Search NASA⌕ Search

Engineering topics

Song, Rongjie

Publications and source records attributed to Song, Rongjie.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Development of a Framework and Methodology for an Advanced Reactor Materials Environmental Effects Design Guide

Advanced non-light-water reactor components may operate at elevated temperature while experiencing cyclic loading, significant neutron irradiation, and exposure to reactor coolant. ASME Boiler and Pressure Vessel Code, Section III, Division 5, provides design rules for elevated-temperature service but does not include specific procedures to account for environmental effects on material properties. This report develops an initial framework and methodology for an Environmental Effects Design Guide (EEDG) focused on neutron irradiation; coolant-environment effects are reserved for future work. The proposed approach treats irradiation as a property-based overlay on the existing Division 5 design process, with two routes: a sparse-data route applying two reduction factors — FCR on creep-rupture strength and FF on fatigue life — for the creep-fatigue evaluations that typically control the design of advanced high-temperature reactor components, and a fuller framework developing the property-to-rule chain across the four Division 5 checks (primary load, strain limits and ratcheting, creep-fatigue, and buckling), together with swelling and weldments as scope items. Both routes are scoped by an in-pile qualification that restricts the use of post-irradiation-examination-derived properties in regimes where an in-pile mechanism could control the design outcome. Illustrative outputs derived on a compiled annealed Type 316 database — FCR ≈ 0.78–0.86 and FF ≈ 0.4 — demonstrate the calculation method within that specific dataset. The framework is an initial, testable design-rule concept; it identifies a practical path for preliminary design evaluations under sparse data and the material data and testing needed to develop the framework further.

Barua, Bipul (ORCID:0000000247184113)↗
DOE OSTI2024

Promoting regulatory acceptance of combined ion and neutron irradiation testing of nuclear reactor materials: Modeling and software considerations

As the needs for the nuclear energy industry continue to evolve in the 21st century, timely adoption of new technological solutions acceptable to regulatory agencies is critical. Quantitative prediction of radiation damage in materials and its impact on mechanical properties is a key component of licensing and regulatory decisions regarding nuclear power plants. Accelerated testing methodologies such as combined ion and neutron irradiation data sets are crucial for the development and deployment of new materials and new manufacturing methods (e.g., additive manufacturing). However, regulatory acceptance of accelerated testing methodologies is necessary for their adoption. Further, the present work discusses the fundamental basis for comparing ion- and neutron-induced material microstructures, the theory behind interpreting radiation damage across length and time scales and radiation types, and the codes, standards, and quality assurance concerns surrounding different modeling methods and software. In particular, recommendations are given as to the path forward that will enable national laboratories, academia, and industry to develop the modeling and software basis for regulatory acceptance of the combined use of ion and neutron irradiation for material performance evaluation.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Role of Nuclear Science User Facilities (NSUF) in Nuclear Energy Materials Research

The Nuclear Science User Facilities (NSUF) is one of a diverse number of U.S. Department of Energy (DOE) user facilities established to provide researchers with the most advanced tools of modern science. The NSUF is unique and represents a consortium of capabilities distributed across the U.S. at twenty-one institutions. The NSUF is centered at and managed from the Idaho National Laboratory (INL), where it was originally founded, but it coordinates activities at twenty “partner” institutions that include universities, the Center for Advanced Energy Studies (CAES), national laboratories, and a nuclear industry vendor. These institutions have capabilities that include neutron, ion, and gamma irradiation, hot cells, advanced materials characterization equipment, and high-performance computing resources. Many of these capabilities were beyond reach for most researchers before NSUF. The NSUF provides researchers to access these capabilities at no cost to nuclear energy researchers to produce the highest quality research results to increase understanding of advanced nuclear energy technologies important to DOE-NE and support national priorities by adapting to the needs of DOE-NE programs, industry, and new innovative concepts for sustainable nuclear future.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2024

Advanced Characterization Capabilities for Nuclear Materials via Nuclear Science User Facilities (NSUF)

