Search NASA⌕ Search

Engineering topics

Srinivasan, R.

Publications and source records attributed to Srinivasan, R..

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Experiments in dilution jet mixing - Effects of multiple rows and non-circular orifices

Experimental and empirical model results are presented that extend previous studies of the mixing of single-sided and opposed rows of jets in a confined duct flow to include effects of non-circular orifices and double rows of jets. Analysis of the mean temperature data obtained in this investigation showed that the effects of orifice shape and double rows are significant only in the region close to the injection plane, provided that the orifices are symmetric with respect to the main flow direction. The penetration and mixing of jets from 45-degree slanted slots is slightly less than that from equivalent-area symmetric orifices. The penetration from two-dimensional slots is similar to that from equivalent-area closely-spaced rows of holes, but the mixing is slower for the 2-D slots. Calculated mean temperature profiles downstream of jets from non-circular and double rows of orifices, made using an extension developed for a previous empirical model, are shown to be in good agreement with the measured distributions.

Holdeman, J. D.↗
NASA NTRS1985

Simulation of a G-tolerance curve using the pulsatile cardiovascular model

A computer simulation study, performed to assess the ability of the cardiovascular model to reproduce the G tolerance curve (G level versus tolerance time) is reported. A composite strength duration curve derived from experimental data obtained in human centrifugation studies was used for comparison. The effects of abolishing automomic control and of blood volume loss on G tolerance were also simulated. The results provide additional validation of the model. The need for the presence of autonomic reflexes even at low levels of G is pointed out. The low margin of safety with a loss of blood volume indicated by the simulation results underscores the necessity for protective measures during Shuttle reentry.

Solomon, M.↗
NASA NTRS1985

Experiments in dilution jet mixing effects of multiple rows and non-circular orifices

Experimental and empirical model results are presented that extend previous studies of the mixing of single-sided and opposed rows of jets in a confined duct flow to include effects of non-circular orifices and double rows of jets. Analysis of the mean temperature data obtained in this investigation showed that the effects of orifice shape and double rows are significant only in the region close to the injection plane, provided that the orifices are symmetric with respect to the main flow direction. The penetration and mixing of jets from 45-degree slanted slots is slightly less than that from equivalent-area symmetric orifices. The penetration from 2-dimensional slots is similar to that from equivalent-area closely-spaced rows of holes, but the mixing is slower for the 2-D slots. Calculated mean temperature profiles downstream of jets from non-circular and double rows of orifices, made using an extension developed for a previous empirical model, are shown to be in good agreement with the measured distributions.

Holdeman, J. D.↗
NASA NTRS1984

NASA dilution jet mixing, phase 3

Many of the gas turbine combustors in operation use multiple rows of dilution jets, and some have geometries that are different from circular holes. The data base available in literature is generally applicable to a single row of circular holes. Tests were performed with uniform mainstream conditions for several orifice plate configurations. Temperature and pressure measurements were made in the test section at 4 axial and 11 transverse stations. These measurements were made with a 60-element rake probe. Test results for some of these cases are discussed.

Srinivasan, R.↗
NASA NTRS1984

Dilution jet mixing program

Parametric tests were conducted to quantify the mixing of opposed rows of jets (two-sided injection) in a confined cross flow. Results show that jet penetrations for two sided injections are less than that for single-sided injections, but the jet spreading rates are faster for a given momentum ratio and orifice plate. Flow area convergence generally enhances mixing. Mixing characteristics with asymmetric and symmetric convergence are similar. For constant momentum ratio, the optimum S/H(0) with in-line injections is one half the optimum value for single sided injections. For staggered injections, the optimum S/H(0) is twice the optimum value for single-sided injection. The correlations developed predicted the temperature distributions within first order accuracy and provide a useful tool for predicting jet trajectory and temperature profiles in the dilution zone with two-sided injections.

