Search NASA⌕ Search

Engineering topics

Soni, Vishal

Publications and source records attributed to Soni, Vishal.

7 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

High Density of Strong yet Deformable Intermetallic Nanorods Leads to an Excellent Room Temperature Strength-Ductility Combination in a High Entropy Alloy

This paper introduces a new microstructural template for high entropy alloys (HEAs), where the face centered cubic (FCC) complex concentrated solid solution is reinforced with a high density of strong, yet deformable, nanorods of an ordered multi-component intermetallic L12 compound. Thermodynamic modeling has been employed to design this HEA with a large L12 volume fraction. Thermo-mechanical processing by isothermal annealing of the conventionally processed bulk cold-rolled alloy directly at precipitation temperatures, has been applied to produce a high density of uniformly distributed L12 nanorods within refined FCC grains, resulting from concomitant recrystallization and discontinuous precipitation processes. The nanorod morphology of the discontinuous L12 product has been established from three-dimensional atom probe tomography. The refined grains result in a complete coverage of the microstructure with discontinuously precipitated intermetallic nanorods. This nanorod strengthened HEA exhibits an exceptionally high room temperature yield strength of ~1630 MPa, good tensile ductility of ~15%, and an ultimate tensile strength of ~1720 MPa. Furthermore, a single L12 phase alloy, melted based on the precipitate composition in the two-phase FCC + L12 HEA, exhibits very high compressive deformability and strain hardenability, unusual for ordered intermetallic compounds. These results open a new strategy for design of fine-grained microstructures strengthened via ordered intermetallic phases, exploiting the beneficial effects of discontinuous precipitation, for achieving very high room temperature tensile strengths while maintaining good ductility.

Gwalani, Bharat↗
DOE OSTI2020

Engineering Multi-scale B2 Precipitation in a Heterogeneous FCC Based Microstructure to Enhance the Mechanical Properties of a Al0.5Co1.5CrFeNi1.5 High Entropy Alloy

While ordered L12 or gamma prime precipitates in face centered cubic (FCC) based microstructures have been extensively used for strengthening Nickel or Cobalt base superalloys, and more recently in high entropy alloys (HEAs) or complex concentrated alloys (CCAs), the possibility of exploiting ordered B2 precipitates in FCC-based systems has been relatively less investigated. The present study shows the propensity of developing a heterogeneous microstructure, consisting of two different distributions of FCC grain sizes, and two different size scales of B2 precipitates, within an FCC-based Al0.5Co1.5CrFeNi1.5 HEA/CCA. This alloy composition has been designed using solution thermodynamics-based modeling such that it has a high phase fraction and solvus temperature of the B2 phase. The resulting heterogenous microstructure exhibited an approximately 400% increase in yield strength with respect to the single-phase FCC solid solution condition of the same alloy while maintaining very good tensile ductility ~20 %.

Dasari, Sriswaroop↗
DOE OSTI2020

Engineering transformation pathways in an Al 0.3 CoFeNi complex concentrated alloy leads to excellent strength–ductility combination

Guided by thermodynamic modeling, engineering phase transformation pathways via thermo-mechanical processing, in a complex concentrated alloy/high entropy alloy (HEA) of composition Al 0.3 CoFeNi, lead to a novel multi-scale microstructure consisting of fine-scale FCC + L1 2 grains mixed with B2 + BCC grains. The two-step pathway comprises initial decomposition of the parent single-phase FCC to form a fine-grained FCC + B2 microstructure, which further decomposes in the second step into the complex four-phase mixture, exhibiting an excellent combination of tensile yield stress of ~1490 MPa, ultimate tensile strength of ~1663 MPa, with a good ductility of ~12% at room temperature. This paper reports a novel multi-phase microstructure in a HEA/CCA similar to the microstructure observed in dual-phase stainless steel. This report exemplifies the novelty of HEA/CCA compositional space.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Influence of non-magnetic Cu on enhancing the low temperature magnetic properties and Curie temperature of FeCoNiCrCu(x) high entropy alloys

The microstructure and magnetic properties of three face-centered cubic (FCC) FeCoNiCrCu(x) high entropy alloys (HEAs) (x=0, 0.5, 1) are investigated. Interestingly, addition of the nonmagnetic element Cu to FeCoNiCr HEA is found to enhance exchange interactions and low temperature saturation magnetization. The paramagnetic to ferromagnetic Curie transition temperature increases from 85 K for FeCoNiCr to 118 K for FeCoNiCrCu. This is counterintuitive since Cu is nonmagnetic; however, atom probe tomography revealed Cu rich clusters containing 5 at% Ni and 1 at% each of Fe, Co, Cr, within FCC matrix, these clusters altered the matrix composition and consequently its magnetic properties.

Chaudhary, Varun↗
DOE OSTI2020

Hierarchical Eutectoid Nano-lamellar Decomposition in an Al 0.3 CoFeNi Complex Concentrated Alloy

This paper reports a novel eutectoid nano-lamellar (FCC + L1 2 )/(BCC + B2) microstructure that has been discovered in a relatively simple Al 0.3 CoFeNi high entropy alloy (HEA) or complex concentrated alloy (CCA). This novel eutectoid nano-lamellar microstructure presumably results from the complex interplay between Al-mediated lattice distortion (due to its larger atomic radius) in a face-centered cubic (FCC) CoFeNi solid solution, and a chemical ordering tendency leading to precipitation of ordered phases such as L1 2 and B2. This eutectoid microstructure is a result of solid-state decomposition of the FCC matrix and therefore distinct from the commonly reported eutectic microstructure in HEAs which results from solidification. This novel nano-lamellar microstructure exhibits a tensile yield strength of 1074 MPa with a reasonable ductility of 8%. The same alloy can be tuned to form a more damage-tolerant FCC + B2 microstructure, retaining high tensile yield stress (~900 MPa) with appreciable tensile ductility (>20%), via annealing at 700 °C. Such tunability of microstructures with dramatically different mechanical properties can be effectively engineered in the same CCA, by exploiting the complex interplay between ordering tendencies and lattice distortion.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Phase Inversion in a Two-phase, BCC+B2, Refractory High Entropy Alloy

A phenomenon of "phase inversion", presumably the first ever experimental evidence in metallic alloys, is shown in a refractory high entropy alloy (RHEA), Al0.5NbTa0.8Ti1.5V0.2Zr. Phase inversion in crystalline solid systems is driven by the differences in elastic modulus of the two phases. Quenching from a high-temperature single phase field, the RHEA exhibits a co-continuous mixture of a disordered BCC and an ordered B2 phase, that upon isothermal annealing at 600°C develops via spinodal decomposition into a continuous B2 matrix with discrete cuboidal BCC precipitates aligned along the <001> directions. Longer term annealing at 600°C results in the development of necking constrictions along the B2 channels, eventually pinching-off these channels and making the BCC phase continuous with discrete B2 precipitates. This inversion the process can be related to the simultaneous operation of two processes:(i) spheroidization of the initially discrete cuboidal BCC precipitates driven by a reduction in the total interface energy and (ii) an increase in the stiffness of the B2 phase, relative to the BCC phase, due to chemical composition changes during annealing, forcing the B2 regions to become discrete driven by the reduction in the total elastic strain energy.

Soni, Vishal↗