Advanced post-irradiation examination (PIE) techniques are required to design new or improved nuclear materials, characterize, and understand in-core behavior of fuel and materials, and support the qualification of new reactor materials. The Nuclear Science User Facilities (NSUF) is the U.S. Department of Energy Office of Nuclear Energy's only designated nuclear science user facility. NSUF provides researchers access to PIE capabilities at Idaho National Laboratory and at a diverse mix of university, national laboratory and industrial partner institutions. The PIE capabilities include novel destructive and non-destructive techniques for radiation damage characterization, such as advanced diffraction techniques (X-ray, electron, or neutron) coupled to extreme environments; in-situ observation of microstructural evolution under irradiation; in-situ irradiation to monitor corrosive attack in coolant environments; in-situ irradiation and mechanical testing; and test methods for synergistic effects of superimposed extreme environments (temperature, irradiation, stress, corrosion) on materials behaviors. This talk will provide an overview of NSUF PIE capabilities.

36 MATERIALS SCIENCE↗
DOE OSTI2024

An approach to combine neutron and ion irradiation data to accelerate material qualification for nuclear reactors

Next-generation nuclear power plants are generally characterized by higher operating temperatures, increased neutron fluences and energies, and distinct corrosive coolant environments versus the existing light water reactor fleet. Whether using existing materials in new environments, newly developed materials tailored for these environments, or new manufacturing methods, the traditional decades-long approach for materials qualification does not facilitate rapid deployment. Ion irradiation has demonstrated success in reproducing material microstructure and select property evolution resulting from neutron irradiation with three to four orders of magnitude reduction in time and cost, making it an ideal candidate for accelerated irradiation testing. Because microstructure has a large impact on bulk material properties, limited neutron irradiation data at lower damage levels can in principle be combined with accelerated ion testing results and modeling and simulation to form an accurate prediction of microstructure evolution and select properties under different neutron irradiation conditions and at higher damage levels. The objective of this work is to present a conceptual framework of specific steps to fulfill several technical challenges associated with qualifying materials for performance in radiation environments on an accelerated time frame. A brief review of the regulatory landscape for materials in nuclear environments is presented, followed by additional overviews to understand the current state of the art for correlation of materials properties across radiation environments using experimental and computational methodologies. Finally, the roles of academia, national laboratories, and industry in the advancement of this accelerated materials qualification framework are discussed as a path forward, with possible case studies presented.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2024

Report on the Integration of Experimental and Modeling Data for Initial Equivalence Study of Microstructural Evolution in Irradiated LPBF 316SS

Advanced materials and manufacturing technologies are poised to improve the safety and design characteristics of nuclear technologies and meet US energy, environmental, and economic needs. In particular, metal additive manufacturing (AM) provides an opportunity to produce novel materials and component geometries, but their use is not without hurdles arising from the inherent microstructure variability that can result from the layer-by-layer build approach. Given the greater possible microstructure variability in AM materials—and the dearth of materials test reactors—it is impractical to rely solely on neutron irradiation studies to produce data for materials qualification for every possibility. This work within the Advanced Materials and Manufacturing Technologies (AMMT) Environmental Effects technical area contributes to the rapid qualification framework by developing a science-driven framework for the accelerated qualification of materials for nuclear environments. A key product of the Environmental Effects technical area of the AMMT program is the Licensing Approach with Ions and Neutrons (LAIN). This approach recognizes that whether using existing materials in new environments, newly developed materials tailored for these environments, or new manufacturing methods, the traditional decades-long approach for materials qualification does not facilitate rapid deployment. In FY 2023, the AMMT program presented a conceptual framework of specific steps to fulfill several technical challenges associated with qualifying materials for performance in radiation environments on an accelerated time frame informed by the state of the art in materials science and a review of the current regulatory landscape. The objective of this section of the Environmental Effects technical area is to critically evaluate and refine the proposed qualification framework presented under AMMT by integrating the research results of the neutron irradiations, the ion irradiations, and modeling efforts. These ongoing efforts span across Argonne National Laboratory (ANL), Idaho National Laboratory (INL), and Oak Ridge National Laboratory (ORNL) and are closely coordinated.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Effect of Heat Treatment on Microstructure and Mechanical Property of 316L Stainless Steel Produced by Laser Powder Bed Fusion

