Search NASA⌕ Search

Engineering topics

Spiegel, Y

Publications and source records attributed to Spiegel, Y.

Simulation of BF{sub 3} plasma immersion ion implantation into silicon

Plasma immersion ion implantation from a BF{sub 3} plasma into crystalline (100) silicon was performed using the PULSION plasma doping tool. Implanted boron profiles were measured with the SIMS method and simulated using models with different levels of sophistication. The physical implantation model is based on an analytical energy distribution for ions from the plasma and uses a Monte-Carlo simulation code. An analytical model of plasma immersion ion implantation that assumes a uniform and isotropic implantation was implemented in a software module called IMP3D. The functionality of this module which was initially envisaged for the three-dimensional simulation of conventional ion implantation was extended to plasma immersion ion implantation and examples of 2D and 3D simulations from this are presented.

36 MATERIALS SCIENCE↗

BF{sub 3} PIII modeling: Implantation, amorphisation and diffusion

In the race for highly doped ultra-shallow junctions (USJs) in complementary metal oxide semi-conductor (CMOS) technologies, plasma immersion ion implantation (PIII) is a promising alternative to traditional beamline implantation. Currently, no commercial technology computer aided design (TCAD) process simulator allows modeling the complete USJ fabrication process by PIII, including as-implanted dopant profiles, damage formation, dopant diffusion and activation. In this work, a full simulation of a p-type BF{sub 3} PIII USJ has been carried out. In order to investigate the various physical phenomena mentioned above, process conditions included a high energy/high dose case (10 kV, 5 Multiplication-Sign 10{sup 15} cm{sup -2}), specifically designed to increase damage formation, as well as more technology relevant implant conditions (0.5 kV) for comparison. All implanted samples were annealed at different temperatures and times. As implanted profiles for both boron and fluorine in BF{sub 3} implants were modeled and compared to Secondary Ion Mass Spectrometry (SIMS) measurements. Amorphous/crystalline (a/c) interface depths were measured by transmission electron microscopy (TEM) and successfully simulated. Diffused profiles simulations agreed with SIMS data at low thermal budgets. A boron peak behind the a/c interface was observed in all annealed SIMS profiles for the 10 kV case, indicating boron trapping from EOR defects in this region even after high thermal budgets. TEM measurements on the annealed samples showed an end of range (EOR) defects survival behind the a/c interface, including large dislocation loops (DLs) lying on (001) plane parallel to the surface. In the last part of this work, activation simulations were compared to Hall measurements and confirmed the need to develop a (001) large BICs model.

36 MATERIALS SCIENCE↗

Physical and Electrical Characterization of 120 nm Technology Node Devices using PULSION registered Plasma Doping

Plasma doping is a well-known technology used in semiconductor manufacturing for two major DRAM manufacturing steps: polysilicon counter-doping and contact doping. For these specific applications, the PULSION tool shows physical benefits, as well as cost of ownership benefits, with the capability to perform low energy, high dose implantation in a high throughput mode. Nevertheless, throughput is a common challenge for all semiconductor manufacturing, not only for advanced technologies. The purpose of this study is to demonstrate that plasma doping is not limited to advanced devices, but can also satisfy the requirements of >90 nm nodes, for specific applications such as Lightly Doped Drain (LDD) implants.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Different Profile Responses to Dose Variation for B{sub 2}H{sub 6} and BF{sub 3} Plasma Doping using PULSION registered

Plasma doping has been accepted into semiconductor manufacturing for two low energy, high dose implant applications. The p-type polysilicon counter-doping and contact doping for DRAM devices can be carried out using BF{sub 3} or B{sub 2}H{sub 6} precursor gas. The choice between these two precursors depends on the benefits and constraints of each one. In order to identify these benefits and constraints, the boron dopant profile responses to dose variation for both precursors have been studied using the PULSION plasma doping tool.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

PULSION registered HP: Tunable, High Productivity Plasma Doping

Plasma doping has been explored for many implant applications for over two decades and is now being used in semiconductor manufacturing for two applications: DRAM polysilicon counter-doping and contact doping. The PULSION HP is a new plasma doping tool developed by Ion Beam Services for high-volume production that enables customer control of the dominant mechanism--deposition, implant, or etch. The key features of this tool are a proprietary, remote RF plasma source that enables a high density plasma with low chamber pressure, resulting in a wide process space, and special chamber and wafer electrode designs that optimize doping uniformity.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