Search NASA⌕ Search

Engineering topics

Stan, Liliana

Publications and source records attributed to Stan, Liliana.

17 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Orientation-dependent structural properties during growth and growth mechanism of CoO films

The orientation-dependent local structural properties of CoO films on sapphire substrates during growth were investigated through linearly-polarized extended X-ray absorption fine structure (EXAFS) measurements. Specifically, CoO(1 1 1) and (100) crystals with a rock-salt structure (Fm3m) were epitaxially grown on alpha-Al2O3(0001) and (1012) substrates, respectively, at 700 degrees C using a radio-frequency sputtering system. The local structural properties of CoO films in the in-plane and out-of-plane orientations were quantitatively determined using linearly-polarized EXAFS at the Co K-edge during growth. The EXAFS analysis revealed that during the initial stages of growth, the local structural properties exhibit significant differences compared to thick films, with short atomic distances and large (small) Debye-Waller factors observed in the out-of-plane (in-plane) orientations. The local structural strain mostly diminished when approximately 20 CoO layers accumulated on the substrate. Density functional theory (DFT) calculations further supported these findings by confirming that cobalt atoms initially form stable bonds with the sapphire surface, leading to the simultaneous growth of oxygen and cobalt layers in a coordinated manner through layer-by-layer growth.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Enhanced Thermal Stability of Conductive Mercury Telluride Colloidal Quantum Dot Thin Films Using Atomic Layer Deposition

Colloidal quantum dots (CQDs) are valuable for their potential applications in optoelectronic devices. However, they are susceptible to thermal degradation during processing and while in use. Mitigating thermally induced sintering, which leads to absorption spectrum broadening and undesirable changes to thin film electrical properties, is necessary for the reliable design and manufacture of CQD-based optoelectronics. Here, low-temperature metal–oxide atomic layer deposition (ALD) was investigated as a method for mitigating sintering while preserving the optoelectronic properties of mercury telluride (HgTe) CQD films. ALD-coated films are subjected to temperatures up to 160 °C for up to 5 h and alumina (Al 2 O 3 ) is found to be most effective at preserving the optical properties, demonstrating the feasibility of metal–oxide in-filling to protect against sintering. HgTe CQD film electrical properties were investigated before and after alumina ALD in-filling, which was found to increase the p-type doping and hole mobility of the films. The magnitude of these effects depended on the conditions used to prepare the HgTe CQDs. With further investigation into the interaction effects of CQD and ALD process factors, these results may be used to guide the design of CQD–ALD materials for their practical integration into useful optoelectronic devices.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Infrared phase-change chiral metasurfaces with tunable circular dichroism

Integrating phase-change materials in metasurfaces has emerged as a powerful strategy to realize optical devices with tunable electromagnetic responses. Here, phase-change chiral metasurfaces based on GST-225 material with the designed trapezoid-shaped resonators are demonstrated to achieve tunable circular dichroism (CD) responses in the infrared regime. The asymmetric trapezoid-shaped resonators are designed to support two chiral plasmonic resonances with opposite CD responses for realizing switchable CD between negative and positive values using the GST phase change from amorphous to crystalline. The electromagnetic field distributions of the chiral plasmonic resonant modes are analyzed to understand the chiroptical responses of the metasurface. Furthermore, the variations in the absorption spectrum and CD value for the metasurface as a function of the baking time during the GST phase transition are analyzed to reveal the underlying thermal tuning process of the metasurface. The demonstrated phase-change metasurfaces with tunable CD responses hold significant promise in enabling many applications in the infrared regime such as chiral sensing, encrypted communication, and thermal imaging.

42 ENGINEERING↗
DOE OSTI2024

Redox Gating for Colossal Carrier Modulation and Unique Phase Control

Redox gating, a novel approach distinct from conventional electrolyte gating, combines reversible redox functionalities with common ionic electrolyte moieties to engineer charge transport, enabling power-efficient electronic phase control. This study achieves a colossal sheet carrier density modulation beyond 10 16 cm -2 , sustainable over thousands of cycles, all within the sub-volt regime for functional oxide thin films. The key advantage of this method lies in the controlled injection of a large quantity of carriers from the electrolyte into the channel material without the deleterious effects associated with traditional electrolyte gating processes such as the production of ionic defects or intercalated species. The redox gating approach offers a simple and practical means of decoupling electrical and structural phase transitions, enabling the isostructural metal-insulator transition and improved device endurance. The versatility of redox gating extends across multiple materials, irrespective of their crystallinity, crystallographic orientation, or carrier type (n- or p-type). This inclusivity encompasses functional heterostructures and low-dimensional quantum materials composed of sustainable elements, highlighting the broad applicability and potential of the technique in electronic devices.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Sequential infiltration of two-photon polymerized 3D photonic crystals for mid-IR spectroscopic applications