Srinivasan, R.↗
NASA NTRS1984

On modeling dilution jet flowfields

This paper compares temperature field measurements from selected experiments on a single row, and opposed rows, of jets injected into a ducted crossflow with profiles calculated using an empirical model based on assumed vertical profile similarity and superposition, and distributions calculated with a 3-D elliptic code using a standard K-E turbulence model. The empirical model predictions are very good within the range of the generating experiments, and the numerical model results, although exhibiting too little mixing, correctly describe the effects of the principal flow and geometric variables.

Holdeman, J. D.↗
NASA NTRS1984

Modeling of dilution jet flowfields

The present paper will compare temperature field measurements from selected cases in these investigations with distributions calculated with an empirical model based on assumed vertical profile similarity and superposition and with a 3-D elliptic code using a standard K-E turbulence model. The results will show the capability (or lack thereof) of the models to predict the effects of the principle flow and geometric variables.

Holdeman, J. D.↗
NASA NTRS1984

On modeling dilution jet flowfields

This paper compares temperature field measurements from selected experiments on a single row, and opposed rows, of jets injected into a ducted crossflow with profiles calculated using an empirical model based on assumed vertical profile similarity and superposition, and distributions calculated with a 3-D elliptic code using a standard K-E turbulence model. The empirical model predictions are very good within the range of the generating experiments, and the numerical model resultings, although exhibiting too little mixing, correctly describe the effects of the principal flow and geometric variables.

Holdeman, J. D.↗
NASA NTRS1983

Executive summary, aerothermal modeling program, phase 1

Submodels used in the combustor analytical models that were successfully used in designing advanced technology combustors were assessed. Specific recommendations for further improvement of model accuracy for combustor design purposes were made. Based upon an exhaustive literature survey, a number of test cases were selected to assess accuracy of submodels of turbulence, turbulence/chemistry interaction, spray combustion, and dilution jet mixing processes within a confined cross-stream. These test cases included simple flows and complex flows with and without swirl. Nonrecirculating and recirculating, and nonreactive and reactive flows were investigated. It was concluded that the current models give qualitative trends for the recirculating secondary flows (as encountered in a gas turbine combustor primary zone), but the predictions are good for the dilution zone.

Srinivasan, R.↗
NASA NTRS1983

Aerothermal modeling program, phase 1

Aerothermal submodels used in analytical combustor models are analyzed. The models described include turbulence and scalar transport, gaseous full combustion, spray evaporation/combustion, soot formation and oxidation, and radiation. The computational scheme is discussed in relation to boundary conditions and convergence criteria. Also presented is the data base for benchmark quality test cases and an analysis of simple flows.

Srinivasan, R.↗
NASA NTRS1983

Aerothermal modeling program, phase 1

The combustor performance submodels for complex flows are evaluated. The benchmark test cases for complex nonswirling flows are identified and analyzed. The introduction of swirl into the flow creates much faster mixing, caused by radial pressure gradients and increase in turbulence generation. These phenomena are more difficult to predict than the effects due to geometrical streamline curvatures, like the curved duct, and sudden expansion. Flow fields with swirl, both confined and unconfined are studied. The role of the dilution zone to achieve the turbine inlet radial profile plays an important part, therefore temperature field measurements were made in several idealized dilution zone configurations.

Srinivasan, R.↗
NASA NTRS1983

Experiments in dilution jet mixing

Experimental results are given on the mixing of a single row of jets with an isothermal mainstream in a straight duct, to include flow and geometric variations typical of combustion chambers in gas turbine engines. The principal conclusions reached from these experiments were: at constant momentum ratio, variations in density ratio have only a second-order effect on the profiles; a first-order approximation to the mixing of jets with a variable temperature mainstream can be obtained by superimposing the jets-in-an isothermal-crossflow and mainstream profiles; flow area convergence, especially injection-wall convergence, significantly improves the mixing; for opposed rows of jets, with the orifice centerlines in-line, the optimum ratio of orifice spacing to duct height is one half of the optimum value for single side injection at the same momentum ratio; and for opposed rows of jets, with the orifice centerlines staggered, the optimum ratio of orifice spacing to duct height is twice the optimum value for single side injection at the same momentum ratio.

