Engineering topics

Spinhirne, James D.

Publications and source records attributed to Spinhirne, James D..

At least 73 records · Page 4

NASA NTRS1995

New generation lidar systems for eye safe full time observations

The traditional lidar over the last thirty years has typically been a big pulse low repetition rate system. Pulse energies are in the 0.1 to 1.0 J range and repetition rates from 0.1 to 10 Hz. While such systems have proven to be good research tools, they have a number of limitations that prevent them from moving beyond lidar research to operational, application oriented instruments. These problems include a lack of eye safety, very low efficiency, poor reliability, lack of ruggedness and high development and operating costs. Recent advances in solid state laser, detectors and data systems have enabled the development of a new generation of lidar technology that meets the need for routine, application oriented instruments. In this paper the new approaches to operational lidar systems will be discussed. Micro pulse lidar (MPL) systems are currently in use, and their technology is highlighted. The basis and current development of continuous wave (CW) lidar and potential of other technical approaches is presented.

Spinhirne, James D.↗

NASA NTRS1993

Comparison of radiation and cloud parameters derived from satellite and aircraft measurements during FIRE 2 cirrus IFO

Meteorological satellite instrument pixel sizes are often much greater than the individual cloud elements in a given scene. Partially cloud-filled pixels can be misinterpreted in many analysis schemes because the techniques usually assume that all of the cloudy pixels are cloud filled. Coincident Landsat and Geostationary Operational Environmental Satellite (GOES) data and degraded-resolution Landsat data were used to study the effects of both sensor resolution and analysis techniques on satellite-derived cloud parameters. While extremely valuable for advancing the understanding of these effects, these previous studies were relatively limited in the number of cloud conditions that were observed and by the limited viewing and illumination conditions. During the First ISCCP Regional Experiment (FIRE) Phase 2 (13 Nov. - 7 Dec. 1991), the NASA ER-2 made several flights over a wide range of cloud fields and backgrounds with several high resolution sensors useful for a variety of purposes including serving as ground truth for satellite-based cloud retrievals. This paper takes a first look at utilizing the ER-2 for validating cloud parameters derived from GOES and NOAA-11 Advanced Very High Resolution Radiometer (AVHRR) data.

Heck, Patrick W.↗

NASA NTRS1993

The 5-6 December 1991 FIRE IFO 2 jet stream cirrus case study: The influence of volcanic aerosols

In presenting an overview of the cirrus clouds comprehensively studied by ground-based and airborne sensors from Coffeyville, KS, during the 5-6 Dec. 1992 Project FIRE (First International Satellite Cloud Climatology Project Regional Experiment) IFO II case study period, evidence is provided that volcanic aerosols from the June 1991 Pinatubo eruptions significantly influenced the formation and maintenance of the cirrus. Following the local appearance of a spur of stratospheric volcanic debris from the subtropics, a series of jet streaks subsequently conditioned the troposphere through tropopause foldings with sulfur-based particles that became effective cirrus cloud-forming nuclei. Aerosol and ozone measurements suggest a complicated history of stratospheric-tropospheric exchanges embedded within the upper level flow, and cirrus cloud formation was noted to occur locally at the boundaries of stratospheric aerosol-enriched layers that became humidified through diffusion, precipitation, or advective processes. Apparent cirrus cloud alterations include abnormally high ice crystal concentrations (up to approximately 600 l(sup -1), small but complex radial ice crystal types, and relatively large haze particles in cirrus uncinus cell heads at temperatures between -40 to -50 C. Implications for volcanic-cirrus cloud climate effects, and usual (non-volcanic aerosol) jet stream cirrus cloud formation are discussed.

Sassen, Kenneth↗

NASA NTRS1993

Micro pulse laser radar

An eye safe, compact, solid state lidar for profiling atmospheric cloud and aerosol scattering is disclosed. The transmitter of the micro pulse lidar is a diode pumped micro-J pulse energy, high repetition rate Nd:YLF laser. Eye safety is obtained through beam expansion. The receiver employs a photon counting solid state Geiger mode avalanche photodiode detector. Data acquisition is by a single card multichannel scaler. Daytime background induced quantum noise is controlled by a narrow receiver field-of-view and a narrow bandwidth temperature controlled interference filter. Dynamic range of the signal is limited to optical geometric signal compression. Signal simulations and initial atmospheric measurements indicate that micropulse lider systems are capable of detecting and profiling all significant cloud and aerosol scattering through the troposphere and into the stratosphere. The intended applications are scientific studies and environmental monitoring which require full time, unattended measurements of the cloud and aerosol height structure.