The advanced non-light water reactor designs (Gen IV reactors), including molten salt/ very high temperature/ sodium-cooled and lead-cooled fast reactors, typically operate at higher temperatures and more extreme radiation conditions than light water reactors. An intrinsic part of the deployment and progress of Gen IV reactor designs is selecting the most suitable structural material for a specific application. Additive manufacturing (AM), a fairly new process of making physical, three-dimensional objects from a computer design file, is going to completely change the way of design, build and certify nuclear systems. It offers a range of opportunities to produce complex geometries from existing materials, offers new routes for processing of previously difficult to process materials, allows for design of new high-performance materials, and finally facilitates hybridization of dissimilar materials. This emerging technology has successfully produced cars, wind turbine blade molds and even live cells. It could also open up big opportunities for the nuclear industry to quickly deploy technologies at a fraction of the cost. So far, AM techniques have been preliminarily applied in the field of nuclear reactors, including the classical parts such as the pressure vessel of a small reactor with 508-III steel, the bottom nozzle of a fuel assembly with 304L steel, the fuel cladding with zirconium alloy and the integrated impeller of a pump and the multi-channel valve body with 316L steel [6,7]. The AM applications for operating nuclear reactors started in auxiliary plant components and have slowly migrated to metallic reactors and core components, but many of these are not safety critical components. Although many parts used for nuclear reactors have been fabricated by AM techniques, practical applications in engineering are still a long way off due to the uncertainty factors focused on the processing, material properties, analysis methods and application standards, which feeds the safety and life-cycle of the nuclear reactor. Due to rapid, repeated heating and cooling during production, a high dislocation density was present in the AM material. This microstructure feature is unstable at elevated temperature while high temperature is one of the typical operation environments for nuclear reactors. Thus, it is important to understand the thermal effect on the microstructure of AM material. The objectives of this study are to investigate the effect of heat treatment on the microstructure and mechanical properties of 316L stainless steel produced by laser powder bed fusion additive manufacturing, and to determine an appropriate heat treatment practice that will be applied to the lightweight AM lattice-structured material with the same chemistry. The heat treatment study consisted of annealing the samples at a temperature range of 800 to 1200 oC with a 50 oC increment for different times (1-24 hours), followed by vacuum or air cooling. Microstructural characterization was carried out by Scanning Electron Microscope (SEM). Grain size and crystallographic orientation were investigated by Electron Backscatter Diffraction (EBSD). Vickers hardness tests with a 0.5 kg load were employed to determine the hardness of samples after different heat treatments. After heat treatment, the random crystallographic orientation was preserved, and the volume fraction of high-angle grain boundaries (grain boundary misorientation =15 oC) remained the same. The dislocation density decreased with annealing temperature due to recovery. The fine subgrain structures in the as-printed specimen were quite stable up to 1200 oC. Minimal recrystallization was observed up to 1200 oC. Recrystallization initiated only after 8.5 hours at 1200 oC. The SEM images did not show obvious dependence of microstructure on cooling rate. The hardness of the specimens decreased with increasing annealing temperature as a result of the decrease in dislocation density. It is interesting to note that the AM material showed very similar hardness to the wrought material when annealing at similar temperature, although the microstructures are very different. Annealing at 1050 oC for 1 hour followed by air cooling was selected as the heat treatment procedure for the lattice designed lightweight AM 316L material.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Corrosion testing needs and considerations for additively manufactured materials in nuclear reactors

Additive manufacturing (AM) technologies have developed rapidly in recent years, creating new opportunities and challenges for the nuclear industry; however, adoption requires that their corrosion performance be evaluated. Here, we discuss known reactor-specific corrosion issues for multiple reactor types and engineering concerns such as regulations and standards. A review of corrosion studies conducted on select AM alloys informs a discussion on key bulk and surface factors likely to impact corrosion behaviors. Recommendations to assess corrosion performance for AM materials are provided, including management of the unique nature of as-built AM surfaces and the inherent process variability that occurs for AM components.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Radiation testing of AM materials [Slides]

This presentation discusses the combined irradiation testing methods, strategies, and high-level results of the Advanced Materials and Manufacturing Technologies program. Included are neutron irradiation, ion irradiation, and post-irradiation examination.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Promoting the regulatory acceptance of combined ion and neutron irradiation for material degradation in nuclear reactors

