Search NASA⌕ Search

Engineering topics

Steckel, Janice A.

Publications and source records attributed to Steckel, Janice A..

At least 19 records

Integrating crystallographic and computational approaches to carbon-capture materials for the mitigation of climate change

Here, this article presents an overview of the current state of the art in the structure determination of microporous carbon-capture materials, as discussed at the recent NIST workshop “Integrating Crystallographic and Computational Approaches to Carbon-Capture Materials for the Mitigation of Climate Change”. The continual rise in anthropogenic CO 2 concentration and its effect on climate change call for the implementation of carbon capture technologies to reduce the CO 2 concentration in the atmosphere. Porous solids, including metal–organic frameworks (MOFs), are feasible candidates for gas capture and storage applications. However, determining the structure of these materials represents a significant obstacle in their development into advanced sorbents. The existing difficulties can be overcome by integrating crystallographic methods and theoretical modeling. The workshop gathered experimentalists and theorists from academia, government, and industry to review this field and identify approaches, including collaborative opportunities, required to develop tools for rapid determination of the structures of porous solid sorbents and the effect of structure on the carbon capture performance. We highlight the findings of that workshop, especially in the need for reference materials, standardized procedures and reporting of sorbent activation and adsorption measurements, standardized reporting of theoretical calculations, and round-robin structure determination.

36 MATERIALS SCIENCE↗

Creation of Polymer Datasets with Targeted Backbones for Screening of High-Performance Membranes for Gas Separation

A simple approach was developed to computationally construct a polymer dataset by combining simplified molecular-input line-entry system (SMILES) strings of a targeted polymer backbone and a variety of molecular fragments. This method was used to create 14 polymer datasets by combining seven polymer backbones and molecules from two large molecular datasets (MOSES and QM9). Polymer backbones that were studied include four polydimethylsiloxane (PDMS) based backbones, poly(ethylene oxide) (PEO), poly(allyl glycidyl ether) (PAGE), and polyphosphazene (PPZ). The generated polymer datasets can be used for various cheminformatics tasks, including high-throughput screening for gas permeability and selectivity. This study utilized machine learning (ML) models to screen the polymers for CO2/CH4 and CO2/N2 gas separation using membranes. Several polymers of interest were identified. Here the results highlight that employing an ML model fitted to polymer selectivities leads to higher accuracy in predicting polymer selectivity compared to using the ratio of predicted permeabilities.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effect of Flexibility in Molecular Simulations of Carbon Dioxide Adsorption and Diffusion in a Cuprous Triazolate Framework

Using fixed atom force fields to model gas adsorption in flexible metal organic frameworks (MOFs) is known to pose difficulties in accurately reproducing and predicting experimental results. This paper studies the difference in accuracy between flexible and fixed atom force fields in reproducing CO 2 adsorption measurements in MAF-2 ([Cu(etz)]∞ (MAF-2, Hetz) 3,5-diethyl-1,2,4-triazole), an NbO-type triazolate scaffold with a bcu cavity system and attached ethyl groups. The flexible force field used to run the hybrid molecular dynamics and grand canonical Monte Carlo calculations were generated using the QuickFF software incorporating van der Waals parameters from the Universal Force Field (UFF) and density derived electrostatic and chemical (DDEC) charges. The fixed atom force field used was composed of UFF van der Waals parameters together with DDEC charges. The calculations were run at 298 K and at pressures of 0.1, 0.3, 0.5, 0.8, and 1 bar. It was observed that for this MOF the rigid force field overpredicted gas adsorption, whereas the flexible force field values closely matched experimental data. In the flexible structure, the freely moving ethyl groups of MAF-2 hindered adsorption, reducing the interaction energy between CO 2 and the N atoms of the triazolate framework as well as reducing the size of the largest cavity diameter. Here, the combination of these factors led to improved prediction of adsorption values with the flexible forcefield as compared to the rigid forcefield, demonstrating the need for modeling MOFs in a way more indicative of their behavior.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Strong degradation of polycarbonate and polystyrene by the CO 2 capture solvent diethyl sebacate