Spinhirne, James D.↗

NASA NTRS1993

Micro pulse lidar

An eye safe, compact, solid state lidar for profiling atmospheric cloud and aerosol scattering has been demonstrated. The transmitter of the micropulse lidar is a diode pumped micro-J pulse energy, high repetition rate Nd:YLF laser. Eye safety is obtained through beam expansion. The receiver employs a photon counting solid state Geiger mode avalanche photodiode detector. Data acquisition is by a single card multichannel scaler. Daytime background induced quantum noise is controlled by a narrow receiver field-of-view and a narrow bandwidth temperature controlled interference filter. Dynamic range of the signal is limited by optical geometric signal compression. Signal simulations and initial atmospheric measurements indicate that systems built on the micropulse lidar concept are capable of detecting and profiling all significant cloud and aerosol scattering through the troposphere and into the stratosphere. The intended applications are scientific studies and environmental monitoring which require full time, unattended measurements of the cloud and aerosol height structure.

Spinhirne, James D.↗

NASA NTRS1992

The Global Backscatter Experiment Airborne Pulsed Lidar Measurements

The Global Backscatter Experiment (GLOBE) was intended to provide data on prevailing values of atmospheric backscatter cross section. The primary intent was predicting the performance of space-borne lidar systems. A second and related goal was to understand the source and characteristics of atmospheric aerosol particles. In this paper the authors give a summary of measurement results with emphasis on the magnitude, structure, characteristics and variability of the observed atmospheric aerosol and cloud scattering. The GLOBE pulsed lidar measurements provide an extensive data set on the magnitude and variability of aerosol and cloud backscatter of the atmosphere. The data defines atmospheric aerosol scattering characteristics and should prove to be an important resource for determination of the performance and design of laser remote sensing instruments.

Spinhirne, James D.↗

NASA NTRS1992

Multi-wavelength Airborne Lidar Intercomparisons of Aerosol and Cirrus Backscatter over the Pacific Ocean

Airborne CO2 and Nd:YAG lidar instruments were flown on the NASA DC-8 research aircraft during two extended missions over the Pacific. The objectives during these flights were to characterize aerosol backscatter levels at infrared wavelengths in relatively pristine regions of the troposphere, and to observe cloud effects on lidar signals. In addition, the three wavelength Nd:YAG data were processed using independent temperature profile information, in order to deduce the Rayleigh scattering component of the total backscatter at each wavelength. The data can be used to better understand the capabilities of various airborne or Earth-orbiting lidar designs to provide backscatter information from aerosols and clouds, or to provide Doppler or DIAL information from aerosol and cloud backscatter.

Menzies, Robert T.↗

NASA NTRS1992

Intercomparisons of Lidar Backscatter Measurements and In-situ Data from GLOBE

The Global Backscatter Experiment (GLOBE) took place during Nov. 1989 and May - Jun. 1990 and involved flight surveys of the Pacific region by the NASA DC-8 aircraft. The experimental instruments were lidars operating at wavelengths ranging from the visible to the thermal infrared and various optical particle counters for in-situ measurements. The primary motivation for GLOBE was the development of spaceborne wind sensing lidar. This paper will concern a comparison of direct backscatter measurements and backscatter calculated from particle counter data. Of special interest is that the particle measurements provided data on composition, and thus refractive index variation may be included in the analysis.

Chudamani, S.↗

NASA NTRS1992

Cirrus microphysics and radiative transfer - Cloud field study on 28 October 1986

An analysis of remote-sensing measurements which had detected an inhomogeneous cloud structure, at 6-11 km altitude, in the data acquired during the FIRE 86 experiment in a 75 x 50 km cirrus cloud field, has derived fluxes whose comparison with modeled fluxes imply a modeling-based underestimation of both solar reflectivity/attenuation and downward IR fluxes. Reconciliation of model results with measurements can be achieved either by adding large concentrations of ice crystals or by altering the backscattering properties of ice crystals.

