Search NASA⌕ Search

Engineering topics

Stanley, Andrew P. J.

Publications and source records attributed to Stanley, Andrew P. J..

Opportunities for green hydrogen production with land-based wind in the United States

Hydrogen (H 2 ) is an efficient energy carrier and storage mechanism that can supply both stationary and transport energy demand. Rapidly declining renewable energy generation costs; technology innovations in wind, solar, battery storage, and electrolysis; and a global push for more sustainable and secure energy have driven increased interest in green H 2 production. In this study, we develop an H 2 scenario analysis tool to assist in rapid, high-resolution insights into future, green H 2 pathways to achieve policy goals and market competitiveness. Using this tool, we estimate H 2 production and costs for U.S., off-grid scenarios given varying policy and cost scenarios from 2025–2035. Results indicate that achieving economically competitive green H 2 production (below $\$$2/kg) is possible in 2030 with no policy incentives (one site achieves this target), while increasing policy support to include wind and green H 2 production tax credits enables widespread economic viability sooner, with sub-$\$$2/kg LCOH targets achieved by 2025 and 51.7% of sites achieving this target by 2035. Maximizing policy support through prevailing wage and apprenticeship credit multipliers enable widespread economic viability, including sub-$\$$2/kg of green H 2 by 2025 and even negative pricing by 2035. Regions with lowest LCOH values correspond to high wind resource areas and capacity factors. Achieving decarbonization goals with green H 2 depends on technology cost reductions and policy support, with a maximum average LCOH reduction of $\$$23.10 between no and maximum policy support scenarios, and a maximum average LCOH reduction of $\$$25.86 between current, conservative technology costs and 2035 projected technology cost assumptions.

08 HYDROGEN↗

Enabling control co-design of the next generation of wind power plants

Abstract. Layout design and wake steering through wind plant control are important and complex components in the design and operation of modern wind power plants. They are currently optimized separately, but with more and more computational and experimental studies demonstrating the gains possible through wake steering, there is a growing need from industry and regulating bodies to combine the layout and control optimization in a co-design process. However, combining these two optimization problems is currently infeasible due to the excessive number of design variables and large solution space. In this article, we present a method that enables the coupled optimization of wind power plant layout and wake steering with no additional computational expense than a traditional layout optimization. We developed a geometric relationship between wind turbines to find an approximate optimal yaw angle, bypassing the need for either a nested or coupled wind plant control optimization. It also provides a significant and immediate improvement to wind power plant design by enabling the co-design of turbine layout and yaw control for wake steering. A small co-designed plant shown in this article produces 0.8 % more energy than its sequentially designed counterpart. This additional energy production comes with no additional infrastructure, turbine hardware, or control software; it is simply the outcome of optimizing the turbine layout and yaw control together, resulting in millions of dollars of additional revenue for the wind power plants of the future.

17 WIND ENERGY↗

A comparison of eight optimization methods applied to a wind farm layout optimization problem

Abstract. Selecting a wind farm layout optimization method is difficult. Comparisons between optimization methods in different papers can be uncertain due to the difficulty of exactly reproducing the objective function. Comparisons by just a few authors in one paper can be uncertain if the authors do not have experience using each algorithm. In this work we provide an algorithm comparison for a wind farm layout optimization case study between eight optimization methods applied, or directed, by researchers who developed those algorithms or who had other experience using them. We provided the objective function to each researcher to avoid ambiguity about relative performance due to a difference in objective function. While these comparisons are not perfect, we try to treat each algorithm more fairly by having researchers with experience using each algorithm apply each algorithm and by having a common objective function provided for analysis. The case study is from the International Energy Association (IEA) Wind Task 37, based on the Borssele III and IV wind farms with 81 turbines. Of particular interest in this case study is the presence of disconnected boundary regions and concave boundary features. The optimization methods studied represent a wide range of approaches, including gradient-free, gradient-based, and hybrid methods; discrete and continuous problem formulations; single-run and multi-start approaches; and mathematical and heuristic algorithms. We provide descriptions and references (where applicable) for each optimization method, as well as lists of pros and cons, to help readers determine an appropriate method for their use case. All the optimization methods perform similarly, with optimized wake loss values between 15.48 % and 15.70 % as compared to 17.28 % for the unoptimized provided layout. Each of the layouts found were different, but all layouts exhibited similar characteristics. Strong similarities across all the layouts include tightly packing wind turbines along the outer borders, loosely spacing turbines in the internal regions, and allocating similar numbers of turbines to each discrete boundary region. The best layout by annual energy production (AEP) was found using a new sequential allocation method, discrete exploration-based optimization (DEBO). Based on the results in this study, it appears that using an optimization algorithm can significantly improve wind farm performance, but there are many optimization methods that can perform well on the wind farm layout optimization problem, given that they are applied correctly.

