Search NASA⌕ Search

Engineering topics

Starnes, J. H., Jr.

Publications and source records attributed to Starnes, J. H., Jr..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2000

Structural Similitude and Scaling Laws for Plates and Shells: A Review

This paper deals with the development and use of scaled-down models in order to predict the structural behavior of large prototypes. The concept is fully described and examples are presented which demonstrate its applicability to beam-plates, plates and cylindrical shells of laminated construction. The concept is based on the use of field equations, which govern the response behavior of both the small model as well as the large prototype. The conditions under which the experimental data of a small model can be used to predict the behavior of a large prototype are called scaling laws or similarity conditions and the term that best describes the process is structural similitude. Moreover, since the term scaling is used to describe the effect of size on strength characteristics of materials, a discussion is included which should clarify the difference between "scaling law" and "size effect". Finally, a historical review of all published work in the broad area of structural similitude is presented for completeness.

Simitses, G. J.↗
NASA NTRS2000

Residual Strength Analysis Methodology: Laboratory Coupons to Structural Components

The NASA Aircraft Structural Integrity (NASIP) and Airframe Airworthiness Assurance/Aging Aircraft (AAA/AA) Programs have developed a residual strength prediction methodology for aircraft fuselage structures. This methodology has been experimentally verified for structures ranging from laboratory coupons up to full-scale structural components. The methodology uses the critical crack tip opening angle (CTOA) fracture criterion to characterize the fracture behavior and a material and a geometric nonlinear finite element shell analysis code to perform the structural analyses. The present paper presents the results of a study to evaluate the fracture behavior of 2024-T3 aluminum alloys with thickness of 0.04 inches to 0.09 inches. The critical CTOA and the corresponding plane strain core height necessary to simulate through-the-thickness effects at the crack tip in an otherwise plane stress analysis, were determined from small laboratory specimens. Using these parameters, the CTOA fracture criterion was used to predict the behavior of middle crack tension specimens that were up to 40 inches wide, flat panels with riveted stiffeners and multiple-site damage cracks, 18-inch diameter pressurized cylinders, and full scale curved stiffened panels subjected to internal pressure and mechanical loads.

Dawicke, D. S.↗
NASA NTRS1998

Buckling mode localization in elastic plates due to misplacement in the stiffener location

This paper deals with the buckling of the stiffened plate under uni-axial compression. The direct integration of the governing differential equation is performed and the exact solution to the problem is obtained. As examples, a square plate with single stiffener, and a stiffened three-span, continuous plate are investigated, with special attention given to the influence of stiffener misplacement on the buckling load and mode shape of the plate. It is found that a small misplacement of the stiffeners from the nominal configuration may change the buckling mode from a global one to a highly localized one.

Elishakoff, I.↗
NASA NTRS1998

Buckling mode localization in a multi-span periodic structure with a disorder in a single span

This paper investigates the buckling mode localization in the periodic multi-span beam with disorder occurring in an arbitrary single span. The analytical finite difference calculus is used in conjunction with the conventional displacement method to derive the transcendental equations from which buckling load is calculated. The underlying treatment is general and the solution thus obtained is exact. Numerical results show that the buckling mode is highly localized in the vicinity of the disordered span of the beam.

Li, Y. W.↗
NASA NTRS1998

Prediction of Natural Frequency and Buckling Load Variability due to Uncertainty in Material Properties by Convex Modeling

Composite materials are widely used in various types of engineering structures. To a large extent, the properties of composite materials are dependent on the fabrication process. But even the composite materials manufactured by the same process may demonstrate differences in their elastic properties. For design purposes, one should be aware of the potential variations in load-carrying capacity and dynamic behavior of such structures that can arise due to the uncertainty in elastic moduli. A more realistic analysis of composite structures should be performed with the variations of the elastic moduli being taken into consideration at the same time. The present paper is a generalization of a study where the influence of uncertainty in elastic moduli on the axial buckling load was discussed. Here, we consider another case of buckling, shells under uniform external pressure. In addition, this paper deals with the variability of natural frequencies by use of convex modeling, which is apparently the first study of this kind in the literature. A numerical approach to the uncertainty problem is nonlinear programming, which we apply to solve the same problem to generate a set of comparable numerical data. The results from both methods show good agreement throughout. Thus, the effectiveness of the analytic convex modeling is clearly demonstrated. The bounds of he natural frequency and the buckling load provide the designer with a better view of the vibrational behavior and the actual load carrying capacities possessed by the composite structure.