Kinne, Stefan↗

NASA NTRS1992

An airborne system for collecting polarization imagery

This paper describes a recently completed electrooptical camera flying onboard the NASA ER-2 high altitude aircraft. The device includes a six-position filter wheel which can be fitted with a combination of polarizing and/or spectral filters. An alternate configuration will include a polarizing filter which can be rotated to any angle under computer control. The camera mount in the nose of the ER-2 can tilt forward or aft up to 40 degrees, both for bidirectional reflectance studies and for image motion compensation (the aircraft moves 34 meters between frame acquisitions). The ground resolution is nominally 5 meters from and altitude of 20 km. Spectral responsivity is that of the silicon imaging array (Kodak KAF-1400). Initial data sets were acquired in support of the International Satellite Cloud Climatology Program Regional Experiment of November, 1991, and will be used to study cirrus cloud properties.

Hildum, Edward A.↗

NASA NTRS1991

Determination of the optical thickness and effective particle radius of clouds from reflected solar radiation measurements. II - Marine stratocumulus observations

A multispectral scanning radiometer has been used to obtain measurements of the reflection function of marine stratocumulus clouds at 0.75 micron and at 1.65 and 2.16 microns. These observations were obtained from the NASA ER-2 aircraft as part of the FIRE, conducted off the coast of southern California during July 1987. Multispectral images of the reflection function were used to derive the optical thickness and the effective particle radius of stratiform cloud layers on four days. In addition to the radiation measurements, in situ microphysical measurements were obtained from an aircraft. In this paper, the remote sensing results are compared with in situ observations, which show a good spatial correlation for both optical thickness and effective radius. These comparisons further show systematic differences between remote sensing and in situ values, with a tendency for remote sensing to overestimate the effective radius by about 2-3 microns, independent of particle radius. The optical thickness, in contrast, is somewhat overestimated for small optical thicknesses and underestimated for large optical thicknesses. An introduction of enhanced gaseous absorption at a wavelength of 2.16 microns successfully explains some of these observed discrepancies.

Nakajima, Teruyuki↗

NASA NTRS1991

Aircraft overflight measurements of midwest severe storms - Implications on geosynchronous satellite interpretations

The instrumented NASA ER-2 aircraft overflew severe convection with IR V features for the first time in the midwest United States during May 1984. Measurements taken by the ER-2 were: visible and IR imagery, high-frequency passive microwave (92, 183 GHz) imagery, nadir lidar backscattered return, and flight altitude information. The May 7 and May 13, 1984 cases are analyzed in detail and the various data sources are combined and compared with GOES imagery. The high resolution aircraft IR imagery shows that thermal couplets are considerably more pronounced than in GOES imagery. In one of the cases (May 7, 1984) the minimum cloud-top IR temperature was located upshear of the overshooting cloud top in the lidar height field. The IR temperatures in the downshear anvils were as much as 5 C warmer than the ambient air temperatures, implying that the upwelling IR radiance comes from about 0.5-1.0 km below the cloud top. The in situ ER-2 measurements of temperature and air velocity 3-4 km above the overshooting tops showed very intense temperature and vertical velocity, perturbations. These perturbations are suggestive of lee waves generated by the overshooting tops or a cold dome above the squall line possibly due to tropopause lifting by the storms.

Heymsfield, Gerald M.↗

NASA NTRS1991

Visible and near infrared observation on the Global Aerosol Backscatter Experiment (GLOBE)

The Global Aerosol Backscatter Experiment (GLOBE) was intended to provide data on prevailing values of atmospheric backscatter cross-section. The primary intent was predicting the performance of spaceborne lidar systems, most notably the Laser Atmospheric Wind Sounder (LAWS) for the Earth Observing System (EOS). The second and related goal was to understand the source and characteristics of atmospheric aerosol particles. From the GLOBE flights, extensive data was obtained on the structure of clouds and the marine planetary boundary layer. A notable result for all observations is the consistency of the large increases in the aerosol scattering ratio for the marine boundary layer. Other results are noted.