17 WIND ENERGY↗

Optimal Wind Turbine Design for H2 Production

NREL and industrial partners GE and Nel seek to advance affordable green hydrogen production by optimizing wind turbine design specifically for hydrogen production and validating designs using NREL's ARIES facilities. This project will couple wind turbine, wind plant, solar plant, and electrolyzer models to predict hydrogen production from variable, renewable power sources. It will then use gradient-based optimization with exact-analytic gradients to optimize wind turbine rotor diameter, hub height, and power rating for optimal hydrogen production. Finally, it will validate the optimal turbine designs using the ARIES research platform, where it will compare a baseline turbine to the optimal design for a variety of scenarios and resources.

electrolyzer↗

Serial-Refine Method for Fast Wake-Steering Yaw Optimization

In this paper we present the Serial-Refine method for quickly finding the optimal yaw angles in wake steering. The method optimizes turbine angles serially from upstream to downstream using a small number of candidate angles. The presented results show that Serial-Refine finds solutions that are at least as good as former conventional optimization approaches but that require much less computation time.

17 WIND ENERGY↗

Optimizing the physical design and layout of a resilient wind, solar, and storage hybrid power plant

We report as wind and solar technologies improve and their costs decrease, the share of power produced by these sources will increase. As the market penetration increases, these power sources will need to provide grid services, such as dispatchability, in addition to providing energy. One way to reduce variability, provide higher quality power to the grid, and address local grid stability issues is through colocating wind and solar power plants. In addition to operating reliably during normal operating conditions, in scenarios with high penetrations of renewable generation, it is important that these hybrid plants can withstand production disruptions and continue to supply power despite prolonged resource reduction, extreme weather events, or other disruptions. In this paper, we present a methodology to optimize a wind-solar-battery hybrid power plant down to the component level that is resilient against production disruptions and that can continually produce some minimum required power. We introduce the models and assumptions we used to simulate a hybrid power plant as well as the design variable parameterization and specific methods we used to optimize the plant. We demonstrate the performance of our method by comparing a plant optimized for different objectives, generation outage durations, minimum power requirements, and power purchase agreements. Although the plant design is sensitive to model parameters and various other assumptions, our results demonstrate some of the optimal designs that occur in different scenarios and what one should expect when designing a hybrid wind-solar-storage power plant.

14 SOLAR ENERGY↗

Wind Farm Layout Optimization with Loads Considerations

The objective of this paper is to improve the annual energy production of a wind farm by optimizing the layout of a wind farm, while considering fatigue loads on turbines. In this paper, the loads are estimated using the edgewise bending moment computed using CCBlade, a steady-state blade element momentum code. The edgewise bending moment is then used to calculate fatigue damage using Miner's rule. The fatigue damage is used to constrain the layout optimization problem. We show that our method can predict blade root damage with similar trends to damage calculated with other methods, such as a complex, computationally expensive large-eddy simulation and unsteady aeroelastic code. We also optimize wind farm layouts and show that, for a simple problem with two wind directions and ten turbines, the fatigue damage can be constrained without sacrificing wind farm power production.

17 WIND ENERGY↗

Coupled wind turbine design and layout optimization with nonhomogeneous wind turbines

Abstract. In this study, wind farms were optimized to show the benefit of coupling complete turbine design and layout optimization as well as including two different turbine designs in a fixed 1-to-1 ratio in a single wind farm. For our purposes, the variables in each turbine optimization include hub height, rotor diameter, rated power, tower diameter, tower shell thickness, and implicit blade chord-and-twist distributions. A 32-turbine wind farm and a 60-turbine wind farm were both considered, as well as a variety of turbine spacings and wind shear exponents. Structural constraints as well as turbine costs were considered in the optimization. Results indicate that coupled turbine design and layout optimization is superior to sequentially optimizing turbine design, then turbine layout. Coupled optimization results in an additional 2 %–5 % reduction in the cost of energy compared to optimizing sequentially for wind farms with turbine spacings of 8.5–11 rotor diameters. Smaller wind farms benefit even more from coupled optimization. Furthermore, wind farms with closely spaced wind turbines can greatly benefit from nonuniform turbine design throughout the farm. Some of these wind farms with heterogeneous turbine design have an additional 10 % cost-of-energy reduction compared to wind farms with identical turbines throughout the farm.