Li, Y. W.↗
NASA NTRS1998

Derivation of multi-dimensional ellipsoidal convex model for experimental data

This paper deals with determination of the best ellipsoidal model fitting the available limited experimental data. The problem is defined as that of finding the minimum volume ellipsoid containing all experimental data. A general transformation matrix for the rotation of N-dimensional coordinate system is first obtained by the Gramm-Schmidt orthogonalization procedure. The use of this matrix makes it possible to search in all possible directions to find an ellipsoid with a minimum volume. The general procedure is illustrated by examples in which the real data is utilized. An invariance property of the response with uncertain parameters of different physical nature is also discussed.

Zhu, L. P.↗
NASA NTRS1998

Passive control of buckling deformation via Anderson Localization Phenomenon

Buckling problems of two types of multi-span elastic plates with transverse stiffeners are considered using a method based on the finite difference calculus. The discreteness of the stiffeners is accounted for. It is found that the torsional rigidity of the stiffener plays an important role in the buckling mode pattern. When the torsional rigidity is properly adjusted, the stiffener can act as an isolator of deformation for the structure at buckling so that the deflection is only limited to a small area.

Elishakoff, Isaac↗
NASA NTRS1993

Numerical and experimental investigation of the bending response of thin-walled composite cylinders

A numerical and experimental investigation of the bending behavior of six eight-ply graphite-epoxy circular cylinders is presented. Bending is induced by applying a known end-rotation to each end of the cylinders, analogous to a beam in bending. The cylinders have a nominal radius of 6 inches, a length-to-radius ratio of 2 and 5, and a radius-to-thickness ratio of approximately 160. A (+/- 45/0/90)S quasi-isotropic layup and two orthotropic layups, (+/- 45/0 sub 2)S and (+/- 45/90 sub 2)S, are studied. A geometrically nonlinear special-purpose analysis, based on Donnell's nonlinear shell equations, is developed to study the prebuckling responses and gain insight into the effects of non-ideal boundary conditions and initial geometric imperfections. A geometrically nonlinear finite element analysis is utilized to compare with the prebuckling solutions of the special-purpose analysis and to study the buckling and post buckling responses of both geometrically perfect and imperfect cylinders. The imperfect cylinder geometries are represented by an analytical approximation of the measured shape imperfections. Extensive experimental data are obtained from quasi-static tests of the cylinders using a test fixture specifically designed for the present investigation. A description of the test fixture is included. The experimental data are compared to predictions for both perfect and imperfect cylinder geometries. Prebuckling results are presented in the form of displacement and strain profiles. Buckling end-rotations, moments, and strains are reported, and predicted mode shapes are presented. Observed and predicted moment vs. end-rotation relations, deflection patterns, and strain profiles are illustrated for the post buckling responses. It is found that a geometrically nonlinear boundary layer behavior characterizes the prebuckling responses. The boundary layer behavior is sensitive to laminate orthotropy, cylinder geometry, initial geometric imperfections, applied end-rotation, and non-ideal boundary conditions. Buckling end-rotations, strains, and moments are influenced by laminate orthotropy and initial geometric imperfections. Measured buckling results correlate well with predictions for the geometrically imperfect specimens. The postbuckling analyses predict equilibrium paths with a number of scallop-shaped branches that correspond to unique deflection patterns. The observed postbuckling deflection patterns and measured strain profiles show striking similarities to the predictions in some cases. Ultimate failure of the cylinders is attributed to an interlaminar shear failure mode along the nodal lines of the postbuckling deflection patterns.

Fuchs, J. P.↗
NASA NTRS1993

Postbuckling of laminated flat and curved panels under combined thermal and mechanical loadings

The static postbuckling of simply-supported, symmetrically laminated composite and single-layered flat and doubly-curved shallow panels, subjected to both a stationary non-uniform temperature field and a system of mechanical loadings is investigated. A number of non-classical effects related to the transverse shear flexibility of constituent materials, the unavoidable initial geometric imperfections and the character of tangential boundary conditions are considered and pertinent conclusions about their role on the postbuckling response are emphasized. Throughout the paper the results based upon a higher-order theory are compared with their first order shear deformable and classical counterparts, and conclusions related to their range of applicability are outlined.

Librescu, L.↗
NASA NTRS1992

Buckling of stiffened shells with random initial imperfections, thickness and boundary conditions

The paper proposes a method to predict the buckling load of stiffened, composite shells reliably, where besides the randomness of the initial geometric imperfections also a random variation of the wall thickness and the uncertainty of the precise edge conditions is included in the analysis. The introduction of the variability in the thickness from shell to shell, in an ensemble of nominally identical shells, produced by the same manufacturing procedure is motivated by the growing realization of the importance of thickness variations by composite shells. The probabilistic treatment of the boundary conditions is dictated by the fact that 'true', deterministically specified boundary conditions are unlikely to be realizable in practice.