The Advanced Materials and Manufacturing Technologies (AMMT) program within the Department of Energy (DOE) Office of Nuclear Energy has developed its current recommendation for promoting the use of combined ion irradiation and neutron irradiation for the accelerated qualification of materials to be deployed in nuclear reactors. This plan is intended to provide a collaborative path forward that can be adopted by academia, national laboratories, and industry, and has been developed with input from the regulatory research arm of the U.S. Nuclear Regulatory Commission (NRC). To deploy new materials or materials manufactured with new technologies, such as additive manufacturing, materials must be evaluated for reactor-induced degradation from the combination of harsh temperatures, corrosive environments, and radiation fields. However, rapid deployment of materials necessitates accelerated testing methods rather than relying on years of neutron irradiation in a material test reactor. Ion irradiation has demonstrated success in reproducing material microstructure and select property evolution resulting from neutron irradiation with three to four orders of magnitude reduction in time and cost, making it an ideal candidate for accelerated irradiation testing. This presentation provides context governing both the scientific and regulatory aspects of the proposed goal. The discussion is aimed at a broad audience including researchers from industry, national laboratories, and academia. The recommended path forward is presented as a conceptual framework of specific steps. In brief, the strategy entails developing an integrated ion and neutron irradiation test plan for the material property of interest based on the fundamental tenet of the linkage of microstructure and properties in materials. Physics-based modeling interprets ion irradiation data and predicts neutron irradiation microstructure and properties with uncertainty bounds. The first round of testing is sufficient for an initial licensing application using a risk-informed approach, while a minimum required neutron irradiation test plan reduces cost and time requirements. A surveillance program with witness specimens in-reactor provides additional data over time to improve model predictions to higher damage levels and further reduce uncertainty bounds, which can be used for license extensions or longer lifetimes in new license applications.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Lattice Design and Advanced Modeling to Guide the Design of High-Performance Lightweight Structural Materials

Lightweight structural materials are required to increase the mobility of fission batteries. The materials must feature a robust combination of mechanical properties to demonstrate structural resilience. The primary objective of this project is to produce lightweight structural materials whose strength-to-weight ratios exceed those of the current widely used structural materials such as 316L stainless steels (316L SS). To achieve this, advanced modeling and simulation tools were employed to design lattice structures with different lattice parameters and different lattice types. A process was successfully developed for transforming lattice-structures models into Multiphysics Object Oriented Simulation Environment (MOOSE) inputs. Finite element modeling (FEM) was used to simulate the uniaxial tensile testing of the lattice-structured parts to investigate the stress distribution at a given displacement. The preliminary results showed that the lattice-structured sample displayed a lower Young’s modulus in comparison with the solid material and that the unit cell size of the lattice had a minimal effect. The novelty here is to apply up-front modeling to determine the best structure for the application before actually producing the sample. The approach of using modeling as a guiding tool for preliminary material design can significantly save time and cost for material development.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Development of Lightweight Structural Materials with Improved Properties for Fission Batteries

The notion of a “fission battery” conveys a vision focused on realizing very simple “plug-and-play” nuclear systems that can be integrated into a variety of applications requiring affordable, reliable energy in the form of electricity and/or heat and function without operations and maintenance staff. Fission batteries require lightweight structural materials to increase their mobility, and the lightweight materials must demonstrate structural resilience under various conditions. The objective of this work is to develop lattice structured lightweight structural material featuring a good combination of mechanical properties using advanced modeling and simulation together with an advanced additive manufacturing technique such as laser powder bed fusion. The preliminary results show that different lattice structures and types can be successfully meshed using nTopology software, and the lattice structure data can be successfully transformed to Multiphysics Object-Oriented Simulation (MOOSE) Environment input. Finite Element Analysis (FEA) displays that, at macro/engineering scale simulation, the weight saving design has an obvious effect on tensile behavior such as effective elastic modulus and yield stress. The novel approaches of this work are (1) development of lattice structures for improved mechanical properties using advanced simulation and modeling techniques; and (2) model predictions of the mechanical properties (e.g., strength and stress distribution) of macroscopic materials in order to preliminarily select a lattice structure for additive manufacturing.