Here, we report on observations of strong degradation of a polycarbonate vessel by a solvent being considered for a CO 2 capture process, diethyl sebacate. This degradation led to failure of a polymeric hollow fiber membrane unit. Additional tests showed rapid degradation of polycarbonate safety glasses and polystyrene-based petri dishes by exposure to diethyl sebacate at ambient conditions. We also report on safe operations with diethyl sebacate in extensive experiments studying the corrosion of steel in CO 2 -pressurized reactors lined with PTFE and using PTFE gaskets. Used diethyl sebacate was also stored for long time periods in bottles made from low-density polyethylene bottles without physical deterioration. These observations indicate that care must be taken in development of new contactors and processes for CO 2 capture with diethyl sebacate and related solvents and in the choice of material for storage.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Single polymer sorbent fibers for high performance and rapid direct air capture

Polymers of intrinsic microporosity (PIM) fibers featuring amidoxime and amine functionalities were formulated into high-performance CO 2 adsorbents. Fiber sorbents were composed of a single porous polymer component functionalized with molecular amines to increase the CO 2 capture uptake and kinetics. Here we report the highest CO 2 uptake capacity (3.3 wt% (0.8 mmol g –1 ) CO 2 at 400 ppm) among all PIM-based and single polymeric sorbents to date. Moreover, the sorbents exhibited rapid CO 2 adsorption rates (capturing 90% of its total capacity within 7 min.) and cost efficient and reproducible regeneration (at 70 °C) which are essential for reducing the cost of direct air capture.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Designing optimal core–shell MOFs for direct air capture

Metal–organic frameworks (MOFs), along with other novel adsorbents, are frequently proposed as candidate materials to selectively adsorb CO 2 for carbon capture processes. However, adsorbents designed to strongly bind CO 2 nearly always bind H 2 O strongly (sometimes even more so). Given that water is present in significant quantities in the inlet streams of most carbon capture processes, a method that avoids H 2 O competition for the CO 2 binding sites would be technologically valuable. Here, in this paper, we consider a novel core–shell MOF design strategy, where a high-CO 2 -capacity MOF “core” is protected from competitive H 2 O-binding via a MOF “shell” that has very slow water diffusion. We consider a high-frequency adsorption/desorption cycle that regenerates the adsorbents before water can pass through the shell and enter the core. To identify optimal core–shell MOF pairs, we use a combination of experimental measurements, computational modeling, and multiphysics modeling. Our library of MOFs is created from two starting MOFs-UiO-66 and UiO-67-augmented with 30 possible functional group variations, yielding 1740 possible core–shell MOF pairs. After defining a performance score to rank these pairs, we identified 10 core–shell MOF candidates that significantly outperform any of the MOFs functioning alone.

42 ENGINEERING↗

Molecular design and fabrication of PIM-1/polyphosphazene blend membranes with high performance for CO 2 /N 2 separation

New polymeric blend membranes for CO 2 separation were synthesized based on insights from molecular dynamics simulation. A molecular-level structure-property relationship in polymers of intrinsic microporosity (PIM) based blend membranes, was investigated in detail computationally. Calculated local density profiles and energy of interaction of the blend membranes, composed of PIM-1 and various polyphosphazenes, showed that using the polyphosphazene with a higher concentration of ether side chains can improve the compatibility with PIM-1. Furthermore, based on the findings of computational studies, blend membranes were experimentally fabricated from PIM-1 and polyphosphazenes with various polyether side chain concentrations. Polyether concentration in polyphosphazenes was correlated with the film properties and gas transport performance of the blend membranes. Blend membranes showed very high CO 2 permeability (3100-5300 barrer) and improved CO 2 /N 2 selectivity (24-28), outperforming all other PIM-based blend membranes reported to date. Moreover, the CO 2 permeability performance of the blend membranes was tested 566 hours under real post-combustion flue gas from a coal-fired power plant, including CO 2 , N 2 , H 2 O, O 2 , SO x and NO x .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Enhanced Guest@MOF Interaction via Stepwise Thermal Annealing: TCNQ@Cu 3 (BTC) 2

