Search NASA⌕ Search

Engineering topics

Sridar, Soumya

Publications and source records attributed to Sridar, Soumya.

13 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Rapid data acquisition and machine learning-assisted composition design of functionally graded alloys via wire arc additive manufacturing

Abstract The lack of high-quality datasets in materials science hinders artificial intelligence (AI)-driven alloy design. To address this challenge, wire arc additive manufacturing (WAAM) was employed to fabricate graded alloys, generating extensive data for machine learning (ML)-assisted property prediction. ML models were developed using high-throughput experiments, computational models, and genetic algorithm to optimize feature selection, successfully predicting hardness and porosity. The ML model demonstrated its efficacy by designing a gradient alloy with enhanced properties. However, scaling up revealed uncertainties in tensile property and porosity due to differences in size and thermal conditions between the designed alloy build and the gradient print used to construct the ML model. This underscores the need for uncertainty quantification and process optimization in WAAM-driven alloy design. Our work advances AI-integrated additive manufacturing, offering a rapid approach to exploring process–structure–property relationships and accelerating materials development.

Wang, Xin↗
DOE OSTI2024

Aging heat treatment design for Haynes 282 made by wire-feed additive manufacturing using high-throughput experiments and interpretable machine learning

Wire-feed additive manufacturing (WFAM) produces superalloys with complex thermal cycles and unique microstructures, often requiring optimized heat treatments. To address this challenge, we present a hybrid approach that combines high-throughput experiments, precipitation simulation, and machine learning to design effective aging conditions for the WFAM Haynes 282 superalloy. Our results demonstrate that the γ’ radius is the critical microstructural feature for strengthening Haynes 282 during post-heat treatment compared with the matrix composition and γ’ volume fraction. New aging conditions at 770°C for 50 hours and 730°C for 200 hours were discovered based on the machine learning model and were applied to enhance yield strength, bringing it on par with the wrought counterpart. This approach has significant implications for future AM alloy production, enabling more efficient and effective heat treatment design to achieve desired properties.

CALPHAD↗
DOE OSTI2023

Achieving High Strength and Creep Resistance in Inconel 740H Superalloy through Wire-Arc Additive Manufacturing and Thermodynamic-Guided Heat Treatment

Inconel 740H superalloy is commonly used in advanced ultra-supercritical power plants since it possesses excellent strength and creep resistance. This study investigates the microstructure and mechanical properties of Inconel 740H superalloy fabricated using wire-arc additive manufacturing. The as-printed microstructure consisted of columnar γ grains with the Laves phase and (Nb, Ti)C carbides as secondary phases. The anisotropy in grain structure increased from the bottom to the top regions, while the hardness was highest in the middle portion of the build. To guide the post-heat treatment design, thermodynamic and kinetic simulations were employed to predict the temperature and time. Complete recrystallization with the Laves phase dissolution occurred throughout the build after homogenization at 1200 °C for 2 h. The peak hardness was achieved after aging at 760 °C for 12 h with the M 23 C 6 carbides decorating the grain boundaries and γ’ precipitates in the grain interior. The yield strength (655 MPa) and ductility (29.5%) in the post-heat treated condition exceeded the design targets (620 MPa, 20%). Stress rupture tests at 750 °C showed that the high-temperature performance was at par with the wrought counterparts. The fracture mode after rupture was identified to be intergranular with the presence of grain boundary cavities along with grain boundary sliding.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Thermodynamic modeling of KCl-PrCl 3 and KCl-LiCl-PrCl 3 systems

Molten salt electrolysis can recover the actinides from spent nuclear fuels, and it involves a eutectic LiCl-KCl in molten form as an electrolyte. During reprocessing, the concentration of fission products such as La, Nd, Pr, etc., increases and affects the recovery efficiency of the electrolyte. In this work, thermodynamic modeling of KCl-PrCl 3 and KCl-LiCl-PrCl 3 systems was carried out using the CALPHAD (Calculation of Phase Diagrams) approach for the first time. The thermodynamic functions for the pure salts were taken from the SGTE (Scientific Group Thermodata Europe) Substances (SSUB) database. The experimental thermochemical and phase equilibria data available in the literature were used as input for the assessment of KCl-PrCl 3 and KCl-LiCl-PrCl 3 systems. The model parameters for the KCl-LiCl system were adjusted to include the new Gibbs energy descriptions for the pure salts. In addition, the sublattice model for the liquid phase in the LiCl-PrCl 3 system was modified and reassessed to ensure the model compatibility for higher-order extrapolation. There is a good agreement between the experimental and calculated thermochemical and phase diagram data for all the optimized constituent binaries and the ternary system. Furthermore, this work will be beneficial for determining the solubility limit of PrCl 3 in molten LiCl-KCl electrolytes and their thermodynamic properties for improving the efficiency of the pyrochemical process.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Thermodynamic description of molten salt systems: KCl-LiCl-NaCl and KCl-LiCl-NdCl 3

