Search NASA⌕ Search

Engineering topics

Stach, Eric

Publications and source records attributed to Stach, Eric.

At least 19 records

Higher loadings of Pt single atoms and clusters over reducible metal oxides: application to C–O bond activation

We develop higher loadings of isolated noble metal atoms and clusters on a mildly reducible metal oxide. Here we demonstrate the approach for Pt supported on TiO 2 and confirmed it by XRD, AC-HAADF-STEM, CO-FTIR, XAS, and XPS. Density functional theory calculations rationalize the experimental stability and the IR shifts using mixtures of CH 3 I and CO. The redispersed catalysts are thermally stable in inert gas or H 2 and afford enhanced selectivity and activity in hydrodeoxygenation reactions compared to metal nanoparticles by creating surface oxygen vacancies that promote C–O cleavage without side reactions. Higher metal loadings, e.g., 1%Pt/TiO 2 , on the oxide surface profoundly increase the activity of the bare oxide catalyst tenfold compared to ultra-low loadings typically used for single atom catalysis.

36 MATERIALS SCIENCE↗

Autonomous experimentation systems for materials development: A community perspective

Solutions to many of the world's problems depend upon materials research and development. However, advanced materials can take decades to discover and decades more to fully deploy. Humans and robots have begun to partner to advance science and technology orders of magnitude faster than humans do today through the development and exploitation of closed-loop, autonomous experimentation systems. This review discusses the specific challenges and opportunities related to materials discovery and development that will emerge from this new paradigm. Our perspective incorporates input from stakeholders in academia, industry, government laboratories, and funding agencies. We outline the current status, barriers, and needed investments, culminating with a vision for the path forward. We intend the article to spark interest in this emerging research area and to motivate potential practitioners by illustrating early successes. We also aspire to encourage a creative reimagining of the next generation of materials science infrastructure. To this end, we frame future investments in materials science and technology, hardware and software infrastructure, artificial intelligence and autonomy methods, and critical workforce development for autonomous research.

36 MATERIALS SCIENCE↗

Epitaxial and Strong Support Interactions between Pt and LaFeO 3 Films Stabilize Pt Dispersion

The ability to stabilize very small Pt crystallites in supported-metal catalysts following harsh treatments is an important industrial problem. Herein, we demonstrate that Pt particles can be maintained in the 1- to 2-nm range following multiple oxidation and reduction cycles at 1073 K when the particles are supported on 0.5-nm LaFeO 3 films that have been deposited onto MgAl 2 O 4 using atomic layer deposition (ALD). Characterization by Scanning Transmission Electron Microscopy (STEM) suggest that, when the catalyst is oxidized at 1073 K, the Pt crystallites are oriented with respect to the underlying LaFeO 3 . X-Ray Absorption Spectroscopy (XAS) also shows evidence for changes in the Pt environment. CO-oxidation rates for the reduced catalyst remain unchanged after five redox cycles at 1073 K. Epitaxial growth of Pt clusters and the consequent strong metal-support interaction between Pt and LaFeO 3 are indicated to be prime reasons for the enhanced catalytic performances.

36 MATERIALS SCIENCE↗

Using in situ and operando methods to characterize phase changes in charged lithium nickel cobalt aluminum oxide cathode materials

Lithium ion batteries have been extensively explored in recent decades in order to improve their electrochemical performance, address safety concerns, and reduce costs in larger-scale applications. Electrode materials are key components which govern the properties of the battery at the system level. Cathode materials are of particular importance as they are a limiting factor for achieving high energy density. Lithium nickel cobalt aluminum oxide (LiNi 0.8 Co 0.15 Al 0.05 O 2 , referred to subsequently as NCA) is one of successful cathode materials since it can deliver higher capacity than other cathode materials such as lithium cobalt oxide or lithium iron phosphate. However, structural instabilities that occur NCA during charging or at high temperatures is believed to be the primary reason for performance degradation as well as a possible safety threat. Furthermore, understanding the structural evolution that occurs in NCA is of importance to acquire fundamental insights for taking full advantage of the high capacity of NCA materials. Beyond static information, in situ and operando characterization approaches allow us to observe structural changes under external stimulus or in a working condition, providing a deeper understanding of the routes by which structure evolve. In this review, we will describe the use of both in situ and operando characterization performed with both synchrotron X-ray based techniques and advanced electron microscopy, as the combination of these techniques have been shown to be particularly effective at providing structural information at complementary length scales.

