weight, drag, or complexity. The NASA GTX configuration requires a fixed geometry, altitude-compensating nozzle configuration. The initial configuration, used mainly to estimate weight and cooling requirements was a 1 So half-angle cone, which cuts a concave surface from a point within the flowpath to the vehicle trailing edge. Results of 3-D CFD calculations on this geometry are presented. To address the critical issues associated with integrated, fixed geometry, multimode nozzle development, the GTX team has initiated a series of tasks to evolve the nozzle design, and validate performance levels. An overview of these tasks is given. The first element is a design activity to develop tools for integration of efficient expansion surfaces With the existing flowpath and vehicle aft-body, and to develop a second-generation nozzle design. A preliminary result using a "streamline-tracing" technique is presented. As the nozzle design evolves, a combination of 3-D CFD analysis and experimental evaluation will be used to validate the design procedure and determine the installed performance for propulsion cycle modeling. The initial experimental effort will consist of cold-flow experiments designed to validate the general trends of the streamline-tracing methodology and anchor the CFD analysis. Experiments will also be conducted to simulate nozzle performance during each mode of operation. As the design matures, hot-fire tests will be conducted to refine performance estimates and anchor more sophisticated reacting-flow analysis.

Smith, Timothy D.↗

NASA NTRS1999

High-Area-Ratio Rocket Nozzle at High Combustion Chamber Pressure: Experimental and Analytical Validation

Experimental data were obtained on an optimally contoured nozzle with an area ratio of 1025:1 and on a truncated version of this nozzle with an area ratio of 440:1. The nozzles were tested with gaseous hydrogen and liquid oxygen propellants at combustion chamber pressures of 1800 to 2400 psia and mixture ratios of 3.89 to 6.15. This report compares the experimental performance, heat transfer, and boundary layer total pressure measurements with theoretical predictions of the current Joint Army, Navy, NASA, Air Force (JANNAF) developed methodology. This methodology makes use of the Two-Dimensional Kinetics (TDK) nozzle performance code. Comparisons of the TDK-predicted performance to experimentally attained thrust performance indicated that both the vacuum thrust coefficient and the vacuum specific impulse values were approximately 2.0-percent higher than the turbulent prediction for the 1025:1 configurations, and approximately 0.25-percent higher than the turbulent prediction for the 440:1 configuration. Nozzle wall temperatures were measured on the outside of a thin-walled heat sink nozzle during the test fittings. Nozzle heat fluxes were calculated front the time histories of these temperatures and compared with predictions made with the TDK code. The heat flux values were overpredicted for all cases. The results range from nearly 100 percent at an area ratio of 50 to only approximately 3 percent at an area ratio of 975. Values of the integral of the heat flux as a function of nozzle surface area were also calculated. Comparisons of the experiment with analyses of the heat flux and the heat rate per axial length also show that the experimental values were lower than the predicted value. Three boundary layer rakes mounted on the nozzle exit were used for boundary layer measurements. This arrangement allowed total pressure measurements to be obtained at 14 different distances from the nozzle wall. A comparison of boundary layer total pressure profiles and analytical predictions show good agreement for the first 0.5 in. from the nozzle wall; but the further into the core flow that measurements were taken, the more that TDK overpredicted the boundary layer thickness.

Jankovsky, Robert S.↗

NASA NTRS1998

Parametric Study Conducted of Rocket- Based, Combined-Cycle Nozzles

Having reached the end of the 20th century, our society is quite familiar with the many benefits of recycling and reusing the products of civilization. The high-technology world of aerospace vehicle design is no exception. Because of the many potential economic benefits of reusable launch vehicles, NASA is aggressively pursuing this technology on several fronts. One of the most promising technologies receiving renewed attention is Rocket-Based, Combined-Cycle (RBCC) propulsion. This propulsion method combines many of the efficiencies of high-performance jet aircraft with the power and high-altitude capability of rocket engines. The goal of the present work at the NASA Lewis Research Center is to further understand the complex fluid physics within RBCC engines that govern system performance. This work is being performed in support of NASA's Advanced Reusable Technologies program. A robust RBCC engine design optimization demands further investigation of the subsystem performance of the engine's complex propulsion cycles. The RBCC propulsion system under consideration at Lewis is defined by four modes of operation in a singlestage- to-orbit configuration. In the first mode, the engine functions as a rocket-driven ejector. When the rocket engine is switched off, subsonic combustion (mode 2) is present in the ramjet mode. As the vehicle continues to accelerate, supersonic combustion (mode 3) occurs in the ramjet mode. Finally, as the edge of the atmosphere is approached and the engine inlet is closed off, the rocket is reignited and the final accent to orbit is undertaken in an all-rocket mode (mode 4). The performance of this fourth and final mode is the subject of this present study. Performance is being monitored in terms of the amount of thrust generated from a given amount of propellant.

Steffen, Christopher J., Jr.↗

NASA NTRS1998

Performance of an Axisymmetric Rocket Based Combined Cycle Engine During Rocket Only Operation Using Linear Regression Analysis

The all rocket mode of operation is shown to be a critical factor in the overall performance of a rocket based combined cycle (RBCC) vehicle. An axisymmetric RBCC engine was used to determine specific impulse efficiency values based upon both full flow and gas generator configurations. Design of experiments methodology was used to construct a test matrix and multiple linear regression analysis was used to build parametric models. The main parameters investigated in this study were: rocket chamber pressure, rocket exit area ratio, injected secondary flow, mixer-ejector inlet area, mixer-ejector area ratio, and mixer-ejector length-to-inlet diameter ratio. A perfect gas computational fluid dynamics analysis, using both the Spalart-Allmaras and k-omega turbulence models, was performed with the NPARC code to obtain values of vacuum specific impulse. Results from the multiple linear regression analysis showed that for both the full flow and gas generator configurations increasing mixer-ejector area ratio and rocket area ratio increase performance, while increasing mixer-ejector inlet area ratio and mixer-ejector length-to-diameter ratio decrease performance. Increasing injected secondary flow increased performance for the gas generator analysis, but was not statistically significant for the full flow analysis. Chamber pressure was found to be not statistically significant.

Smith, Timothy D.↗

NASA NTRS1995

Ablative material testing for low-pressure, low-cost rocket engines

The results of an experimental evaluation of ablative materials suitable for the production of light weight, low cost rocket engine combustion chambers and nozzles are presented. Ten individual specimens of four different compositions of silica cloth-reinforced phenolic resin materials were evaluated for comparative erosion in a subscale rocket engine combustion chamber. Gaseous hydrogen and gaseous oxygen were used as propellants, operating at a nominal chamber pressure of 1138 kPa (165 psi) and a nominal mixture ratio (O/F) of 3.3. These conditions were used to thermally simulate operation with RP-1 and liquid oxygen, and achieved a specimen throat gas temperature of approximately 2456 K (4420 R). Two high-density composition materials exhibited high erosion resistance, while two low-density compositions exhibited approximately 6-75 times lower average erosion resistance. The results compare favorably with previous testing by NASA and provide adequate data for selection of ablatives for low pressure, low cost rocket engines.

Richter, G. Paul↗

NASA NTRS1993

Design and fabrication of a hydrogen/oxygen thrust chamber assembly

The combustion system for the Advance Expander Test Bed engine consists of a thrust mount, an injector with a H2-O2 torch igniter, a combustion chamber, and a conical nozzle extension. These components constitute the thrust chamber assembly. The design, fabrication, and testing of these components are described in detail.

Hernacki, Thomas R.↗