Photonic crystals (PhCs) are spatially organized structures with lattice parameters equivalent to the operational wavelength of light. PhCs have been subject to extensive research efforts in the last two decades and are known for controlling light propagation with applications in sensing and time-delayed communication due to the slow-light phenomenon. Despite their exceptional properties, PhCs are difficult to fabricate using planar micromachining techniques due to their periodic structures. Techniques like two-photon stereolithography have been discussed for PhC fabrication in the literature, but the inherent disadvantage of poor refractive index (RI) contrast results in limited application. In this work, we present sequential infiltration synthesis performed on two-photon stereolithographically printed 3D PhCs for infiltration with zinc oxide to increase the RI of 3D PhCs. Further, finite element analysis was performed over a range of RI contrast values to study the change in photonic bandgap (PBG) with RI contrast. The transmission spectra were recorded on 3D PhCs before and after infiltration to demonstrate the change experimentally. An increase in the PBG width and absorbance is seen postinfiltration due to enhanced RI. This work presents the first, to our knowledge, sequentially infiltrated enhanced 3D PhC fabricated with two-photon stereolithography.

3D printing↗
DOE OSTI2023

Epitaxial growth of oriented CoO films by radio-frequency sputtering deposition

Rock-salt CoO is a p-type semiconductor and its Neel temperature is close to room temperature. CoO-based compounds are known as promising systems for renewable energy harvest with high efficiency. CoO with catalytic and exchange bias properties can be widely used for industrial applications. In this paper, we report high-quality stable CoO(111) and (100) films epitaxially grown on c-cut (0001) and r-cut ($10\bar1$2) alpha-Al 2 O 3 substrates, respectively, using radio-frequency sputtering deposition. X-ray diffraction (XRD) measurements revealed that the CoO films had a rock-salt structure (Fm3m) with lattice constants of 4.2477 Å and 4.2617 Å for film grown on (0001) and ($10\bar1$2) α-Al 2 O 3 substrates, respectively. CoO films with the best crystal quality were grown at a substrate temperature of similar to ~700°C. XRD measurements of CoO(111) films indicated a lack of structural residual strain, whereas CoO(100) films had substantial amounts of structural strain. X-ray reflectivity (XRR) and transmission electron microscopy measurements showed neither oxygen vacancy nor defects in both CoO(111) and (100) films. Further, XRR revealed that the mean electron density of the CoO films was nearly identical to a pure CoO and that the films were considerably stable under the atmosphere.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Wavelength-tunable infrared chiral metasurfaces with phase-change materials

Optical phase-change materials exhibit tunable permittivity and switching properties during phase transition, which offers the possibility of dynamic control of optical devices. Here, a wavelength-tunable infrared chiral metasurface integrated with phase-change material GST-225 is demonstrated with the designed unit cell of parallelogram-shaped resonator. By varying the baking time at a temperature above the phase transition temperature of GST-225, the resonance wavelength of the chiral metasurface is tuned in the wavelength range of 2.33 µm to 2.58 µm, while the circular dichroism in absorption is maintained around 0.44. The chiroptical response of the designed metasurface is revealed by analyzing the electromagnetic field and displacement current distributions under left- and right-handed circularly polarized (LCP and RCP) light illumination. Moreover, the photothermal effect is simulated to investigate the large temperature difference in the chiral metasurface under LCP and RCP illumination, which allows for the possibility of circular polarization-controlled phase transition. The presented chiral metasurfaces with phase-change materials offer the potential to facilitate promising applications in the infrared regime, such as chiral thermal switching, infrared imaging, and tunable chiral photonics.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Operando study of mechanical integrity of high-volume expansion Li-ion battery anode materials coated by Al 2 O 3

Group IV elements and their oxides, such as Si, Ge, Sn and SiO have much higher theoretical capacity than commercial graphite anode. However, these materials undergo large volume change during cycling, resulting in severe structural degradation and capacity fading. Al 2 O 3 coating is considered an approach to improve the mechanical stability of high-capacity anode materials. To understand the effect of Al 2 O 3 coating directly, we monitored the morphology change of coated/uncoated Sn particles during cycling using operando focused ion beam–scanning electron microscopy. Here, the results indicate that the Al 2 O 3 coating provides local protection and reduces crack formation at the early stage of volume expansion. The 3 nm Al 2 O 3 coating layer provides better protection than the 10 and 30 nm coating layer. Nevertheless, the Al 2 O 3 coating is unable to prevent the pulverization at the later stage of cycling because of large volume expansion.