Confinement of guest molecules in porous materials such as metal organic frameworks (MOFs) promises to deliver emergent properties separate from those of the individual components. Understanding the confinement mechanism is therefore important for the development of new synthesis routes that adjust MOF properties for specific applications. In this work, we developed a new synthetic method to confine guest molecules into MOF pores through a stepwise thermal annealing process, wherein the confinement of 7,7,8,8-tetracyanoquinodimethane (TCNQ) guest molecules into Cu 3 (BTC) 2 (BTC = benzene-1,3,5-tricarboxylic acid) MOF host is used as an example of how novel materials can be created with new physical properties. The stepwise thermal annealing process includes 1) an activation process of pristine Cu 3 (BTC) 2 MOF to maximizes the TCNQ guest loading in the MOF host by effectively removing the residual solvents and 2) post-annealing of the TCNQ infiltrated MOF to enhances the interaction of the confined guest molecules with the MOF host. Obtained experimental results based on thermogravimetric analysis, N 2 gas adsorption, electron microscopy, X-ray diffraction and infrared absorption, combined with density functional theory calculations provide evidence that the use of a stepwise thermal annealing process yields enhancements in the guest loading, packing and interaction between the TCNQ guest and the MOF host. The new hybrid TCNQ@Cu 3 (BTC) 2 system is stable and shows no significant signs of structural degradation even after submersion in water. This is due to the presence of significantly stronger interactions of TCNQ with the frame-work metal ions compared to those of the water molecules competing for the same framework binding sites. It was also found that TCNQ@Cu 3 (BTC) 2 system maintains a significant CO 2 and CH 4 adsorption potential compared to the pristine MOF. The synthetic route developed in this work yields novel guest@MOF hybrid systems that will be useful for many MOF-based applications such as gas separations and chemical sensors performed under humid conditions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Levelized Cost of CO 2 Captured Using Five Physical Solvents in Pre-combustion Applications

Aspen Plus v8.8 was used to perform techno-economic analysis (TEA) of a CO 2 capture process from a typical fuel gas stream in a 543-MW pre-combustion power plant using five different physical solvents (Selexol, PEGPDMS-1, NMP, [aPy][Tf 2 N] and [hmim][Tf 2 N]). The process included a countercurrent packed-bed absorber operating under high-pressure over a wide range of temperatures and three pressure-swing flash drums for solvent regeneration. Furthermore, two packings, Mellapak 250Y and IMTP50, were used and the Levelized costs of CO 2 captured (LCOC) were calculated. The simulation results indicated that using Mellapak 250Y exhibited lower LCOC values than those when using IMTP50 for the five solvents under all conditions used as it offered better mass transfer. The CO 2 capture process carried out at low temperatures showed lower LCOC values than those at higher temperatures due to the increased CO 2 solubility in the solvents at lower temperatures, requiring smaller absorber diameter and lower solvent circulation rates, which offset the cooling requirements. Comparing the lowest LCOC values for the five solvents, the hydrophobic PEGPDMS-1 solvent was the most promising one compared to the other four solvents, due to its lowest capital and operating costs and noncorrosive, which enabled using less expensive materials for the process equipment.

42 ENGINEERING↗

Foaming Dependence on the Interface Affinities of Surfactant-like Molecules

We have explored the relationship between physical properties and foaming behavior of 30 wt % aqueous monoethanolamine (MEA) solutions with three different surfactant-like additives. The additives included one commercial surfactant, cetyltrimethylammonium bromide (CTAB), and two CO 2 capture catalysts that behave as weak surfactants. The physical properties of interest were the additives’ affinity for the liquid–vapor interface and the viscosity, surface tension, and surface elasticity of the solutions. The physical properties were explored using molecular dynamics simulations as well as experiments. The additives’ affinity for the liquid–vapor interface played a key role in the foaming behavior by affecting the interfacial properties (surface tension and surface elasticity) of the aqueous MEA solutions. The solution containing CTAB showed the largest surface tension depression and the largest surface elasticity and resulted in the largest amount of foaming. The two catalyst solutions had almost similar surface tensions but differed in their elasticity. Here, the catalyst solution with higher surface elasticity showed more foaming due to higher foam stability.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Molecular Simulations of CO 2 and H 2 Solubility, CO 2 Diffusivity, and Solvent Viscosity at 298 K for 27 Commercially Available Physical Solvents