Stanley, Andrew P. J.↗

Optimization of turbine design in wind farms with multiple hub heights, using exact analytic gradients and structural constraints

Wind farms are generally designed with turbines of all the same hub height. If wind farms were designed with turbines of different hub heights, wake interference between turbines could be reduced, lowering the cost of energy (COE). This paper demonstrates a method to optimize onshore wind farms with two different hub heights using exact, analytic gradients. Gradient-based optimization with exact gradients scales well with large problems and is preferable in this application over gradient-free methods. Our model consisted of the following: a version of the FLOw Redirection and Induction in Steady-State wake model that accommodated three-dimensional wakes and calculated annual energy production, a wind farm cost model, and a tower structural model, which provided constraints during optimization. Structural constraints were important to keep tower heights realistic and account for additional mass required from taller towers and higher wind speeds. We optimized several wind farms with tower height, diameter, and shell thickness as coupled design variables. Our results indicate that wind farms with small rotors, low wind shear, and closely spaced turbines can benefit from having two different hub heights. A nine-by-nine grid wind farm with 70-meter rotor diameters and a wind shear exponent of 0.08 realized a 4.9% reduction in COE by using two different tower sizes. If the turbine spacing was reduced to 3 diameters, the reduction in COE decreased further to 11.2%. Allowing for more than two different turbine heights is only slightly more beneficial than two heights and is likely not worth the added complexity.

17 WIND ENERGY↗

Best Practices for Wake Model and Optimization Algorithm Selection in Wind Farm Layout Optimization

This paper presents the results of two case studies regarding the wind farm layout optimization problem. We asked a general audience to take part in the studies that we designed, and nine individuals participated. Case study 1 considered variations in optimization strategies for a given simple Gaussian wake model. Participants were provided with a wake model that outputs annual energy production (AEP) for an input set of wind turbine locations. Participants used an optimization method of their choosing to find an optimal wind farm layout. Case study 2 looked at trade-offs in performance resulting from variation in both physics model and optimization strategy. For case study 2, participants calculated AEP using a wake model of their choice while also implementing their chosen optimization method. Participants then used their wake model to calculate the AEP all other participant submitted turbine configurations produce for cross-comparison results. for optimized turbine locations were then cross-compared by recalculating the AEP using every other participant's wake model. Results for case study 1 show that the best optimal wind farm layouts in this study were achieved by participants who used gradient-based optimization methods. A front-runner emerged with the Sparse Nonlinear OPTimizer plus Wake Expansion Continuation (SNOPTplusWEC) optimization method, which consistently discovered a higher AEP for each scenario. Results for case study 2 show that for small wind farms with few turbines, turbine placement on the wind farm boundary is superior. Conclusions for case study 2 were drawn from participant cross-comparison of results.

17 WIND ENERGY↗

Benefits of Two Turbine Rotor Diameters and Hub Heights in the Same Wind Farm

Significant turbine-wake interactions greatly reduce power output in a wind farm. If different turbine hub heights and rotor diameters are included in the same wind farm, the wake interference in the farm will be reduced, resulting in a lower cost of energy (COE) than a farm with identical turbines. In this paper, we present a method to model wind farm COE in farms with hub heights and rotor diameters that vary across the wind farm. We also demonstrate how to optimize these wind farms to minimize COE. The results show that COE can be greatly reduced in wind farms with non-homogeneous turbines, especially when the turbines are spaced close together. For a unidirectional wind rose, including different turbine design in the wind farm has a similar decrease in COE to spreading the wind turbines farther apart. When the rotor diameter and hub height of the wind turbines in a farm are optimized uniformly, a COE decrease of 4% to 13% (depending on the grid spacing and wind shear exponent) is achieved compared to the baseline. When the rotor diameter and turbine heights are optimized non-uniformly, with two different diameters and heights throughout the farm, there is a COE decrease of 22% to 41% compared to the baseline. For a more spread wind rose with a dominant probability from the west, there is a COE decrease between 3% and 10% for uniformly optimized rotor diameter and height compared to the baseline. With two optimized rotor diameters and heights through the farm, a COE decrease of 3% to 19% is achieved. For a similar wind rose shifted such that the dominant wind direction is from the northwest, a COE decrease between 3% and 10% results from uniformly optimized wind turbines compared to the baseline. A COE decrease of 3% to 17% compared to the baseline occurs with two different turbines are optimized throughout the wind farm.

17 WIND ENERGY↗

Gradient-Based Optimization of Wind Farms with Different Turbine Heights: Preprint

Turbine wakes reduce power production in a wind farm. Current wind farms are generally built with turbines that are all the same height, but if wind farms included turbines with different tower heights, the cost of energy (COE) may be reduced. We used gradient-based optimization to demonstrate a method to optimize wind farms with varied hub heights. Our study includes a modified version of the FLORIS wake model that accommodates three-dimensional wakes integrated with a tower structural model. Our purpose was to design a process to minimize the COE of a wind farm through layout optimization and varying turbine hub heights. Results indicate that when a farm is optimized for layout and height with two separate height groups, COE can be lowered by as much as 5%-9%, compared to a similar layout and height optimization where all the towers are the same. The COE has the best improvement in farms with high turbine density and a low wind shear exponent.

17 WIND ENERGY↗