25 ENERGY STORAGE↗

Probing enhanced lithium-ion transport kinetics in 2D holey nanoarchitectured electrodes

Nanostructuring has been proved effective towards improving many energy storage and conversion devices, and is feasible for a wide range of materials. In particular, secondary nanoarchitectured materials exhibit collective advantages compared with nano-sized primary building blocks. Despite the manifold efforts in designed nanoarchitectures and synthetic routes, the underlying ion diffusion kinetics and phase transformation behaviours within nanoarchitectures still remain less explored. Herein, we probed enhanced lithium-ion transport behaviours using 2D holey zinc ferrite (ZFO) nanosheets as a model material, to demonstrate how self-assembled 2D holey nanoarchitectured electrodes can feature efficient ion diffusion channels, robust yet continuous electron transfer framework, and enlarged surface area, contributing to the superior performance over the ZFO nanoparticles without secondary structures. By revealing kinetic parameters through combined spectroscopic measurements and electrochemical techniques, our study manifests increased lithium-ion diffusion coefficients, higher capacitive charge storage contribution and reduced charge transfer impedance in holey nanosheets compared to randomly aggregated nanoparticles. Furthermore, our results promote deeper understanding of significantly enhanced electrochemical energy storage properties of these 2D holey nanoarchitectured electrodes resulted from more uniform and complete phase transformation and better active material utilization.

25 ENERGY STORAGE↗

Highly active subnanometer Rh clusters derived from Rh-doped SrTiO 3 for CO 2 reduction

Here, sub-nanometer Rh clusters derived from Rh-doped SrTiO 3 , demonstrated by in-situ X-ray Diffraction (XRD) and X-ray Absorption Fine Structure (XAFS) measurements, are applied as highly active catalysts for CO 2 reduction. Compared to the supported Rh/SrTiO 3 , the catalyst synthesized by a doping-segregation method exhibits a higher space-time yield (STY) to CO with a selectivity of 95% for CO 2 reduction by hydrogen; it also shows a higher activity with a larger turnover frequency (TOF) for CO 2 reduction by ethane. According to the in-situ diffuse reflectance infrared Fourier transformed spectroscopy (DRIFTS) experiments, the higher CO selectivity for CO 2 hydrogenation is attributed to the lower CO binding strength resulted by the strong interactions (e.g., charge transfer) between Rh atoms and the oxide support with surface defects. The superior activity is suggested to be originated from the cooperative effect between the highly dispersed sub-nanometer Rh clusters for efficient dissociation of H 2 /C 2 H 6 and the reconstructed SrTiO 3 with oxygen vacancies for preferential adsorption/activation of CO 2 . Finally, the doping-segregation method provides a unique opportunity to tune the size of active metal clusters and the physicochemical properties of the oxide support, offering the potential for applications in a variety of chemical reactions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Molecular structure and sour gas surface chemistry of supported K 2 O/WO 3 /Al 2 O 3 catalysts

Molecular structures of the unprompted and K 2 O-promoted supported WO 3 /Al 2 O 3 catalysts were studied with in situ Raman and UV-vis spectroscopy. In situ Raman spectra revealed that supported 20% WO 3 /Al 2 O 3 corresponds to near monolayer coverage of isolated and oligomeric surface WOx species on Al 2 O 3 . Above monolayer surface WO x coverage (21% WO 3 /Al 2 O 3 ), crystalline WO 3 nanoparticles are also present. The addition of K 2 O to the supported WO 3 /Al 2 O 3 catalyst increased the concentration of isolated surface WO x species and did not form K 2 WO 4 nanoparticles. The reducibility of the tungsten oxide structures depends on their structures (2D or 3D) and the K 2 O promoter. Their interaction with acidic CO 2 and SO 2 gases was also investigated. Adsorption of CO 2 creates several surface carbonate species of varying acidity that were detected using a combination of in situ IR and mass spectroscopy. Adsorbed bicarbonate form on weakly basic surface sites on tungsten oxide monolayer WO 3 /Al 2 O 3 catalyst as well as in the presence of low 2.5% K 2 O loading. At high 5% K 2 O loading, the presence of the strong surface basic sites yields adsorbed carbonates. In conclusion, after SO 2 pretreatment, however, new strongly adsorbed sulfate appears on the surface that inhibit CO 2 adsorption.