Spinhirne, James D.↗

NASA NTRS1991

Lidar aerosol and cloud backscatter at 0.53, 1.06 and 1.54 microns

The performance space borne or airborne lidar remote sensor is critically dependent on the magnitude the atmospheric backscatter cross section for aerosol and clouds. Measurements are required to establish a representative global distribution. There has been in particular a lack of observations in the Southern Hemisphere and for remote ocean areas. The Global Backscatter Experiment (GLOBE) was flown on the NASA DC-8 aircraft in November, 1989 and May, 1990 throughout northern and southern Pacific regions. A lidar system to measure aerosol backscatter cross section at the visible and near IR wavelengths of 1.06, 1.54 and 0.53 microns was included in the missions. From the global flight surveys, extensive data have been obtained on aerosol and cloud backscatter cross section and structure throughout the troposphere. These data define the feasibility of proposed lidar applications.

Spinhirne, James D.↗

NASA NTRS1991

Visible and near IR lidar backscatter observations on the GLOBE Pacific Survey missions

Measurement techniques and initial results of the Global Backscatter Experiment (GLOBE) performed in November 1989 and May-June 1990 to provide data on prevailing values of atmospheric backscatter cross section are presented. The upper troposphere aerosol scattering cross section was low in the Southern Hemisphere for the May-June flights and low in the Northern Hemisphere for the November flights. The initial results indicate that the instrumentation and calibration techniques applied for the near IR lidar measurements were successful.

Spinhirne, James D.↗

NASA NTRS1991

NASA's program in lidar remote sensing

Several major NASA research efforts in lidar remote sensing are reviewed, with attention given to hardware and key sensor issues along with results and expectations. The discussion covers temperature and pressure measurements, measurements methods and instrumentation, pressure data, wind field measurements, atmospheric backscatter measurement, aerosol and cloud measurements, and water vapor measurement. Consideration is also given to the applicability of lidar measurements to problems of operational weather analysis and forecasting, climate studies, mesoscale and severe storm analysis and forecastig, and studies of atmosphere/surface interface.

Theon, John S.↗

NASA NTRS1990

The 27-28 October 1986 FIRE IFO cirrus case study - A five lidar overview of cloud structure and evolution

During the case study from the First ISCCP (International Satellite Cloud Climatology Program) Regional Experiment (FIRE) Intensive Field Observation (IFO), one airborne lidar system and four ground-based systems collected linear depolarization, intrinsically calibrated backscatter, and Doppler velocity information. Data presented describe the temporal evolution and spatial distribution of cirrus clouds over an area encompassing southern and central Wisconsin. Cirrus cloud types include dissipating subvisual and thin fibrous cirrus cloud bands, an isolated mesoscale uncinus complex, a large-scale, deep cloud that developed into an organized cirrus structure within the lidar array, and a series of intensifying mesoscale cirrus cloud masses. It is noted that the cirrus frequently developed in the vertical from particle fallstreaks emanating from generating regions at or near cloud tops; however, glaciating supercooled altocumulus clouds contributed to the production of ice mass at the base of the deep cirrus cloud.

Sassen, Kenneth↗

NASA NTRS1990

The 27-28 October 1986 FIRE IFO cirrus case study - Cloud microstructure

Using aircraft in-situ measurements, the microphysics of cirrus clouds observed on 28 Oct. 1986 during FIRE were examined. Results are presented as one component of a coordinated study of the cirrus on the day. The study contributes to the understanding of cold clouds by: (1) providing microphysical data to supplement satellite and aircraft data for investigating cirrus cloud radiative effects; (2) providing more complete information on ice particle evolution and cloud forcing mechanisms than has been available through the use of instrumentation with higher resolution and more accurate calibration; (3) expanding the knowledge of the particle characteristics in cold liquid water clouds, through improved instrumentation and by making use of sensors on other platforms, such as lidar; and (4) by estimating the ice nucleus concentrations active at low temperatures in the upper troposphere from the concentrations of ice particles in colloidally stable liquid water clouds.

Heymsfield, Andrew J.↗