Elishakoff, I.↗
NASA NTRS1991

Design of a blade-stiffened composite panel with a hole

A procedure is developed analytically to design and produce an optimized stiffened panel with a centrally located hole. The PASCO panel-buckling analysis and sizing code is employed with the Engineering Analysis Language (EAL) code for finite-element analysis to optimize the design variables. Important design considerations are stiffener height and ply thicknesses in the skin and the stiffener laminates. The EAL code calculates the maximum strains around the hole boundary, and the resulting constraints are combined with the buckling constraint developed by the PASCO code. Cooptimization of the two codes is effected until convergence on the optimal solution is achieved. Results of the analytical procedure are experimentally verified by applying a compressive end-load to graphite-fiber laminated plates with center holes. The experimental results support the analytical procedure, and it is found that for the same weight, the soft-skin designs tested are found to have the best tolerance characteristics and resistance to failure.

Nagendra, S.↗
NASA NTRS1986

Postbuckling behavior of selected graphite-epoxy cylindrical panels loaded in axial compression

Results of an experimental and analytical study of the postbuckling behavior of selected graphite-epoxy cylindrical panels loaded in axial compression are presented. The postbuckling response and failure characteristics of the panels are described. The postbuckling response of each specimen is typical of axially-compressed cylindrical shells and curved panels in that a severe reduction in load occurs at buckling. Failure of all panels initiated near regions with severe local bending gradients. Analytical results from a nonlinear general shell finite element analysis computer code correlate well with typical experimental results up to buckling. Measured initial geometric imperfections were included in the postbuckling analysis. Analytically-determined stress distributions in the postbuckling response were used with failure criteria to identify the load level and the location of first-ply failure.

Knight, N. F., Jr.↗
NASA NTRS1986

Stiffener-skin interactions in pressure-loaded composite panels

The effects of flange thickness, web height, and skin stiffness on the strain distributions in the skin-stiffener interface region of pressure-loaded graphite-epoxy panels, stiffened by the type-T stiffener, were examined at pressure levels up to one atmosphere. The results indicate that at these pressures geometric nonlinearities are important, and that the overall stiffener stiffness has a significant effect on panel response, particularly on the out-of-plane deformation or pillowing of the skin. The strain gradients indicated that the interface between the skin and the stiffener experiences two components of shear stress, in addition to a normal (peel) stress. Thus, the skin-stiffener interface problem is a three-dimensional problem rather than a two-dimensional one, as is often assumed.

Loup, D. C.↗
NASA NTRS1985

Use of optimum stiffness tailoring to improve the compressive strength of composite plates with holes

A structural optimization procedure is used to tailor the cross-sectional stiffness distribution of compression-loaded composite plates with holes. Minimum mass designs are obtained for plates with cross sections consisting of two different balanced symmetric laminates with 0 deg, + or - 45 deg and 90 deg plies. The plate interior region contains the hole and is designed from a softer material system with a higher failure strain than the plate exterior region. All-graphite-epoxy plates and hybrid graphite/glass-epoxy plates were studied. Other designs with different percentages of 0 deg and + or 45 deg plies in the exterior laminate are compared with the optimum designs. Designs with uniform cross-sectional stiffnesses also are compared with the tailored cross-sectional stiffness designs. Specimens of each design were tested to verify the analytical predictions. The results show that cross-sectional stiffness tailoring can increase the compressive strength and decrease the mass of compression-loaded laminated plates with holes.

Haftka, R. T.↗
NASA NTRS1985

Postbuckling behavior of selected curved stiffened graphite-epoxy panels loaded in axial compression

Results of an experimental and analytical study of the postbuckling behavior of selected curved stiffened graphite-epoxy panels loaded in axial compression are presented. The postbuckling response and failure characteristics of the panels are described. Each panel had four equally-spaced I-shaped stiffeners and 16-ply quasi-isotropic skins. Panels with three different stiffener spacings were tested. Failure of all panels initiated in a skin-stiffener interface region. Analytical results from a nonlinear general shell finite element analysis computer code correlate well with typical postbuckling test results up to failure. The analytical modeling detail necessary to predict accurately the response of the panel is described. Measured initial geometric imperfections were included in the postbuckling analysis.

Knight, N. F., Jr.↗