Search NASA⌕ Search

Engineering topics

Smith, Timothy M.

Publications and source records attributed to Smith, Timothy M..

11 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Dissolution zone model of the oxide structure in additively manufactured dispersion-strengthened alloys

The structural evolution of oxides in dispersion-strengthened superalloys during laser-powder bed fusion is considered in detail. Alloy chemistry and process parameter effects on oxide structure are assessed through a parameter study on the model alloy Ni-20Cr, doped with varying concentrations of Y 2 O 3 and Al. Small angle neutron scattering measurements of the dispersoid size distribution show the dispersoid size increases with higher laser power, slower scan speed, and increasing Y 2 O 3 and Al content. Complementary electron microscopy measurements reveal reactions between Y 2 O 3 and Al, even in nanoscale dispersoids, and the presence of micron-scale oxide slag inclusions in select specimens. A scaling analysis of mass and momentum transport within the melt pool, presented here, establishes that diffusional structural evolution mechanisms dominate for nanoscale dispersoids, while fluid forces and advection become significant for larger slag inclusions. These findings are developed into a theory of dispersoid structural evolution, integrating quantitative models of diffusional processes – dispersoid dissolution, nucleation, growth, coarsening – with a reduced order model of time-temperature trajectories of fluid parcels within the melt pool. Calculations of the dispersoid size in single-pass melting reveal a zone in the center of the melt track in which the oxide feedstock fully dissolves. Within this zone the final Y 2 O 3 size is independent of feedstock size and determined by nucleation and growth kinetics. If the dissolution zones of adjacent melt tracks overlap sufficiently with each other to dissolve large oxides, formed during printing or present in the powder feedstock, then the dispersoid structure throughout the build volume is homogeneous and matches that from a single pass within the dissolution zone. Gaps between adjacent dissolution zones result in oxide accumulation into larger slag inclusions. Predictions of final dispersoid size and slag formation using this dissolution zone model match the present experimental data and explain process-structure linkages speculated in the open literature.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Quantifying nitrogen loss hotspots and mitigation potential for individual fields in the US Corn Belt with a metamodeling approach

The high productivity in the US Corn Belt is largely enabled by the consumption of millions of tons of manufactured fertilizer. Excessive application of nitrogen (N) fertilizer has been pervasive in this region, and the unrecovered N eventually escaped from croplands in forms of nitrous oxide (N 2 O) emission and N leaching. Mitigating these negative impacts is hindered by a lack of practical information on where to focus and how much mitigation potential to expect. At a large scale, process-based crop models are the primary tools for predicting variables required by decision making, but their applications are prohibited by expensive computational and data storage costs. To overcome these challenges, we built a series of metamodels to learn the key mechanisms regarding the carbon (C) and N cycle from a well-validated process-based biogeochemical model, ecosys. The trained metamodel captures over 98% of the variability of the ecosys simulated outputs for 99 randomly selected counties in Iowa, Illinois, and Indiana. To identify hotspots with high mitigation potential, we introduce net societal benefit (NSB) as an indicator for synthesizing the loss in yield and social benefits through emissions and pollutants avoided. Our results show that reducing N fertilizer by 10% leads to 9.8% less N 2 O emissions and 9.6% less N leaching at the cost of 4.9% more SOC depletion and 0.6% yield reduction over the study region. The estimated total annual NSB is $\$395$ M (uncertainty ranges from $\$114$ M to $\$1271$ M), including $\$334$ from social benefits (uncertainty ranges from $\$46$ M to $\$1076$ M), $\$100$ M from saving fertilizer (uncertainty ranges from $\$13$ M to $\$455$ M), and –$\$40$ M due to yield changes (uncertainty ranges from –$\$261$ M to $\$69$ M). For the median scenario, we noted that 20% of the study area accounts for nearly 50% of the NSB, and thus represent hotspot locations for targeted mitigation. Although the uncertainty range suggests that developing such a high-resolution framework is not yet settled and the scenario based estimations are not appropriate to inform the management practices for individual farmers, our efforts shed light on the new generation of analytical tools for life cycle assessment.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS2020

Producing Next Generation Superalloys Through Advanced Characterization and Manufacturing Techniques