36 MATERIALS SCIENCE↗
DOE OSTI2024

COMPUTER-AIDED LATTICE DESIGN AND ADVANCED MODELING FOR THE DEVELOPMENT OF LIGHTWEIGHT STRUCTURAL MATERIALS

The notion of a “fission battery” conveys a vision focused on realizing very simple “plug-and-play” nuclear systems that can be integrated into a variety of applications requiring affordable, reliable energy in the form of electricity and/or heat and function without operations and maintenance staff. Fission batteries require lightweight structural materials to increase their mobility, and the lightweight materials must demonstrate structural resilience under various conditions. The objective of this work is to develop lattice structured lightweight structural material featuring a good combination of mechanical properties using advanced modeling and simulation together with an advanced additive manufacturing technique such as laser powder bed fusion. The preliminary results show that different lattice structures and types can be successfully meshed using nTopology software, and the lattice structure data can be successfully transformed to Multiphysics Object-Oriented Simulation (MOOSE) Environment input. Finite Element Analysis (FEA) displays that, at macro/engineering scale simulation, the weight saving design has an obvious effect on tensile behavior such as effective elastic modulus and yield stress. The novel approaches of this work are (1) development of lattice structures for improved mechanical properties using advanced simulation and modeling techniques; and (2) model predictions of the mechanical properties (e.g., strength and stress distribution) of macroscopic materials in order to preliminarily select a lattice structure for additive manufacturing.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Development of Lightweight Structural Materials with Improved Properties for Fission Batteries

The notion of a “fission battery” conveys a vision focused on realizing very simple “plug-and-play” nuclear systems that can be integrated into a variety of applications requiring affordable, reliable energy in the form of electricity and/or heat and function without operations and maintenance staff. Fission batteries require lightweight structural materials to increase their mobility, and the lightweight materials must demonstrate structural resilience under various conditions. The objective of this work is to develop lightweight structural material featuring a good combination of mechanical properties using advanced modeling and simulation together with an advanced additive manufacturing technique such as laser powder bed fusion. The preliminary results show that different lattice structures and types can be successfully meshed using nTopology software, and the lattice structure data can be successfully transformed to Multiphysics Object-Oriented Simulation Environment (MOOSE) input. Finite Element Analysis (FEA) displays that, at macro/engineering scale simulation, the weight saving design has an obvious effect on tensile behavior such as effective elastic modulus and yield stress. The novel approaches of this work are (1) development of optimized lattice structures for improved mechanical properties using advanced simulation and modeling techniques; and (2) model predictions of the mechanical properties (e.g., strength and stress distribution) of macroscopic materials in order to preliminarily select a lattice structure for additive manufacturing.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Promoting the Regulatory Acceptance of Combined Ion and Neutron Irradiation for Material Degradation in Nuclear Reactors

The Advanced Materials and Manufacturing Technologies (AMMT) program within the Department of Energy Office of Nuclear Energy has developed its current recommendation for promoting the use of combined ion and neutron irradiation data for the accelerated qualification of nuclear reactor materials. This plan is intended to provide a collaborative path forward that can be adopted by academia, national laboratories, and industry, and has been developed with input from the regulatory research arm of the U.S. Nuclear Regulatory Commission (NRC). In the context of nuclear energy, the U.S. Department of Energy is responsible for nuclear energy-related research and development and promotion of nuclear technologies, while the NRC is an independent regulatory agency responsible for the safety of the civilian use of nuclear technologies. These two agencies thus have distinct but interconnected roles regarding the development and deployment of nuclear technologies. As the needs for the nuclear energy industry continue to evolve in the 21st century, it is critical to set the pace for timely industry adoption of new technological solutions that also can be accepted by regulatory agencies. New ways of collecting and utilizing data for regulatory purposes have become a necessity.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Corrosion Testing Needs and Considerations for Additively Manufactured Materials in Nuclear Reactors

The Advanced Materials and Manufacturing Technologies (AMMT) program within the Department of Energy, Office of Nuclear Energy (DOE-NE) has developed its current recommendation for its corrosion testing strategy to deploy additively manufactured (AM) materials in advanced nuclear reactors. Additive manufacturing technologies have developed rapidly in recent years, creating new opportunities and challenges for the nuclear industry. To adopt AM technologies, the corrosion performance of AM materials needs to be adequately evaluated.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