Engineering topics
Publications and source records attributed to Stefanescu, Doru M..
This slide presentation reviews the possible use of molten oxide electrolysis to extract oxygen from the Lunar Regolith. The presentation asserts that molten regolith electrolysis has advanced to be a useful method for production of oxygen and metals in situ on the Moon. The work has demonstrated an 8 hour batch of electrolysis at 5 amps using Iridium inert anodes.
The paper reviews the main issues associated with molten materials transfer and handling on the lunar surface during the operation of a hig h temperature electrowinning cell used to produce oxygen, with molten iron and silicon as byproducts. A combination of existing technolog ies and purposely designed technologies show promise for lunar exploi tation. An important limitation that requires extensive investigation is the performance of refractory currently used for the purpose of m olten metal containment and transfer in the lunar environment associa ted with electrolytic cells. The principles of a laboratory scale uni t at a scale equivalent to the production of 1 metric ton of oxygen p er year are introduced. This implies a mass of molten materials to be transferred consistent with the equivalent of 1kg regolithlhr proces sed.
As part of a project on Molten Materials Transfer and Handling on the Lunar Surface, molten materials containment samples of various ceramics were tested to determine their performance in contact with a melt of lunar regolith simulant. The test temperature was 1600 C with contact times ranging from 0 to 12 hours. Regolith simulant was pressed into cylinders with the approximate dimensions of 1.25 dia x 1.25cm height and then melted on ceramic substrates. The regolith-ceramic interface was examined after processing to determine the melt/ceramic interaction. It was found that the molten regolith wetted all oxide ceramics tested extremely well which resulted in chemical reaction between the materials in each case. Alumina substrates were identified which withstood contact at the operating temperature of a molten regolith electrolysis cell (1600 C) for eight hours with little interaction or deformation. This represents an improvement over alumina grades currently in use and will provide a lifetime adequate for electrolysis experiments lasting 24 hours or more. Two types of non-oxide ceramics were also tested. It was found that they interacted to a limited degree with the melt resulting in little corrosion. These ceramics, Sic and BN, were not wetted as well as the oxides by the melt, and so remain possible materials for molten regolith handling. Tests wing longer holding periods and larger volumes of regolith are necessary to determine the ultimate performance of the tested ceramics.
Electrolytic reduction processes as a means to provide pure elements for lunar resource utilization have many advantages. Such processes have. the potential of removing all the oxygen from the lunar soil for use in life support and for propellant. Electrochemical reduction also provides a direct path for the. production of pure metals and silicon which can be utilized for in situ manufacturing and power production. Some of the challenges encountered in the electrolytic reduction processes include the feeding of the electrolytic cell (the transfer of electrolyte containing lunar soil), the withdrawal of reactants and refined products such as the liquidiron~siliconalloy with a number of impurities, and the spent regolith slag, produced in the hot electrolytic cell for the reduction of lunar regolith. The paper will discuss some of the possible solutions to the challenges of handling molten materials on the lunar surface, as well as the path toward the construction and testing of a proof-of-concept facility.
In this article, an investigation of the interaction between gas porosity and a planar solid/liquid (SL) interface is reported. A two-dimensional numerical model able to accurately track sharp SL interfaces during solidification of pure metals and alloys is proposed. The finite-difference method and a rectangular undeformed grid are used for computation. The SL interface is described through the points of intersection with the grid lines. Its motion is determined by the thermal and solute gradients at each particular point. Changes of the interface temperature because of capillarity or solute redistribution as well as any perturbation of the thermal and solute field produced by the presence of non-metallic inclusions can be computed. To validate the model, the dynamics of the interaction between a gas pore and a solidification front in metal alloys was observed using a state of the art X-ray transmission microscope (XTM). The experiments included observation of the distortion of the SL interface near a pore, real-time measurements of the growth rate, and the change in shape of the porosity during interaction with the SL interface in pure Al and Al-0.25 wt pct Au alloy. In addition, porosity-induced solute segregation patterns surrounding a pore were also quantified.
The distribution of ceramic particles in a metal matrix composite material depends primarily on the interaction of the particles with the solid/liquid interface during the solidification process. A numerical model that describes the evolution of the shape of the solid/liquid interface in the proximity of a foreign particle will presented in this paper. The model accounts for the influence of the temperature gradient and the Gibbs-Thomson and disjoining pressure effects. It shows that for the systems characterized by k(sub p) < k(sub L) the disjoining pressure causes the interface curvature to change its sign in the close-contact particle/interface region. It also shows that the increase of the temperature gradient diminishes the effect of the disjoining pressure. The analysis of the numerical results obtained for a large range of processing conditions and materials parameters has led to the development of an analytical solution for the critical velocity of pushing/engulfinent transition. The theoretical results will be discussed and compared with the experimental measurements performed under microgravity conditions.
A numerical mathematical model capable of accurately describing the evolution of the shape of the solid/liquid interface in the proximity of a foreign particle is presented in this paper. The model accounts for the influence of the temperature gradient and the Gibbs-Thomson and disjoining pressure effects. It shows that for the systems characterized by k(sub P) < k(sub L) the disjoining pressure causes the interface curvature to change its sign in the close-contact particle/interface region. It also shows that the increase of the temperature gradient diminishes the effect of the disjoining pressure. Calculated critical solidification velocities for the pushing/engulfment transition are compared with experimental measurements performed in microgravity conditions.
