Search NASA⌕ Search

Engineering topics

Srinivasan, Venkat

Publications and source records attributed to Srinivasan, Venkat.

14 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Minimizing Interfacial Resistance between Polymer Electrolytes and Metal Electrodes Using Applied Current

Reducing the interfacial resistance between different phases in electrochemical systems is crucial for enabling practical applications. In this work, we proposed a process for reducing the interfacial resistance between polymer electrolytes and metal electrodes. Thus far in the literature, the lowest interfacial resistance reported in these systems is 15 Ω·cm2. In this study, assembled and preconditioned symmetric cells with lithium–indium alloy electrodes showed similar values. The current through the cell was increased in steps up to the limiting current. This resulted in a permanent decrease of the interfacial resistance to values as low as 1 Ω·cm2, a value that is comparable to that of optimized lithium-ion batteries. The proposed process is general, and it could be applied to any combination of polymer electrolytes and metal electrodes.

Lee, Jaeyong↗
DOE OSTI2024

Designing Particle Morphologies for Materials with Solid Transport Limitations: A Case Study of Lithium and Manganese Rich Cathode Oxides

A lithium and manganese rich nickel-manganese-cobalt oxide (LMR-NMC) cathode is a promising candidate for next-generation batteries due to its high specific capacity, low cost, and low cobalt content. However, the material suffers from poor rate capability due to the diffusion limitations of lithium in the cathode particles. Understanding the material performance requires careful control of the morphology of the cathode particles, taking into account the primary and agglomerated diffusion pathways and the presence of pores, some of which could be closed from electrolyte infiltration. Here, in this study, we use a microstructure-based mathematical model combined with experimental data to understand the role of the complex cathode particle morphology in the rate performance of the material. Scanning electron microscopy images of cathodes made under different synthesis conditions, which results in different agglomerate morphologies, serve as the input into the mathematical model. The model is then compared to rate data to understand the controlling parameters. The presence of intra-agglomerate closed pores results in a large agglomerate diffusion length in comparison to the ideal condition, where the primary particles are agglomerated in an open and dispersed manner such that the entire interfacial area is available for electrochemical reaction. Smaller primary and agglomerate diffusion lengths result in better electrochemical performance. This points us toward designing the morphology of the cathode particles to compensate for the diffusion limitation of LMR-NMC while maximizing the density.

Tewari, Deepti↗
DOE OSTI2024

Stable, Impermeable Hexacyanoferrate Anolyte for Nonaqueous Redox Flow Batteries

Redox-active molecules, or redoxmers, in nonaqueous redox flow batteries often suffer from membrane crossover and low electrochemical stability. Transforming inorganic polyionic redoxmers established for aqueous batteries into nonaqueous candidates is an attractive strategy to address these challenges. Here, in this study, we demonstrate such tailoring for hexacyanoferrate (HCF) by pairing the anions with tetra-n-butylammonium cation (TBA + ). TBA 3 HCF has good solubility in acetonitrile and >1 V lower redox potential vs the aqueous counterpart; thus, the familiar aqueous catholyte becomes a new nonaqueous anolyte. The lowering of redox potential correlates with replacement of water by acetonitrile in the solvation shell of HCF, which can be traced to H-bond formation between water and cyanide ligands. Symmetric flow cells indicate exceptional stability of HCF polyanions in nonaqueous electrolytes and Nafion membranes completely block HCF crossover in full cells. Ion pairing of metal complexes with organic counterions can be effective for developing promising redoxmers for nonaqueous flow batteries.