25 ENERGY STORAGE↗
DOE OSTI2022

Cesium intercalation of graphene: A 2D protective layer on alkali antimonide photocathode

Alkali antimonide photocathodes have wide applications in free-electron lasers and electron cooling. The short lifetime of alkali antimonide photocathodes necessitates frequent replacement of the photocathodes during a beam operation. Furthermore, exposure to mediocre vacuum causes loss of photocathode quantum efficiency due to the chemical reaction with residual gas molecules. Theoretical analyses have shown that covering an alkali antimonide photocathode with a monolayer graphene or hexagonal boron nitride protects it in a coarse vacuum environment due to the inhibition of chemical reactions with residual gas molecules. Alkali antimonide photocathodes require an ultra-high vacuum environment, and depositing a monolayer 2D material on it poses a serious challenge. In the present work, we have incorporated a novel method known as intercalation, in which alkali atoms pass through the defects of a graphene thin film to create a photocathode material underneath. Initially, Sb was deposited on a Si substrate, and a monolayer graphene was transferred on top of the Sb film. Heat cleaning around 550–600 °C effectively removed the Sb oxides, leaving metallic Sb underneath the graphene layer. Depositing Cs on top of a monolayer graphene enabled the intercalation process. Atomic force microscopy, Raman spectroscopy, x-ray photoelectron spectroscopy, low energy electron microscopy, and x-ray diffraction measurements were performed to evaluate photocathode formation underneath the monolayer graphene. Our analysis shows that Cs penetrated the graphene and reacted with Sb and formed Cs 3 Sb.

2D materials↗
DOE OSTI2022

Enhancing the metal–insulator transition in VO 2 heterostructures with graphene interlayers

In this work, studies were conducted on epitaxial VO 2 thin films to assess to the effect of remote epitaxy on the metal–insulator transition (MIT). The epitaxial VO 2 heterostructures were synthesized on both bare Al 2 O 3 (0001) substrates and Al 2 O 3 substrates coated with two monolayer-thick graphene. While both systems exhibit the MIT, the film grown by remote epitaxy on graphene demonstrates improved transport properties. Electrical transport measurements show that the on/off ratio is enhanced by a factor of ~7.5 and the switching temperature window is narrower for VO 2 thin films grown on graphene. By characterizing the heterostructures with a suite of structural, chemical, and spectroscopic tools, we find that the graphene interlayer inhibits oxygen vacancy diffusion from Al 2 O 3 (0001) during the VO 2 growth, resulting in improved electrical behavior at the MIT.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Controlled Formation of Conduction Channels in Memristive Devices Observed by X–ray Multimodal Imaging

Neuromorphic computing provides a means for achieving faster and more energy efficient computations than conventional digital computers for artificial intelligence (AI). However, its current accuracy is generally less than the dominant software-based AI. The key to improving accuracy is to reduce the intrinsic randomness of memristive devices, emulating synapses in the brain for neuromorphic computing. Here using a planar device as a model system, the controlled formation of conduction channels is achieved with high oxygen vacancy concentrations through the design of sharp protrusions in the electrode gap, as observed by X-ray multimodal imaging of both oxygen stoichiometry and crystallinity. Classical molecular dynamics simulations confirm that the controlled formation of conduction channels arises from confinement of the electric field, yielding a reproducible spatial distribution of oxygen vacancies across switching cycles. Furthermore, this work demonstrates an effective route to control the otherwise random electroforming process by electrode design, facilitating the development of more accurate memristive devices for neuromorphic computing.

36 MATERIALS SCIENCE↗
DOE OSTI2022

High-Throughput Microfluidics Platform for Intracellular Delivery and Sampling of Biomolecules from Live Cells

Nondestructive cell membrane permeabilization systems enable the intracellular delivery of exogenous biomolecules for cell engineering tasks as well as the temporal sampling of cytosolic contents from live cells for the analysis of dynamic processes. Here, in this paper, we report a microwell array format live-cell analysis device (LCAD) that can perform localized-electroporation induced membrane permeabilization, for cellular delivery or sampling, and directly interfaces with surface-based biosensors for analyzing the extracted contents. We demonstrate the capabilities of the LCAD via an automated high-throughput workflow for multimodal analysis of live-cell dynamics, consisting of quantitative measurements of enzyme activity using self-assembled monolayers for MALDI mass spectrometry (SAMDI) and deep-learning enhanced imaging and analysis. By combining a fabrication protocol that enables robust assembly and operation of multilayer devices with embedded gold electrodes and an automated imaging workflow, we successfully deliver functional molecules (plasmid and siRNA) into live cells at multiple time-points and track their effect on gene expression and cell morphology temporally. Furthermore, we report sampling performance enhancements, achieving saturation levels of protein tyrosine phosphatase activity measured from as few as 60 cells, and demonstrate control over the amount of sampled contents by optimization of electroporation parameters using a lumped model. Lastly, we investigate the implications of cell morphology on electroporation-induced sampling of fluorescent molecules using a deep-learning enhanced image analysis workflow.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2021

