Engineering topics

Somers, D. M.

Publications and source records attributed to Somers, D. M..

14 records

NASA NTRS1982

Influence of surface static-pressure orifices on boundary-layer transition

An investigation of the interaction of a laminar boundary layer and surface static-pressure orifices was conducted on a natural laminar flow airfoil. The effects of both favorable and adverse pressure gradients were studied at Reynolds numbers based on airfoil chord from approximately 500,000 to 6,000,000 with Mach number varying accordingly from about 0.03 to 0.42. The smaller the diameter of the orifice, the less likely it will cause premature transition. Locating the orifices in a chord-wise row aligned with the flow appears to have an additive, adverse effect on transition. Tube length-to-orifice diameter ration does not seem to have a consistent influence on transition.

Somers, D. M.↗

NASA NTRS1981

Design and Experimental Results for a Natural-Laminar-Flow Airfoil for General Aviation Applications

A natural-laminar-flow airfoil for general aviation applications, the NLF(1)-0416, was designed and analyzed theoretically and verified experimentally in the Langley Low-Turbulence Pressure Tunnel. The basic objective of combining the high maximum lift of the NASA low-speed airfoils with the low cruise drag of the NACA 6-series airfoils was achieved. The safety requirement that the maximum lift coefficient not be significantly affected with transition fixed near the leading edge was also met. Comparisons of the theoretical and experimental results show excellent agreement. Comparisons with other airfoils, both laminar flow and turbulent flow, confirm the achievement of the basic objective.

Somers, D. M.↗

NASA NTRS1981

Design and experimental results for a flapped natural-laminar-flow airfoil for general aviation applications

A flapped natural laminar flow airfoil for general aviation applications, the NLF(1)-0215F, has been designed and analyzed theoretically and verified experimentally in the Langley Low Turbulence Pressure Tunnel. The basic objective of combining the high maximum lift of the NASA low speed airfoils with the low cruise drag of the NACA 6 series airfoils has been achieved. The safety requirement that the maximum lift coefficient not be significantly affected with transition fixed near the leading edge has also been met. Comparisons of the theoretical and experimental results show generally good agreement.

Somers, D. M.↗

NASA NTRS1981

The design and analysis of low-speed airfoils

PROFILE program solves diverse and inverse airfoil-flow problems. It combines conformational mapping method for design of airfoils with prescribed velocity-distribution characteristics, panel method for potential-flow analysis, and boundary-layer method. PROFILE is written in FORTRAN IV for implementation on CDC 6000-series computer.

Eppler, R.↗

NASA NTRS1981

NASA research related to sailplane airfoils

The theoretical methods and experimental facilities at the NASA Langley Research Center have been employed to conduct investigations of sailplane airfoils. The unique and powerful capabilities of the Eppler Program have been used to design and analyze many airfoils and to smooth several Wortmann airfoils. Wind-tunnel investigations of two sailplane airfoils have been conducted in the Langley low-turbulence pressure tunnel. A procedure for sailplane performance improvement has been outlined.

Somers, D. M.↗

NASA NTRS1980

A computer program for the design and analysis of low-speed airfoils, supplement

Three new options were incorporated into an existing computer program for the design and analysis of low speed airfoils. These options permit the analysis of airfoils having variable chord (variable geometry), a boundary layer displacement iteration, and the analysis of the effect of single roughness elements. All three options are described in detail and are included in the FORTRAN IV computer program.

Eppler, R.↗

NASA NTRS1980

A computer program for the design and analysis of low-speed airfoils

A conformal mapping method for the design of airfoils with prescribed velocity distribution characteristics, a panel method for the analysis of the potential flow about given airfoils, and a boundary layer method have been combined. With this combined method, airfoils with prescribed boundary layer characteristics can be designed and airfoils with prescribed shapes can be analyzed. All three methods are described briefly. The program and its input options are described. A complete listing is given as an appendix.