CO 2 and H 2 solubilities, CO 2 /H 2 solubility selectivities, CO 2 diffusivities, and solvent viscosities in 27 commercially available physical solvents at 298 K were calculated from molecular simulations using the CHARMM36 all-atom force field for most solvents, and the simulation results were compared with available experimental data in this report. The van der Waals radius parameters for solvents were slightly tuned to reproduce the experimental solvent density. The simulated CO 2 solubilities are comparable with the experimental data, with an average absolute difference of 28%. For the homologous compounds containing the –(OCH 2 CH 2 )– repeat unit, both simulated and experimental data show that CO 2 solubility decreases when the number of repeat units is increased; CO 2 solubilities in these homologous compounds exhibit almost a perfect positive linear correlation with the solvent free-volume fractions. The simulated H 2 solubilities and CO 2 /H 2 solubility selectivities are also comparable with the experimental data, with differences of 22% and 17%, respectively. The H 2 solubilities in all solvents researched here correlate very well with the solvent free-volume fractions, exhibiting a positive linear correlation coefficient of 0.84. Additionally, simulations show that CO 2 solubility decreases when the temperature is increased. In contrast, H 2 solubility increases at elevated temperature, which is partly due to the increased solvent free-volume fraction at elevated temperature. Lastly, although the viscosity difference tends to be large (30%–246%) between simulation and experiment, both simulated and experimental data exhibit a similar solvent viscosity trend. Furthermore, simulations show that CO 2 diffusivities in solvents are very strongly correlated with the solvent viscosities and the relationship between them is given by D$_{CO_{2}}$ = (2.6 ± 0.3) × 10 –9 /η solvent 0.59 ± 0.03.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Application of Surface Tension Model for Prediction of Interfacial Speciation of CO 2 -Loaded Aqueous Solutions of Monoethanolamine

A thermodynamic platform in combination with experimental surface tension data is used to predict the surface phase speciation of CO 2 -loaded aqueous solutions of 30 weight percent (%) monoethanolamine (MEA) at 20, 40, and 60 °C from their corresponding bulk phase speciation. The osmotic coefficient dependency of the surface tension of an electrolyte solution has been employed to estimate the surface tension. In order to calculate the osmotic coefficients, the Pitzer equation for the excess Gibbs energy was applied. According to the results of this study, molecular MEA, and to some extent protonated MEA and the MEA-carbamate have surface propensity and will accumulate at the surface phase. The carbonate ion shows nearly even distribution between bulk and surface phases, and bicarbonate displays a tendency to remain in the bulk phase that increases with CO 2 loading. The differences in the behaviors of protonated MEA, MEA-carbamate, carbonate and bicarbonate are due to differences among their sizes and polarizabilities. Using first principles calculations, the static isotropic dipole polarizabilities for bicarbonate, carbonate, MEA carbamate and protonated MEA were calculated. The bulk and surface phases’ ionic strengths reasonably represent this behavior of ionic species at the surface phase.