Holdeman, J. D.↗
NASA NTRS1983

Experiments in dilution jet mixing

Experimental results are presented on the mixing of a single row of jets with an isothermal mainstream in a straight duct, with flow and geometric variations typical of combustion chambers in gas turbine engines included. It is found that at a constant momentum ratio, variations in the density ratio have only a second-order effect on the profiles. A first-order approximation to the mixing of jets with a variable temperature mainstream can, it is found, be obtained by superimposing the jets-in-an-isothermal-crossflow and mainstream profiles. Another finding is that the flow area convergence, especially injection-wall convergence, significantly improves the mixing. For opposed rows of jets with the orifice cone centerlines in-line, the optimum ratio of orifice spacing to duct height is determined to be 1/2 of the optimum value for single injection at the same momentum ratio. For opposed rows of jets with the orifice centerlines staggered, the optimum ratio of orifice spacing to duct height is found to be twice the optimum value for single side injection at the same momentum ratio.

Holdeman, J. D.↗
NASA NTRS1983

Simulation of cardiovascular response to acceleration stress following weightless exposure

Physiological adjustments taking place during space flight tend to reduce the tolerance of the crew to headward (+Gz) acceleration experienced during the reentry phase of the flight. This reduced tolerance to acceleration stress apparently arises from an adaptation to the microgravity environment of space, including a decrease in the total circulating blood volume. Countermeasures such as anti-g garments have long been known to improve the tolerance to headward g-force, but their effectiveness in space flight has not been fully evaluated. The simulation study presented in this paper is concerned with the response of the cardiovascular system to g-stress following cardiovascular deconditioning, resulting from exposure to weightlessness, or any of its ground-based experimental analogs. The results serve to demonstrate the utility of mathematical modeling and computer simulation for studying the causes of orthostatic intolerance and the remedial measures to lessen it.

Srinivasan, R.↗
NASA NTRS1982

Dilution Jet Mixing Program, phase 1

The effect of jet to mainstream density ratio, flow area convergence as encounted in transition sections, and nonuniform mainstream profile upstream of dilution orifices on the mixing of a row of jets with a confined cross flow was quantified. It is found that: (1) jet spreading rate in transverse direction is increased with increasing J, H/D and with decreasing S/D; (2) the density ratio has only a second order effect on the jet mixing characteristics for a constant momentum ratio; (3) the temperature distributions in the jet mixing region are strongly influenced by the undisturbed mainstream profile; (4) flow area convergence enhances mixing in radial and transverse directions. An asymmetric convergent duct with flat wall injection has the same jet mixing characteristics as a symmetric convergent duct. An asymmetric convergent duct with slant wall injection has a faster jet spreading rate in the transverse direction.

Srinivasan, R.↗
NASA NTRS1980

Numerical computations of swirling recirculating flow

Swirling, recirculating, nonreacting flows were computed using a 2D elliptic program consisting of three tasks. The computations in Task 1 and 2 were made using an independent analysis for the two coaxial swirling flows. The Task 2 computations were made using the measured profiles of the mixing region. In Task 3, a modified 2D elliptic program was employed to include the effects of interaction between the inner and outer streams.

Srinivasan, R.↗
NASA NTRS1977

Turbulent plane Couette flow using probability distribution functions

A numerical scheme employing a combination of the discrete ordinate method and finite differences is developed for solving the one-dimensional form of Lundgren's (1967) model equation for turbulent plane Couette flow. The approach used requires no a priori assumption about the form of the turbulent distribution function, and the numerical solution is obtained directly from the governing differential equations. Two different types of boundary conditions (zero-gradient and Chapman-Enskog) for the distribution function are evaluated by comparing the numerical results with experimental data. It is found that: (1) the present approach gives convergent and stable results over a wide range of Reynolds numbers; (2) Lundgren's equation yields results that compare well with experimental data for mean velocity and skin friction in the case of simple Couette flow; (3) the zero-gradient boundary condition leads to a logarithmic flow profile; and (4) the Chapman-Enskog boundary condition provides very good agreement with experimental data when applied within the near-wall region.

Srinivasan, R.↗