Eppler, R.↗

NASA NTRS1979

An exploratory investigation of the effect of a plastic coating on the profile drag of a practical-metal-construction sailplane airfoil

The Langley low-turbulence pressure tunnel to determine the effect of a plastic coating on the profile drag of a practical-metal-construction sailplane airfoil was investigated. The model was tested with three surface configurations: (1) filled, painted, and sanded smooth; (2) rough bare metal; and (3) plastic-coated. The results are compared with data for the design airfoil (Wortmann FX 67-K-170/17) from another low-turbulence wind tunnel. The investigation was conducted at Reynolds numbers based on airfoil chord of 1.1 x 10 to the 6th power, 2.2 x 10 to the 6th power, and 3.3 x 10 to the 6th power at a Mach number of 0.10.

Somers, D. M.↗

NASA NTRS1979

Low speed airfoil design and analysis

A low speed airfoil design and analysis program was developed which contains several unique features. In the design mode, the velocity distribution is not specified for one but many different angles of attack. Several iteration options are included which allow the trailing edge angle to be specified while other parameters are iterated. For airfoil analysis, a panel method is available which uses third-order panels having parabolic vorticity distributions. The flow condition is satisfied at the end points of the panels. Both sharp and blunt trailing edges can be analyzed. The integral boundary layer method with its laminar separation bubble analog, empirical transition criterion, and precise turbulent boundary layer equations compares very favorably with other methods, both integral and finite difference. Comparisons with experiment for several airfoils over a very wide Reynolds number range are discussed. Applications to high lift airfoil design are also demonstrated.

Eppler, R.↗

NASA NTRS1979

An Exploratory Investigation of the Effect of Plastic Coating on the Profile Drag of a Practical-Metal-Construction Sailplane Airfoil

An exploratory investigation was performed in the Langley low-turbulence pressure tunnel to determine the effect of a plastic coating on the profile drage of a practical-metal-construction sailplaine airfoil. The mode was tested with three surface configurations: (1) filled, painted, and sanded smooth; (2) rough bare metal; and (3) plastic-coated. The investigation was conducted at Reynolds numbers based on airfoil chord of 1,100,000, 2,200,000, and 3,300,000 at a constant Mach number of 0.10. The results indicate that, at all three Reynolds numbers, the order of the drag values of the three surface configurations, starting with the highest drag, was: filled, painted, and sanded smooth; rough bare metal; and plastic-coated.

Somers, D. M.↗

NASA NTRS1979

The application of microprocessor technology to in-flight computation

A modular design of a general purpose microprocessor-based computer to perform in-flight computations for cross-country soaring pilots is described. The basic requirements for the system are discussed. Several specialized applications of the computer are presented, including real-time pilot feedback and flight-test data acquisition and reduction.

Sawyer, P. L.↗

NASA NTRS1978

Detection of boundary-layer transitions in wind tunnels

Accelerometer replaces stethoscope in technique for detection of laminar-to-turbulent boundary-layer transitions on wind-tunnel models. Technique allows measurements above or below atmospheric pressure because human operator is not required within tunnel. Data may be taken from accelerometer, and pressure transducer simultaneously, and delivered to systems for analysis.

Wood, W. R.↗

NASA NTRS1977

Experimental and theoretical low-speed aerodynamic characteristics of a Wortmann airfoil as manufactured on a fiberglass sailplane

A low turbulence pressure tunnel evaluation is reported for low speed aerodynamic characteristics of the FX 66-17AII-182 airfoil as manufactured on a fiberglass sailplane. The results were compared with data for design coordinates obtained from another low turbulence wind tunnel and with theoretical calculations generated by a viscous flow airfoil computer program. The investigation was performed over a Reynolds number range, based on airfoil chord, of approximately 0.5 x 1 million to 6 million and a Mach number range of about 0.05 to 0.35. Comparison with data from another wind tunnel for the design coordinates showed slightly higher drag for the manufactured section.

Somers, D. M.↗

NASA NTRS1975

Low-speed aerodynamic characteristics of a 13-percent-thick airfoil section designed for general aviation applications

Wind-tunnel tests were conducted to determine the low-speed section characteristics of a 13 percent-thick airfoil designed for general aviation applications. The results were compared with NACA 12 percent-thick sections and with the 17 percent-thick NASA airfoil. The tests were conducted ovar a Mach number range from 0.10 to 0.35. Chord Reynolds numbers varied from about 2,000,000 to 9,000,000.

Mcghee, R. J.↗