NASA is currently working towards developing the next generation high temperature alloys for various aerospace and energy applications. Through advanced microscopy and computational insights, a novel atomic scale strengthening mechanism was discovered in Ni-base superalloys. This new local phase transformation strengthening technique has been successfully implemented resulting in new disk alloys with substantial improvements in creep strength over current state-of-the-art. Furthermore, additive manufacturing has been leveraged to produce dispersion strengthened (DS), multi-principal element alloys (MPEA) without the use of traditional mechanical alloying or chemical reactions. This new processing technique has successfully resulted in 99.9% dense oxide dispersion strengthened NiCoCr alloy parts. High temperature mechanical testing of the DS alloys showed significant improvements in strength and ductility over the baseline NiCoCr. As a result, this recently discovered processing route opens a new alloy design and production path that is synergistic between additive manufacturing and dispersion strengthening, possibly enabling a new generation of high-performance alloys.

Smith, Timothy M.↗
NASA NTRS2019

Investigation of Stacking Fault and Antiphase Boundary Segregation in Ni-Based Superalloys Using Density Functional Theory

Ni-base superalloys have a long history of use in jet turbine engines, and efforts to improve their performance in that application are ongoing. It is known that the precipitation of the Ni3Al γ' phase within the disordered FCCγ phase strengthens the overall material. However, in the high-temperature environment found inside a turbine engine during operation, creep can cause the γ' phase to transform to different, weaker phases along stacking faults, leading to a deterioration of performance. In the γ' phase one mode of creep deformation is the formation of stacking fault ribbons, which consist of intrinsic stacking faults further shearing into antiphase boundaries (APBs). It is also known that certain alloying additions exhibit segregation to stacking faults. If segregating elements could be identified which segregate to the intrinsic stacking fault, but not to the APB, the inclusion of such elements could lead to improved creep strength in these alloys. To investigate this possibility, a density functional investigation of the segregation of W, Mo and Cr to both a superlattice intrinsic stacking fault (SISF) and an APB was performed. It was found that W, Mo and Cr all exhibit segregation to the SISF. In contrast, for the APB, Cr was either energy-neutral, or segregates, depending on the presence of additional nearby Cr, or on the specific lattice site upon which it was placed, while Mo and W did not segregate. Because W and Mo segregate to the SISF but not to the APB, the inclusion of these elements could provide a degree of protection against creep-related deterioration.

Good, Brian S.↗
NASA NTRS2019

The Effect Stacking Fault Segregation and Phase Transformations have on Creep Strength in Ni-based Superalloys

In this study, two commercially similar polycrystalline Ni-based disk superalloys (LSHR and ME3) were creep tested at 760C and 552MPa to approximately 0.3% plastic strain. LSHR consistently displayed superior creep properties at this stress/temperature regime even though the microstructural characteristics between the two alloys were comparable. High resolution structural and chemical analysis, however, revealed significant differences between the two alloys among active gamma prime shearing modes involving superlattice intrinsic and extrinsic stacking faults. In ME3, Co and Cr segregation and Ni and Al depletion were observed along the intrinsic faults - revealing a gamma prime -to- gamma phase transformation. Conversely in LSHR, an alloy with a higher W content, Co and W segregation was observed along the intrinsic faults. This observation combined with scanning transmission electron microscopy (STEM) simulations confirm a gamma prime-to-D019 phase transformation along the intrinsic faults in LSHR. Using experimental observations and density functional theory calculations, a novel local phase transformation strengthening mechanism is proposed that could be further utilized to improve the high temperature creep capabilities of Ni-base disk alloys.

Superalloy↗
NASA NTRS2018

Impact of Powder Variability on the Microstructure and Mechanical Behavior of Selective Laser Melted (SLM) Alloy 718

Nickel Alloy 718 has found wide use in high-temperature aerospace applications (up to 700°C), due to a combination of good mechanical properties, environmental resistance, and workability at moderate cost. These properties have led Alloy 718 to early adoption by selective laser melting (SLM) additive manufacturing. This presentation will share results from a comprehensive industry survey of 718 powder feedstock for SLM. The survey focuses on the impact of variability in powder characteristics on build quality, microstructure, tensile and high cycle fatigue in the as-fabricated and machined surface conditions. The investigation includes sixteen powder lots from eight suppliers that are produced by gas atomization or rotary atomization in argon or nitrogen. This research was previously presented and published at the 9th International Symposium on Superalloy 718 & Derivatives and was funded by NASA Space Launch System Liquid Engine Office with the Human Exploration Operations Mission Directorate.