The mixture of KCl and LiCl has been used as electrolyte in the electrorefining process to recover uranium from used nuclear fuels due to the low melting point. However, lanthanides and sodium in the reactor waste continuously dissolve into it and thus alter its thermodynamic properties. To understand the thermodynamic behavior evolution of the electrolyte with the accumulation of impurities, thermodynamic modeling for KCl-LiCl-NaCl and KCl-LiCl-NdCl 3 and four constituent binary systems in the entire composition space was performed using the CALPHAD (CALculation of PHAse Diagrams) approach. The ionic liquid was described by the two-sublattice model, where neutral species were introduced to consider short-range ordering (SRO) within the melt, whereas the solid solution was modeled based on the Compound Energy Formalism. Literature data on phase equilibria and thermochemical properties were critically evaluated and used during the optimization of thermodynamic parameters for KCl-LiCl-NaCl and KCl-LiCl-NdCl 3 and their subsystems. The calculated phase diagrams and mixing enthalpies are in good agreement with the experimental data. The thermodynamic modeling for the KCl-LiCl-NdCl 3 system was carried out for the first time. To fill the gap in experimental measurement, enthalpy of mixing for the KCl-LiCl-NdCl 3 melt was estimated using the surrounded-ion model. These data then served as critical inputs for thermodynamic optimization. Furthermore, the present study can provide insights into thermodynamic property evolution of the electrolyte and solubility limit of various impurities during the electrorefining process.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Design metastability in high-entropy alloys by tailoring unstable fault energies

Metastable alloys with transformation-/twinning-induced plasticity (TRIP/TWIP) can overcome the strength-ductility trade-off in structural materials. Originated from the development of traditional alloys, the intrinsic stacking fault energy (ISFE) has been applied to tailor TRIP/TWIP in high-entropy alloys (HEAs) but with limited quantitative success. Here, we demonstrate a strategy for designing metastable HEAs and validate its effectiveness by discovering seven alloys with experimentally observed metastability for TRIP/TWIP. We propose unstable fault energies as the more effective design metric and attribute the deformation mechanism of metastable face-centered cubic alloys to unstable martensite fault energy (UMFE)/unstable twin fault energy (UTFE) rather than ISFE. Among the studied HEAs and steels, the traditional ISFE criterion fails in more than half of the cases, while the UMFE/UTFE criterion accurately predicts the deformation mechanisms in all cases. The UMFE/UTFE criterion provides an effective paradigm for developing metastable alloys with TRIP/TWIP for an enhanced strength-ductility synergy.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Predicting melt pool depth and grain length using multiple signatures from in-situ single camera two-wavelength imaging pyrometry for laser powder bed fusion

In laser powder bed fusion (LPBF), the in-situ process signatures are known to have a direct correlation with the microstructural properties of the solidified melt pool (MP). It is known that the MP cooling and heating rates, and laser processing parameters can critically determine the grain structure and thereby affect the part properties. The objective of this work is to study the feasibility of using in-process, high-speed imaging pyrometry for evaluating the solidified MP properties “below” the surface, such as depth and microstructural properties. To accomplish this, we employ an in-house single camera-based two-wavelength imaging pyrometry (STWIP) system for monitoring the printing of single-scan tracks with Inconel 718 on a commercial LPBF printer (EOS M290). Further, the lab designed STWIP system is a coaxial high-speed (>10,000 fps) imaging system capable of monitoring MP temperature, morphology, and intensity profiles. The temperature measurements from STWIP are emissivity independent. The STWIP measured MP signatures of the printed tracks are correlated with the ex-situ microscopy characterized MP depth and the average grain lengths. From the data analysis, using support vector machine (SVM)-based regression models, we found that the MP temperature signatures are crucial for an accurate prediction of MP depth and the grain length, thus validating the novelty and necessity of the developed in-situ monitoring methods and analysis.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Determination of Location-Specific Solidification Cracking Susceptibility for a Mixed Dissimilar Alloy Processed by Wire-Arc Additive Manufacturing