25 ENERGY STORAGE↗
DOE OSTI2024

Modeling Analysis of Ball-Milling Process for Battery-Electrode Synthesis

The mechanical alloying process is a promising method for synthesizing electrode materials for batteries owing to its benefits such as the ability to produce nanostructured, high-performing electrode alloys, no adverse effects on the solid electrolyte for solid-state batteries, stable production of thick electrodes, simple processing steps, and low processing costs. It is gaining intensive attention in the battery industry as one of the best methods to replace the conventional wet-slurry-solvent method, and its application is rapidly increasing these days. However, the operation is currently conducted purely based on trial-and-error methods without fully utilizing the features of its functions. Here, this may be attributed to a lack of understanding of the effect of operating parameters on the alloying process and final products. Surprisingly, there is a scarcity of the literature conducting fundamental research to comprehend the underlying physics of the entire mechanical alloying process, resulting in a significant knowledge gap. To address this knowledge gap, extensive research was conducted. The existing literature on mechanical alloying was reviewed to comprehend the current state of understanding and to discuss the direction for future research. Mathematical expressions were developed to create physics-based models capable of capturing the entire mechanical alloying process, including milling kinetics and defect-enhanced phase evolution. These methods were then applied to investigate the impact of operating parameters such as milling frequency, initial mole ratio of the alloyed materials, density of grinding balls, and energy required for the powders to become amorphous (i.e., the amorphization energy threshold). This research aimed not only to comprehend the direct effects of these operating parameters but also to unveil the physics underlying the ball-milling process. The results of our study can serve as crucial information for the battery industry in designing or operating the ball-milling process.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Deciphering the morphology of transition metal carbonate cathode precursors

The performance and life of Li-ion battery cathode materials are determined by both the composition (crystal structure and transition metal ratio) and the morphology (particle size, size distribution, and surface area). Careful control of these two aspects is the key to long lasting, high-energy batteries that can undergo fast charge. Developing such cathodes requires manipulation of the synthesis conditions, namely the coprecipitation process to develop the precursor and a calcination step to lithiate and convert it to a transition metal oxide. In this paper, we utilize a combination of controlled synthesis, microscopic and spectroscopic characterization, and multi-scale mathematical modeling to shed light on the synthesis of cathode precursors. The complex interplay between the various chemical reactions in the co-precipitation process is studied to provide experimentalists with guidance on achieving composition control during synthesis. Further, the formation of a variety of morphologies of the primary particles and the driving force for agglomeration is mathematically described, for the first time, based on an energy minimization approach. Results suggest that the presence of Ni and/or Co significantly lowers the reaction rate constant compared to Mn, resulting in agglomerated growth in the former and single crystal growth in the latter. Modeling studies are used to provide a phase map describing the synthesis conditions needed to control the secondary particle size and corresponding size distribution. Finally, this paper represents an important step in developing a computationally guided approach to the synthesis of battery cathode materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Unveiling Morphology and Crystallinity Dynamics in Ni x Mn 1– x CO 3 Cathode Precursors through Batch-Mode Coprecipitation

This study delves into the synthesis and control of Ni x Mn 1–x CO 3 , a critical class of Mn-rich, Co-free precursors vital for cathode-oxide materials in energy storage and conversion technologies. Employing batch-mode coprecipitation, we systematically generated samples with varying Ni concentrations (x = 0, 0.1, 0.3, 0.5, 0.7, and 0.9) and conducted a comprehensive analysis of their compositions, crystallinities, transition-metal distributions, and particle morphologies through both experimental and computational methods. A significant variation in particle size and crystallinity was observed, contingent on the Ni content. Further, a pivotal transition emerged at Ni concentrations above x = ~0.5, transforming uniform morphologies, such as spherical, monodisperse, pseudo-single-crystalline particles, into bimodal, polycrystalline structures. Furthermore, the study highlights the role of Ni–ammonia complexes leading to Ni-deficient precipitates and underscores the importance of ammonia concentration in achieving precise Ni content control. This study unveils critical reaction conditions governing Mn-rich precursor properties that are vital for cathode-oxides, emphasizing the need for meticulous synthetic control and offering the potential for practical applications in advanced energy storage and conversion systems.

