Exploring the Synthesis of Alkali Metal Anti-perovskites
Explore the source record for details and available documents.
Kim, Kwangnam↗
Engineering topics
Son, Seoung-Bum
Publications and source records attributed to Son, Seoung-Bum.
Understanding the constant-voltage fast-charging process using a high-rate Ni-rich cathode material for lithium-ion batteries
This study proposes constant-voltage charging as a promising fast-charging protocol and reveals the origin of capacity degradation in constant-voltage charging.
Ku, Kyojin↗
Effect of cathode on crosstalk in Si-based lithium-ion cells
Crosstalk between the cathode and the anode in Li-ion batteries has a great impact on performance, safety and cycle lifetime. However, a systematic investigation of crosstalk behavior in silicon (Si)-based cells with various cathode materials has not been reported. We investigated the crosstalk behavior of a Si anode coupled with one of the following cathodes—LiCoO 2 (LCO), LiNi 0.5 Mn 0.3 Co 0.2 (NMC532), and LiFePO 4 (LFP)—in a full cell. For each electrochemical couple, we compared electrolyte decomposition products, solid electrolyte interphase (SEI) chemistry, and degradation mechanisms during cycling. From a very early stage of cycling, each couple showed different crosstalk behavior; different electrolyte decomposition products and SEI chemistry on the Si anodes were seen. Specifically, the formation and growth mechanism of Si SEI differ depending on cathode materials. For the LFP system, the Si SEI rich in LiF and inorganic species, which is stable and robust. It forms at an early stage of cycle. As a result, the SEI of Si from the LFP system well tolerates SEI breakage due to mechanical changes of Si and suppresses Li loss, resulting in stable cycle life.
25 ENERGY STORAGE↗
Recycled cathode materials enabled superior performance for lithium-ion batteries
Not Available
25 ENERGY STORAGE↗
Methodologies for Design, Characterization and Testing of Electrolytes that Enable Extreme Fast Charging of Lithium-ion Cells
Selection, testing and validation of electrolyte candidates for Li-ion cells are discussed, based on a 10-minute target for extreme fast charge (XFC). A combination of modeling and laboratory measurements create a timely and synergistic approach to identifying candidate electrolyte formulations. Multi-solvent systems provide a balanced set of properties, wherein lower molecular-weight solvents offer reduced viscosity, increased species diffusivity, and mitigation of concentration polarization at high charge rates. Carefully selected formulations can exhibit peak conductivity and usable conductivity range of two to three times that of the baseline EC-EMC (3:7, wt.) + LiPF 6 . Candidates are also chosen based on stability and longevity within the cell environment. Lab testing coincides with property predictions from the Advanced Electrolyte Model (AEM) and a macro-scale cell model. Furthermore, cell testing utilized coin and pouch cells having NMC532 or NMC811 cathodes with graphite electrodes. Results indicate combinations of low-molecular weight solvents are key for fast-charge electrolytes as they extend the useful conductivity range to both low and higher salt concentrations, and possess higher self-diffusivities compared to conventional solvents. This reduces impacts from concentration polarization. The choice of electrolyte also influences the tendency for lithium metal deposition at the anode, as showcased by experimental and modeling results herein.
25 ENERGY STORAGE↗
Dual-Salt Electrolytes to Effectively Reduce Impedance Rise of High-Nickel Lithium-Ion Batteries
Simply mixing several lithium salts in one electrolyte to obtain blended salt electrolytes has been demonstrated as a promising strategy to formulate advanced electrolytes for lithium metal batteries (LMBs) and lithium-ion batteries (LIBs). In this study, we report the use of dual-salt electrolytes containing lithium hexafluorophosphate (LiPF6) and lithium difluorophosphate (LiDFP) in ethylene carbonate/ethyl methyl carbonate (EC/EMC) mixture and tested them in layered high-nickel LIB cells. LiNi 0.94 Co 0.06 O 2 was synthesized through a coprecipitation method and was used as a representative high-nickel cathode for the U.S. DOE realizing next-generation cathode (RNGC) deep dive program. The ionic conductivity of dual-salt electrolytes can be maintained by controlling the amount of LiDFP. Techniques including 1 H Nuclear Magnetic Resonance (NMR), X-ray photoelectron spectroscopy (XPS), inductively coupled plasma-mass spectrometry (ICP-MS), and differential voltage analysis (DVA) were used to understand the improved performance. Additionally, the multifaceted benefits of using the dual-salt electrolytes include (1) reduced transesterification, (2) formation of a stable cathode electrolyte interface, and (3) mitigation of cathode degradation at high voltages, especially stabilization of oxide particles during the H 2 <-> H 3 transformation.
25 ENERGY STORAGE↗
Magnesium metal devices and methods of making the same
The present disclosure relates to a device that includes a first electrode, where the first electrode includes magnesium metal having a first surface, and a first coating in physical contact with the first surface and covering substantially all of the first surface, where the first coating has a first thickness, and the first coating is configured to transport a plurality of magnesium ions through the first thickness, such that a first portion of the plurality of magnesium ions are reversibly depositable as elemental magnesium onto the first surface.