36 MATERIALS SCIENCE↗

Capacity Fading Mechanism of the Commercial 18650 LiFePO 4 -Based Lithium-Ion Batteries: An in Situ Time-Resolved High-Energy Synchrotron XRD Study

In this paper, in situ high-energy synchrotron XRD studies were carried out on commercial 18650 LiFePO 4 cells at different cycles to track and investigate the dynamic, chemical, and structural changes in the course of long-term cycling to elucidate the capacity fading mechanism. The results indicate that the crystalline structural deterioration of the LiFePO 4 cathode and the graphite anode is unlikely to happen before capacity fades below 80% of the initial capacity. Rather, the loss of the active lithium source is the primary cause for the capacity fade, which leads to the appearance of inactive FePO 4 that is proportional to the absence of the lithium source. Our in situ HESXRD studies further show that the lithium-ion insertion and deinsertion behavior of LiFePO 4 continuously changed with cycling. For a fresh cell, the LiFePO 4 experienced a dual-phase solid-solution behavior, whereas with increasing cycle numbers, the dynamic change, which is characteristic of the continuous decay of solid solution behavior, is obvious. Finally, the unpredicted dynamic change may result from the morphology evolution of LiFePO 4 particles and the loss of the lithium source, which may be the cause of the decreased rate capability of LiFePO 4 cells after long-term cycling.

18650 cell↗

Impacts of Carrier Transport and Deep Level Defects on Delayed Cathodoluminescence in Droop-Mitigating InGaN/GaN LEDs

Prevalent droop mitigation strategies in InGaN-based LEDs require structural and/or compositional changes in the active region but are accompanied by a detrimental reduction in external quantum efficiency (EQE) due to increased Shockley-Read-Hall recombination. Understanding the optoelectronic impacts of structural modifications in InGaN/GaN quantum wells (QW) remains critical for emerging high-power LEDs. In this work, we use a combination of electron microscopy tools along with standard electrical characterization to investigate a wide range of low-droop InGaN/GaN QW designs. We find that chip-scale EQE is uncorrelated with extended well-width fluctuations observed in scanning transmission electron microscopy. Further, we observe delayed cathodoluminescence (CL) response from designs in which calculated band profiles suggest facile carrier escape from individual QWs. Samples with the slowest CL responses also exhibit the lowest EQEs and highest QW defect densities in deep level optical spectroscopy. We propose a model in which the electron beam (i) passivates deep level defect states and (ii) drives charge carrier accumulation and subsequent reduction of the built-in field across the multi-QW active region, resulting in delayed radiative recombination. Finally, we correlate CL rise dynamics with capacitance-voltage measurements and show that certain early-time components of the CL dynamics reflect the open circuit carrier population within one or more QWs.

Zhao, Zhibo↗

Report of the Basic Research Needs Workshop on Next Generation Electrical Energy Storage, March 27 – 29, 2017

The last decade has opened rich new horizons in electrical energy storage, with compelling impacts on society. Personal electronics have transformed from a novelty to a necessity. New options for transportation are burgeoning. In energy storage science, emerging new approaches are illuminating the inner workings of energy storage at the atomic and molecular scales with extensions to the meso and macro levels. The stage is set — with ripe new directions for basic energy storage science and promising new opportunities for energy storage for the electricity grid, transportation, the internet of things, and national defense. Next generation electrical energy storage could be as transformational for energy applications as lithium-ion batteries were for personal electronics. This report examines the opportunities in basic energy storage science that will bring this vision for the future to fruition. Sea changes are in the offing, moving from intuitive speculation to confirmed scientific knowledge, from trial-and-error serendipity to science-based design, and from qualitative models to quantitative predictions. To navigate towards these changes, Priority Research Directions (PRDs) were formulated by 175 leading scientists and engineers during a Basic Research Needs Workshop on Next Generation Electrical Energy Storage held in Gaithersburg, Maryland, on March 27-29, 2017. This diverse community included experts in theory, simulation, characterization, electrochemistry, and synthesis of electrochemically active materials and chemistries. They uncovered a rich horizon of compelling directions that promise to link diverse electrochemical phenomena (such as solvation, mobility, reactivity, and degradation) in a single interactive framework.