Solidification cracking is a major obstacle when joining dissimilar alloys using additive manufacturing. In this work, location-specific solidification cracking susceptibility has been investigated using an integrated computational materials engineering (ICME) approach for a graded alloy formed by mixing P91 steel and Inconel 740H superalloy. An alloy mixture of 26 wt.% P91 and 74 wt.% Inconel 740H, with high configurational and total entropy, was fabricated using wire arc additive manufacturing. Microstructure characterization revealed intergranular solidification cracks in the FCC matrix, which increased in length along with the enrichment of Nb (~27 to 56 wt.%) and Cu (~87 wt.%) in the middle and top regions. DICTRA simulations to model location-specific solidification cracking susceptibility showed that the top region with the highest cooling rate (270 K/s) has the highest solidification cracking susceptibility in comparison with the middle and bottom regions. This is in good agreement with the experimentally observed varying crack length. From Scheil simulations, it was deduced that enrichment of Nb and Cu affected the solidification range as high as ~77%, in comparison with the matrix composition. The overall solidification cracking susceptibility and freezing range was highest for the 26 wt.% P91 alloy amongst the mixed compositions between P91 steel and 740H superalloy, proving that solidification characteristics play a major role in alloy design for additive manufacturing.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2021

Interfacial characteristics of P91 steel - Inconel 740H bimetallic structure fabricated using wire-arc additive manufacturing

Although bimetallic structures can offer unique solutions to engineering problems with varying functionality, joining two dissimilar alloys using additive manufacturing involves challenges such as cracking and segregation. In this work, bimetallic structures of Inconel 740H superalloy and P91 steel are processed using wire-arc additive manufacturing (WAAM) for the first time. P91 steel is directly deposited over 740H with a cooling time of 20 minutes in between the two depositions. During microstructure characterization, a large gradient zone with coarse grains spanning for ~2200 μm is observed. Moreover, the microhardness of the gradient zone is the least in comparison with the P91 and 740H deposits. No deleterious phase formation is found; however, intergranular cracks are observed along the gradient zone. In order to deduce the reason for cracking, non-equilibrium solidification simulations are performed for the mixed compositions of P91 and 740H in the gradient zone. Here, the reasons for crack formation in the gradient zone are the sudden change in the volumetric coefficient of thermal expansion due to the formation of MC carbides as well as the development of local strains from the thermal residual stresses. Therefore, altering the deposition sequence and introducing gradient layers with mixed composition between the P91 and 740H deposits will be beneficial in achieving defect-free builds. Through the integration of experiments and simulation, this work gains valuable insights into the processability of dissimilar alloy manufacturing using the WAAM technique.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2020

A Discrete Dendrite Dynamics Model for Epitaxial Columnar Grain Growth in Metal Additive Manufacturing with Application to Inconel

Epitaxial columnar grain growth is a prevalent microstructural feature in the additive manufacturing (AM) of metal components such as Inconel, with cubic unit cell crystal lattice structure (face centered cubic (FCC) or body centered cubic (BCC)). These columnar grains evolve from the partly molten grains in the substrate or the solidified metal. This work proposes an efficient model to simulate the competitive growth of epitaxial columnar dendritic grains. The proposed model tracks the dynamic changes in the dendrites emanating from discrete points along the solid/liquid interface of a quasi-steady melt pool (MP). These dynamic changes include convergence and divergence of growing dendrites. The model is extended to predict the microstructure of large 3D parts and experimentally validated by comparing the simulation results for laser powder bed fusion (L-PBF) and wire-arc additive manufacturing (WAAM) processes. The microstructure and pole figures are predicted for Inconel 718 samples produced by L-PBF and Inconel 740H samples produced by WAAM processes. Finally, the model predictions compare well with the observed microstructure and pole figures results for both the L-PBF and WAAM processes.

20 FOSSIL-FUELED POWER PLANTS↗