Sudbrack, Chantal↗
NASA NTRS2018

Impact of Powder Variability on the Microstructure and Mechanical Behavior of Selective Laser Melted Alloy 718

Powder-bed additive manufacturing processes use fine powders to build parts layer-by-layer. Alloy 718 powder feedstocks for selective laser melting (SLM) additive manufacturing are produced commercially by both gas and rotary atomization and are available typically in the 10-45 or 15-45 microns size ranges. A comprehensive investigation was conducted to understand the impact of powder variability on the microstructure and mechanical behavior of SLM 718 heat treated to Aerospace Material Specification (AMS) 5664. This study included sixteen virgin powders and three once-recycled powders within the 10-45 and 15-45 microns size ranges that were obtained from seven direct source suppliers and one reseller. Although alike as highly regular spheroids, these powders showed distinct differences in composition (especially Al, C and N contents), particle size distributions, and powder features such as degree of agglomeration, fusion and surface roughness. Compositional differences expectedly had the strongest impact on microstructure. High N and C contents formed TiN-nitrides and/or (Nb,Ti,Mo)-C carbides on the grain boundaries, prevented recrystallization during heat treatment, and resulted in retained (001)-scalloped shaped grains that ranged from 19 to 41 microns in average size. In the absence of this particle pinning, the average grain size of the heat treated SLM 718 ranged from 51 microns to 90 microns. Room temperature tensile and high cycle fatigue (HCF) testing compared as-fabricated (AF) and low stress ground (LSG) surface conditions. Tensile testing revealed consistent behavior between the two surface conditions and amongst the powder lots. The finer grained SLM 718 builds displayed the lowest tensile properties. A SLM 718 build fabricated from a powder with eight times lower C content showed statistically better tensile properties presumably due to enhanced coarsening of (delta)-Ni3Nb precipitates. The specimens from once-recycled powders had slightly higher tensile strengths and slightly higher ductility compared to their virgin equivalents; once-recycling also did not substantially degrade the mean HCF life. The LSG fatigue lives agreed with conventionally manufactured 718 data, while AF lives exhibited a knock-down due to surface roughness. The fatigue lives of AF specimens were statistically equivalent across powder lots except for one and failures typically initiated at stress concentrators associated with SLM surface asperities. Fatigue testing of low stress ground specimens result in both transgranular and within facet crack initiations. More than half of the cracks initiated from these facets for the machined condition; however, these facets appeared to be within grains that were larger-than-average in size. A nitrogen-atomized powder with fine prior particles of TiN-nitrides and M(Ti,Nb,Mo)C carbides from atomization on powder surfaces resulted in the best fatigue performance with segregation of these particles to the SLM 718 grain boundaries leading to higher resistance to early-stage crack propagation. Typically the fine-grained builds with minor phases along the grain boundaries did not perform well in fatigue, whereas a larger-grain build with lower carbon content and coarser delta-Ni3Nb precipitates showed the next best HCF response. Further details of the build microstructure and its impact on tensile and fatigue behavior was considered.

laser deposition↗
NASA NTRS2017

Relationship Between Unusual High-Temperature Fatigue Crack Growth Threshold Behavior in Superalloys and Sudden Failure Mode Transitions

An investigation of high temperature cyclic fatigue crack growth (FCG) threshold behavior of two advanced nickel disk alloys was conducted. The focus of the study was the unusual crossover effect in the near-threshold region of these type of alloys where conditions which produce higher crack growth rates in the Paris regime, produce higher resistance to crack growth in the near threshold regime. It was shown that this crossover effect is associated with a sudden change in the fatigue failure mode from a predominant transgranular mode in the Paris regime to fully intergranular mode in the threshold fatigue crack growth region. This type of a sudden change in the fracture mechanisms has not been previously reported and is surprising considering that intergranular failure is typically associated with faster crack growth rates and not the slow FCG rates of the near-threshold regime. By characterizing this behavior as a function of test temperature, environment and cyclic frequency, it was determined that both the crossover effect and the onset of intergranular failure are caused by environmentally driven mechanisms which have not as yet been fully identified. A plausible explanation for the observed behavior is proposed.

Fatigue Crack Growth Thresholds; Grain boundary ox↗