25 ENERGY STORAGE↗
DOE OSTI2024

In Situ Insights into Cathode Calcination for Predictive Synthesis: Kinetic Crystallization of LiNiO 2 from Hydroxides

Abstract Calcination is a solid‐state synthesis process widely deployed in battery cathode manufacturing. However, its inherent complexity associated with elusive intermediates hinders the predictive synthesis of high‐performance cathode materials. Here, correlative in situ X‐ray absorption/scattering spectroscopy is used to investigate the calcination of nickel‐based cathodes, focusing specifically on the archetypal LiNiO 2 from Ni(OH) 2 . Combining in situ observation with data‐driven analysis reveals concurrent lithiation and dehydration of Ni(OH) 2 and consequently, the low‐temperature crystallization of layered LiNiO 2 alongside lithiated rocksalts. Following early nucleation, LiNiO 2 undergoes sluggish crystallization and structural ordering while depleting rocksalts; ultimately, it turns into a structurally‐ordered layered phase upon full lithiation but remains small in size. Subsequent high‐temperature sintering induces rapid crystal growth, accompanied by undesired delithiation and structural degradation. These observations are further corroborated by mesoscale modeling, emphasizing that, even though calcination is thermally driven and favors transformation towards thermodynamically equilibrium phases, the actual phase propagation and crystallization can be kinetically tuned via lithiation, providing freedom for structural and morphological control during cathode calcination.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Study of Void Formation at the Lithium|Solid Electrolyte Interface

There is growing recognition of the critical role of void formation in lithium metal anodes in solid-state batteries and its impact on electrochemical performance. While experimental studies have demonstrated the challenges ensuing from void formation at the lithium metal interface with the solid electrolyte, there is a need to understand and quantify the role of intrinsic transport properties in lithium metal and the impact of external stimuli, such as temperature, pressure, and current density. Here, we develop this understanding by constructing a phase field-based model that captures the evolution of void domains at the lithium-solid electrolyte interface. Growth of the pores is driven by the fast removal of lithium from the interface during stripping at high current densities. Relative magnitudes of the bulk and surface lithium diffusivities, along with the applied current density, dictate the final pore morphology. Increasing the temperature results in faster diffusion, while external applied pressure causes creep flow of lithium, both of which help to mitigate the evolution of voids by quickly transporting metal from the bulk to the interface. Finally, a phase map as a function of temperature and pressure is developed as a guide to determine the regions that can lead to the stable cycling of lithium metal.

25 ENERGY STORAGE↗
DOE OSTI2024

Phase Field Modeling of Pressure Induced Densification in Solid Electrolytes

Adoption of dense and homogeneous solid electrolytes can possibly mitigate the propagation of lithium dendrites and enable lithium metal anodes. Application of external pressure helps to minimize the sintering temperature in oxide ceramics and can potentially densify softer sulfide electrolytes even under room temperature conditions. Here, a previously developed phase field-based computational scheme for predicting the high-temperature sintering-induced densification of oxide ceramic solid electrolytes is extended in the present context to capture the influence of external pressure for densifying solid electrolytes. Two different bulk deformation mechanisms, namely, "reorganization" and "creep deformation," are dominant under external pressure, which is different from the surface and grain-boundary diffusion-induced densification of solid electrolytes that occurs during high temperature sintering. External pressure also increases the points of contact between the particles, which further enhances the propensity of diffusion-induced sintering process. Results obtained from simulations indicate that densification under external pressure is independent of the solid electrolyte particle morphology. Finally, a phase map is generated between applied pressure and temperature for achieving complete densification of oxide ceramics, which can possibly guide the synthesis of thin and dense solid electrolyte separators.

25 ENERGY STORAGE↗
DOE OSTI2024

Cobalt-free composite-structured cathodes with lithium-stoichiometry control for sustainable lithium-ion batteries