Selective volatile organic compound gas sensor based on carbon nanotubes functionalized with ZnO nanoparticles

Here this paper describes the theory and results for a new class of low-cost chemoresistive gas sensors designed for selective hydrocarbon gas detection. The sensors utilize a multiwalled carbon nanotube (MWCNT) backbone functionalized with metal oxide nanocrystals. Specifically, nanoparticles were grown on the surface of the MWCNTs using atomic layer deposition. The crystallinity of the ZnO-MWCNTs' heterostructure was examined by using a high-resolution transmission electron microscope. The structure of the ZnO/MWCNTs was analyzed using a scanning electron microscope and energy dispersive x ray. The Hall effect measurement shows p-type characteristics of the MWCNTs, supporting the typical PN junction formation with n-type ZnO nanocrystals. The electron-donating ability of ZnO provided a strong response to the ppm levels of toluene at room temperature (25 °C) and showed strong selectivity with other volatile organic compound gases such as benzene, methane, and formaldehyde.

47 OTHER INSTRUMENTATION↗
DOE OSTI2021

Electrolyte/Dye/TiO 2 Interfacial Structures of Dye-Sensitized Solar Cells Revealed by In Situ Neutron Reflectometry with Contrast Matching

The nature of an interfacial structure buried within a device assembly is often critical to its function. For example, the dye/TiO 2 interfacial structure that comprises the working electrode of a dye-sensitized solar cell (DSC) governs its photovoltaic output. These structures have been determined outside of the DSC device, using ex situ characterization methods; yet, they really should be probed while held within a DSC since they are modulated by the device environment. Dye/TiO 2 structures will be particularly influenced by a layer of electrolyte ions that lies above the dye self-assembly. We show that electrolyte/dye/TiO 2 interfacial structures can be resolved using in situ neutron reflectometry with contrast matching. Here, we find that electrolyte constituents ingress into the self-assembled monolayer of dye molecules that anchor onto TiO 2 . Some dye/TiO 2 anchoring configurations are modulated by the formation of electrolyte/dye intermolecular interactions. These electrolyte-influencing structural changes will affect dye-regeneration and electron-injection DSC operational processes. This underpins the importance of this in situ structural determination of electrolyte/dye/TiO 2 interfaces within representative DSC device environments.

14 SOLAR ENERGY↗
DOE OSTI2020

Approaching the Strain-Free Limit in Ultrathin Nanomechanical Resonators

Ultrathin mechanical structures are ideal building platforms to pursue the ultimate limit of nanomechanical resonators for applications in sensing, signal processing, and quantum physics. Unfortunately, as the thickness of the vibrating structures is reduced, the built-in strain of the structural materials plays an increased role in determining the mechanical performance of the devices. As a consequence, it is very challenging to fabricate resonators working in the modulus-dominant regime, where their dynamic behavior is exclusively determined by the device geometry. In this Letter, we report ultrathin doubly clamped nanomechanical resonators with aspect ratios as large as L/t similar to 5000 and working in the modulus-dominant regime. Here, we observed room temperature thermomechanically induced motion of multiple vibration modes with resonant frequencies closely matching the predicted values of Euler-Bernoulli beam theory under an axial strain of 6.3 x 10 -8 . The low strain of the devices enables a record frequency tuning ratio of more than 50 times. These results illustrate a new strategy for the quantitative design of nanomechanical resonators with unprecedented performance.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2020

Intrinsic Photoconductivity of few-layered ZrS 2 Phototransistors via Multiterminal Measurements

We report intrinsic photoconductivity studies on one of the least examined layered compounds, ZrS 2 .Few-atomic layer ZrS 2 field-effect transistors were fabricated on the Si/SiO 2 substrate and photoconductivity measurements were performed using both two- and four-terminal configurations under the illumination of 532 nm laser source. We measured photocurrent as a function of the incident optical power at several source-drain (bias) voltages. We observe a significantly large photoconductivity when measured in the multiterminal (four-terminal) configuration compared to that in the two-terminal configuration. For an incident optical power of 90 nW, the estimated photosensitivity and the external quantum efficiency (EQE) measured in two-terminal configuration are 0.5 A/W and 120%, respectively, under a bias voltage of 650 mV. Under the same conditions, the four-terminal measurements result in much higher values for both the photoresponsivity (R) and EQE to 6 A/W and 1400%, respectively. This significant improvement in photoresponsivity and EQE in the four-terminal configuration may have been influenced by the reduction of contact resistance at the metal-semiconductor interface, which greatly impacts the carrier mobility of low conducting materials. This suggests that photoconductivity measurements performed through the two-terminal configuration in previous studies on ZrS 2 and other 2D materials have severely underestimated the true intrinsic properties of transition metal dichalcogenides and their remarkable potential for optoelectronic applications.

36 MATERIALS SCIENCE↗