25 ENERGY STORAGE↗

Electrical Energy Storage Factual Status Document: Resource Document for the Workshop on Basic Research Needs for Next Generation Electrical Energy Storage, March 2017

Electrical energy storage is of growing importance to energy – with increasing use in transportation and on the electrical grid. Batteries are used in all types of vehicles, but have increased in importance with the growth of hybrid and all-electric powered vehicles. For the electrical grid, batteries have a wide diversity of applications from grid stability to storage of electricity generated when the load is low so it is available when there is more demand. Distributed generation of electricity by solar panels and wind generation are also drivers for enhanced energy storage. In both industries, a key enabler will be low-cost batteries with long life, excellent safety, and superior performance. In addition to these two big markets, consumer electronics powered by rechargeable batteries continues to grow into new areas with the advent of wearable technology, internet-of-things, and virtual reality. Today’s energy storage technologies fall far short of the requirements for many of these growing applications. Because of these technology gaps, advances in energy storage are expected to play a critical role for a secure energy future. This document was produced in preparation for a Department of Energy (DOE) Office of Basic Energy Sciences Workshop titled “Basic Research Needs for Next Generation Electrical Energy Storage.” This workshop will identify key basic research directions that could provide revolutionary breakthroughs needed for meeting future requirements for electrical energy storage. This document was intended to provide a high-level assessment of current technologies used for electrical storage—focusing specifically on batteries and electrochemical capacitors—and to define requirements that are foreseen for the future application of these technologies in transportation vehicles, stationary storage applications, and consumer electronics. Thus, it provides a common background for the workshop participants and sets the technological basis for the workshop.

25 ENERGY STORAGE↗

Mitigating Structural Defects in Droop-Minimizing InGaN/GaN Quantum Well Heterostructures

Modern commercial InGaN/GaN blue LEDs continue to suffer from efficiency droop, a reduction in efficiency with increasing drive current. External quantum efficiency (EQE) typically peaks at low drive currents (< 10 A cm 2 ) and drops monotonically at higher current densities, falling to <85% of the peak EQE at a drive current of 100 A cm 2 . Mitigating droop-related losses will yield tremendous gains in both luminous efficacy (lumens/W) and cost (lumens/$). Such improvements are critical for continued large-scale market penetration of LED technologies, particularly in high-power and high flux per unit area applications. However, device structures that reduce droop typically require higher indium content and are accompanied by a corresponding degradation in material quality which negates the droop improvement via enhanced Shockley-Read-Hall (SRH) recombination. In this work, we use advanced characterization techniques to identify and classify structural defects in InGaN/GaN quantum well (QW) heterostructures that share features with low-droop designs. Using aberration-corrected scanning transmission electron microscopy (C s -STEM), we find the presence of severe well width fluctuations (WWFs) in a number of low droop device architectures. However, the presence of WWFs does not correlate strongly with external quantum efficiency nor defect densities measured via deep level optical spectroscopy (DLOS). Hence, performance losses in the heterostructures of interest are likely dominated by nanoscale point or interfacial defects rather than large-scale extended defects.

36 MATERIALS SCIENCE↗

A method to determine fault vectors in 4H-SiC from stacking sequences observed on high resolution transmission electron microscopy images

A new method has been developed to determine the fault vectors associated with stacking faults in 4H-SiC from their stacking sequences observed on high resolution TEM images. This method, analogous to the Burgers circuit technique for determination of dislocation Burgers vector, involves determination of the vectors required in the projection of the perfect lattice to correct the deviated path constructed in the faulted material. Results for several different stacking faults were compared with fault vectors determined from X-ray topographic contrast analysis and were found to be consistent. This technique is expected to applicable to all structures comprising corner shared tetrahedra.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