Abstract Lithium-ion batteries play a crucial role in decarbonizing transportation and power grids, but their reliance on high-cost, earth-scarce cobalt in the commonly employed high-energy layered Li(NiMnCo)O 2 cathodes raises supply-chain and sustainability concerns. Despite numerous attempts to address this challenge, eliminating Co from Li(NiMnCo)O 2 remains elusive, as doing so detrimentally affects its layering and cycling stability. Here, we report on the rational stoichiometry control in synthesizing Li-deficient composite-structured LiNi 0.95 Mn 0.05 O 2 , comprising intergrown layered and rocksalt phases, which outperforms traditional layered counterparts. Through multiscale-correlated experimental characterization and computational modeling on the calcination process, we unveil the role of Li-deficiency in suppressing the rocksalt-to-layered phase transformation and crystal growth, leading to small-sized composites with the desired low anisotropic lattice expansion/contraction during charging and discharging. As a consequence, Li-deficient LiNi 0.95 Mn 0.05 O 2 delivers 90% first-cycle Coulombic efficiency, 90% capacity retention, and close-to-zero voltage fade for 100 deep cycles, showing its potential as a Co-free cathode for sustainable Li-ion batteries.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Comparing Experimentally-Measured Sand’s Times with Concentrated Solution Theory Predictions in a Polymer Electrolyte

We compare the electrochemically measured Sand’s time, the time required for the cell potential to diverge when the applied current density exceeds the limiting current, with theoretical predictions for a 0.47 M poly(ethylene oxide) (5 kg mol −1 )/LiTFSI electrolyte. The theoretical predictions are made using concentrated solution theory which accounts for both concentration polarization and polymer motion, using independently measured parameters that depend on concentration, c : conductivity ( κ ), salt diffusion coefficient ( D ), cationic transference number with respect to the solvent velocity ( t + 0 ), thermodynamic factor 1 + dln f ± dln c , and partial molar volume of the salt ( V ̅ ); f ± is the mean molar activity coefficient of the salt. We find quantitative agreement between experimental data and theoretical predictions. We derive a generalized analytical expression for Sand’s time for electrolytes based on dilute solution theory. This expression correctly predicts the divergence of the Sand’s time at the limiting current, in agreement with experimental data and concentrated solution theory predictions. When the applied current is large compared to the limiting current, the analytical expression approaches the standard expression for Sand’s time used in the literature.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

The phantom menace of dynamic soft-shorts in solid-state battery research

Solid-state batteries with lithium metal anodes present the highest energy density batteries for applications in electric vehicles, leading to massive R&D investments over the past decade. Although most research focuses on preventing lithium metal dendrites that eventually short the battery, the nature of these shorts remains elusive. Soft-shorts, in particular, receive little attention or are not recognized, even in published data. Here, in this study, we present a comprehensive outline of the detection and analysis of soft -shorts in solid-state lithium metal cells with composite polymer electrolytes as well as a fundamental understanding of the dynamics of soft -shorts. Transient un-shorting of soft -shorts that occurs on the micro-to-millisecond timescale-driven by joule heating, chemical reactivity, and other processes-limits one's ability to determine whether the cell was or is still shorted. We provide numerous experimental methods to detect and analyze soft-shorts in any battery type as a resource to all battery researchers.

25 ENERGY STORAGE↗
DOE OSTI2023

How machine learning can extend electroanalytical measurements beyond analytical interpretation

Electroanalytical measurements are routinely used to estimate material properties exhibiting current and voltage signatures. Analysis of such measurements relies on analytical expressions of material properties to describe the experiments. The need for analytical expressions limits the experiments that can be used to measure properties as well as the properties that can be estimated from a given experiment. Such analytical relations are essentially solutions of the physics-based differential equations (with properties as coefficients) describing the material behavior under certain specific conditions. In recent years, a new machine learning-based approach has been gaining popularity wherein the differential equations are numerically solved to interpret the electroanalytical experiments in terms of corresponding material properties. Since the physics-based differential equations are solved, one can additionally estimate underlying fields, e.g., concentration profile, using such an approach. To exemplify the characteristics of such a machine learning assisted interpretation of electroanalytical measurements, we use data from the Hebb–Wagner test on a magnesium spinel intercalation host. In conclusion, as compared to the traditional analytical expression-based interpretation, the emerging approach decreases experimental efforts to characterize relevant material properties as well as provides field information that was previously inaccessible.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