03 NATURAL GAS↗

Molecular Simulations of the Thermophysical Properties of Polyethylene Glycol Siloxane (PEGS) Solvent for Precombustion CO 2 Capture

Here, the thermophysical properties for neat polyethylene glycol siloxane solvent (PEGS) along with CO 2 , H 2 , H 2 O, and H 2 S gas absorption in PEGS at 298–373 K were investigated via molecular simulations. The predicted neat PEGS density, heat capacity, surface tension, and CO 2 and H 2 solubilities in PEGS solvent agree reasonably well with the experimental data, with typical differences of 0.8–20%, while the predicted PEGS solvent viscosity is 1.7–2.5 times larger than the experimental data. Gas solubility in PEGS at 298 K decreases in the following order, H 2 O (31000) > H 2 S (230) > CO 2 (33) > H 2 (1), which follows the same order as the gas–PEGS interaction. In contrast, gas diffusivity in PEGS at 298 K decreases in an opposite way, H 2 (1) > CO 2 (0.22) ≈ H 2 S (0.12) > H 2 O (0.018). The numbers in parentheses are the corresponding values relative to H 2 . Compared to the widely studied poly(dimethylsiloxane) (PDMS) solvent, PEGS is more hydrophilic due to its stronger interaction with H 2 O and fewer branched –CH 3 groups, which in turn leads to fewer hydrophobic pockets. The CO 2 /H 2 solubility selectivity in PEGS is larger than that in PDMS due to a stronger interaction with CO 2 in PEGS. Finally, it was found that CO 2 absorption in PEGS could significantly improve the CO 2 –PEGS solution dynamics by 5–6 times, resulting in a decrease in solution viscosity and increase in diffusivity. These CO 2 absorption effects are due to solution volume expansion upon CO 2 absorption compared to the neat PEGS solvent volume and the possibility that CO 2 acts as a “lubricant” to decrease the solvent–solvent interaction.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Understanding the Mechanism of CO 2 Capture by 1,3 Di-substituted Imidazolium Acetate Based Ionic Liquids

Efficient CO 2 capture by ionic liquids needs a thorough understanding of underlying mechanisms of the CO 2 interaction with ionic liquids, especially when it involves chemisorption. In this work we have systematically investigated the mechanism of CO 2 capture by 1,3 di-substituted imidazolium acetate ionic liquids using density functional theory. Solvent effects are analyzed using QM/MM and QM/QM approaches with the help of molecular dynamics simulations and ONIOM methods. The investigation of different stepwise mechanisms shows that CO 2 could be involved in the first step of the reaction mechanism, also a new two-step mechanism is proposed. Furthermore, the final stabilization step is analyzed and pointed out to be responsible for important experimentally-observed features of the reaction.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Ab Initio Calculations of the Interaction between CO 2 and the Acetate Ion

A series of ab initio calculations designed to investigate the interaction of CO{sub 2} with acetate are presented. The lowest energy structure, AC–CO{sub 2}-η{sup 2}, is predicted by CCSD(T)/aVTZ to be bound by -10.6 kcal/mol. Six of the bound complexes have binding energies on the order of -8 kcal/mol, but analysis shows that the η{sup 1}-CT complex is fundamentally different from the others. The η{sup 1}-CT complex is characterized by geometric distortion, large polarization and induction effects and charge transfer whereas the other five complexes have little geometric distortion and negligible charge transfer. The amount of charge that is transferred from the anion to the CO{sub 2} in the η{sup 1}-CT complex is estimated to be about half an electron by NPA, DMA, CHELPG, and Mulliken analyses, whereas the EDA-ALMO-CTA (B3LYP) approach predicts a charge transfer of 75 me{sup –}. However, the transfer of this small amount of charge leads to an energy lowering of -56 kcal/mol, without which the complex would not be bound. The RI-MP2 geometries closely approximate those resulting from the CCSD optimizations, and the optimized second-order opposite spin (O2) method performs well for all the complexes except for the η{sup 1}-CT complex. DFT methods do not reproduce all the ab initio geometries, binding energies and/or energy ordering of these complexes although the range-separated hybrid meta-GGA (M11) and nonlocal (VV10 and vdwDF10) functionals are shown to yield results significantly better than other functionals considered for this system. The fact that there is such variation among DFT methods has implications for DFT-based ab initio molecular dynamics simulations and for the parametrization of classical force fields based on DFT calculations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