Ban, Chunmei↗
In Situ Localized Polysulfide Injector for the Activation of Bulk Lithium Sulfide
The activation of commercial Li 2 S remains to be one of the key challenges against its commercialization as a starting cathode material for a sulfur-based Li-ion battery system. In this work we take advantage of the lower oxidation potential of commercial Na 2 S (1–3 wt%) to serve as an in situ and local polysulfide injector for the activation of commercial Li 2 S (70 wt%). Furthermore, in contrast to applying pre-solvated redox mediators, this technique allows for the activation of commercial Li 2 S at lower voltages with an electrolyte content as low as 3 μL mg –1 Li 2 S at 3 mgmg Li 2 S cm –2 and 4 μL mg –1 Li 2 S at 6.5 mg Li 2 S cm –2 without any other material modification.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
How Fast Can a Li-Ion Battery Be Charged? Determination of Limiting Fast Charging Conditions
Fast-charge protocols that prevent lithium plating are needed to extend the life span of lithium-ion batteries. Here, we describe a simple experimental method to estimate the minimum charging time below which it is simply impossible to avoid plating at a given temperature. We demonstrate that, by gauging and correcting the ohmic drop that is intrinsic to reference electrodes, the local potential at the anode surface can be reasonably approximated. This finer anode control enables the determination of the maximum average rate at which lithium deposition can be mitigated, establishing realistic boundaries that can inform the development of advanced charging protocols.
25 ENERGY STORAGE↗
Systematic Study of the Cathode Compositional Dependency of Cross-Talk Behavior in Li-Ion Battery
While LiNi x Mn y Co 1-x-y O 2 (NMC) is one of the most widely used cathode materials for lithium-ion batteries (LIBs), the composition of NMC is evolving to Ni-rich NMC to achieve higher lithium capacity that fulfills the constant demand for LIBs with ever-higher energy densities. The change in the composition of NMC affects electrochemical features and electrode cross-talk, which explains the performance change during cycling. Here in this study, we introduce various NMC materials (LiNi 0.5 Mn 0.3 Co 0.2 O 2 , LiNi 0.6 Mn 0.2 Co 0.2 O 2 and LiNi 0.8 Mn 0.1 Co 0.1 O 2 ) to reveal how the NMC composition affects electrode cross-talk. The study reveals that NMC composition strongly affects transition metal dissolution; dissolution of manganese linearly decreases as its stoichiometric ratio in NMC decreases, while dissolution of nickel is only prominent in LiNi 0.8 Mn 0.1 Co 0.1 O 2 . Aged electrolyte samples are characterized with high-performance liquid chromatography, and two electrolyte decomposition species, C 8 H 16 O 5 and C 9 H 18 O 5 , are identified across all samples.
25 ENERGY STORAGE↗
Extreme Fast-Charging of Lithium-Ion Cells: Effect on Anode and Electrolyte
In this study, the effects of charge rate in coin cells containing NMC532/1506-Tgraphite are investigated. The cells are cycled at room temperature using charge rates of 1-, 2-, 4-, and 8-C and discharged at the 1-C rate for 50 cycles. The amounts of lithium and LiF are found to be highly correlated with charge time. Three decomposition products are identified in the organic electrolyte. The proposed, empirical formulae for these compounds are C 14 H 33 O 15 P 3 , C 16 H 37 O 15 P 3 , and C 11 H 22 O 7 PF; all are most likely organophosphates formed by the reaction of organic electrolyte decomposition products with LiPF 6 or P(=O)F 3 . The relative concentrations of these organics do not display sensitivity to charge rate. These results imply that a new performance fade mechanism is not introduced by electrolyte decomposition.
25 ENERGY STORAGE↗
Fast Charge-Driven Li Plating on Anode and Structural Degradation of Cathode
Enabling fast charging in lithium ion batteries (LIBs) is a key factor to make electric vehicles drive just like gasoline-powered vehicles when the time comes to refuel. However, fast charging to current LIBs (LiNi x Mn y Co 1–z O 2 /graphite) is limited by lithium plating, which is barely reversible and causes LIBs to lose capacity over time. Thus, research to quantify the lithium plating in LIB cells is extremely important in improving our fundamental understanding of lithium plating behavior and enabling fast charging for LIBs. Here, we precisely quantified the amount of fast-charge-driven lithium plating in a coin-cell composed of LiNi 0.5 Mn 0.3 Co 0.2 O 2 (NMC532)/graphite. We found that the amount of lithium plating gradually increases with the cycle count and reaches 25.59 μmole (26.80 mAh g –1 cathode ) by the 100th cycle. The study also reveals that the NMC532 has lost 19% of its original lithium content after 100 fast-charging cycles; this, correspondingly, causes a lattice volumetric strain of 0.59%.
25 ENERGY STORAGE↗
Transition-Metal Dissolution from NMC-Family Oxides: A Case Study
In this work we investigated the static reactions of highly delithiated Li(Ni 1/3 Mn 1/3 Co 1/3 )O 2 , Li(Ni 0.5 Mn 0.3 Co 0.2 )O 2 , Li(Ni 0.6 Mn 0.2 Co 0.2 )O 2 , and Li(Ni 0.8 Mn 0.1 Co 0.1 )O 2 positive electrodes with 2,3-butanedione and with tetrabutyl ammonium bifluoride as model leaching agents. In the bifluoride trials, it was found that [Ni] in the leachate was proportional to X Co ( X Ni ) 3 , where X M is the ideal stoichiometry in the bulk oxide, and inversely proportional to ( X Mn ) 2 ; [Mn] to X Co ( X Ni ); and [Co] to X Co . The relationships between metal concentrations and stoichiometry may indicate that nickel, as a next-nearest neighbor on the positive electrode surface, can make dissolution more favorable in some instances.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