Search NASA⌕ Search

Engineering topics

Stalker, R. J.

Publications and source records attributed to Stalker, R. J..

42 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1987

High Reynolds number heat transfer to the cold walls of a model scramjet

The results of simultaneous heat transfer and pressure measurements at the walls of three different configurations of a model scramjet are presented. The heat transfer results are compared with results empirically predicted from the pressure measurements. It is shown that the measured heat transfer rate is comparable with, or lower than, that predicted for a laminar boundary layer. A mathematical model is proposed for the film-cooling effect observed when a hydrogen fuel is injected along a wall of the scramjet. In this mathematical model, the heat transfer rate is shown to be insensitive to the velocity profile in the insulating layer of fuel. The model suggests that the cooling layer is turbulent and that 90 percent of the fuel is mixed with the air.

Paull, A.↗
NASA NTRS1986

Further shock tunnel studies of scramjet phenomena

Scramjet phenomena were studied using the shock tunnel T3 at the Australian National University. Simple two dimensional models were used with a combination of wall and central injectors. Silane as an additive to hydrogen fuel was studied over a range of temperatures and pressures to evaluate its effect as an ignition aid. The film cooling effect of surface injected hydrogen was measured over a wide range of equivalence. Heat transfer measurements without injection were repeated to confirm previous indications of heating rates lower than simple flat plate predictions for laminar boundary layers in equilibrium flow. The previous results were reproduced and the discrepancies are discussed in terms of the model geometry and departures of the flow from equilibrium. In the thrust producing mode, attempts were made to increase specific impulse with wall injection. Some preliminary tests were also performed on shock induced ignition, to investigate the possibility in flight of injecting fuel upstream of the combustion chamber, where it could mix but not burn.

Morgan, R. G.↗
NASA NTRS1986

Hydrogen scramjet with side wall injection

Preliminary results are presented from an experimental evaluation of a hydrogen-burning wall-injection scramjet engine, performed in the free-piston shock tunnel at the Australian National University. The advantages of scramjet propulsion for high-Mach-number high-altitude flight are reviewed, and the need for an alternative to injection struts is indicated. Pressure profiles and heat-transfer measurements for constant-area and diverging ducts are presented graphically and characterized in detail. The ability of the injected flow to shield the chamber wall from the heat of the freestream flow is demonstrated. The extrapolation of the shock-tunnel results to flight conditions, however, is made difficult by the fact that a significant amount of fuel passes through a quenched zone without burning, seriously degrading overall performance.

Morgan, R. G.↗
NASA NTRS1985

Shock tunnel measurements of heat transfer in a model scramjet

The results of heat transfer measurements to the walls of a two dimensional scramjet combustion chamber in a shock tunnel are presented. Thin film heat transfer gauges on a ceramic glass substrate were used. The range of experimental conditions covered produced boundary layers ranging from laminar to transitional, as was independently checked by flow visualization. Empirical flat plate correlations, corrected for local pressure disturbances were used to make a comparison with the experimental results. In the fully laminar regime the heating rates were found to give approximate agreement with the empirical estimates. In the nonlaminar tests the heating rate is found to be well below the fully turbulent levels. It is not known at present if this is a transition effect, or if the pressure corrected flat plate turbulent correlations do not apply to the configuration used.

Morgan, R. G.↗
NASA NTRS1985

Scramjet sidewall burning: Preliminary shock tunnel results

Experiments performed with a two dimensional model scramjet with particular emphasis on the effect of fuel injection from a wall are reported. Air low with a nominal Mach number of 3.5 and varied enthalpies was produced. It was found that neither hydrogen injection angle nor combustor divergence angle had any appreciable effect on thrust values while increased combustor length appeared to increase thrust levels. Specific impulse was observed to peak when hydrogen was injected at an equivalence ratio of about 2. Lowering the Mach number of the injected hydrogen at low equivalence ratios, less than 4, appeared to benefit specific impulse while hydrogen Mach number had little effect at higher equivalence ratios. When a 1:1 mixture by volume of nitrogen and oxygen is used instead of air as a test gas, it is found that hydrogen combustion is enhanced but only at high enthalpies.

Morgan, R. G.↗