The Jackson and Hunt (JH) theory has been modified to relax the assumption of isothermal solid liquid interface used in their treatment. Based on the predictions of this modified theory, the traditional definitions of regular and irregular eutectics are revised. For regular eutectics, the new model identifies a range of spacing within the limits defined by the minimum undercooling of the a and beta phases. For the irregular Al-Si eutectic system, two different spacing selection mechanisms were identified: (1) for a particular growth rate, a nearly isothermal interface can be achieved at a unique minimum spacing lambda (sub t); (2) the average spacing (lambda (sub av) greater than lambda (sub t) is essentially dictated by the undercooling of the faceted phase. Based on the modified theoretical model, a semiempirical expression has been developed to account for the influence of the temperature gradient, which is dominant in the irregular Al-Si system. The behavior of the Fe-Fe3C eutectic is also discussed. The theoretical calculations have been found to be in good agreement with the published experimental measurements.
The interaction of an insoluble particle with an advancing solid/liquid interface (SLI) has been a subject of investigation for the past four decades. While the original interest stemmed from geology applications (e.g., frost heaving in soil), researchers soon realized that the complex science associated with such an interaction is relevant to many other scientific fields encompassing metal matrix composites (MMCs), high temperature superconductors, inclusion management in steel, growth of monotectics, and preservation of biological cells. During solidification of a liquid containing an insoluble particle, three distinct interaction phenomena have been experimentally observed: instantaneous engulfment of the particle, continuous pushing, and particle pushing followed by engulfment. It was also observed that for given experimental conditions and particle size there is a critical solidification velocity, V(sub cr), above which a particle is engulfed. During solidification of MMCs pushing leads to particle agglomeration at the grain boundaries and this has detrimental effects on mechanical properties of the casting. Consequently, the process must be designed for instantaneous engulfment to occur. This implies the development of accurate theoretical models to predict V(sub cr), and perform benchmark experiments to test the validity of such models. Although considerable progress has been made in understanding the pushing/engulfment phenomenon (PEP), its quantification in terms of the material and processing parameters remains a focus of research. Since natural convection currents occurring during terrestrial solidification experiments complicate the study of PEP, execution of experiments on the International Space Station (ISS) has been approved and funded by NASA. Extensive terrestrial (1g) experiments and preliminary micro-gravity (mu g) experiments on two space shuttle missions have been conducted in preparation for future experiments on the ISS. The investigated systems included metal-ceramic particles (pure aluminum - zirconia particles) and transparent organic - non-reactive particles (succinonitrile - polystyrene and biphenyl - glass). This paper will discuss the experimental results obtained in both lg and pg conditions and the influence of the natural convection on V(sub cr). A summary of past mathematical models and our recent theoretical developments will also be presented to explain the experimentally observed particle/SLI interaction.
In this paper, an investigation of the interaction between gas porosity and a planar solid/liquid (SL) interface is reported. A two-dimensional numerical model able to accurately track sharp SL interfaces during solidification of pure metals and alloys is proposed. The finite difference method and a rectangular undeformed grid are used for computation. The SL interface is described through the points of intersection with the grid lines. Its motion is determined by the thermal and solute gradients at each particular point. Changes of the interface temperature because of capillarity or solute redistribution as well as any perturbation of the thermal and solute field produced by the presence of non-metallic inclusions can be computed. To validate the model, the dynamics of the interaction between a gas pore and a solidification front in metal alloys was observed using a state of the art X-ray Transmission Microscope. The experiments included observation of the distortion of the SL interface near a pore, real-time measurements of the growth rate and the change in shape of the porosity during interaction with an advancing SL interface in pure Al and Al-0.25 wt% Au alloy. In addition, porosity induced solute segregation patterns surrounding a pore were also quantified.
The phenomenon of interaction of particles with solid-liquid interfaces (SLI) has been studied since the mid 1960's. While the original interest stemmed from geology applications (frost heaving in soil), researchers soon realized that fundamental understanding of particles behavior at solidifying interfaces might yield practical benefits in other fields, including metallurgy. In materials engineering the main issue is the location of particles with respect to grain boundaries at the end of solidification. Considerable experimental and theoretical research was lately focused on applications to metal matrix composites produced by casting or spray forming techniques, and on inclusion management in steel. Another application of particle SLI interaction is in the growing of Y1Ba2Cu3O(7-delta) (123) superconductor crystals from an undercooled liquid. The oxide melt contains Y2Ba1Cu1O5 (211) precipitates, which act as flux pinning sites. The experimental evidence on transparent organic materials, as well as the recent in situ observations on steel demonstrates that there exist a critical velocity of the planar SLI below which particles are pushed ahead of the interface, and above which particles are engulfment. The engulfment of a SiC particle in succinonitrile is exemplified. However, in most commercial alloys dendritic interfaces must be considered. Indeed, most data available on metallic alloys are on dendritic structures. The term engulfment is used to describe incorporation of a particle by a planar or cellular interface as a result of local interface perturbation, as opposed to entrapment that implies particle incorporation at cells or dendrites boundaries. During entrapment the particles are pushed in the intercellular or interdendritic regions and then captured when local solidification occurs. The physics of these two phenomena is fundamentally different.
The interaction of an insoluble particle with a growing solid-liquid interface (SLI) has been a subject of investigation for the four decades. For a metallurgist or a material scientist understanding the fundamental physics of such an interaction is relevant for applications that include distribution of reinforcement particles in metal matrix composites, inclusion management in castings, and distribution of Y2Ba1Cu1O5 (211) precipitates (flux pinning sites) in Y1Ba2Cu3O7 (123) superconducting crystals. The same physics is also applicable to other areas including geological applications (frost heaving in soils) and preservation of biological cells. Experimentally this interaction can be quantified in terms of a critical growth velocity, Vcr, of the SLI below which particles are pushed ahead of the advancing interface, and above which the particles are engulfed. Past experimental evidence suggests that this Vcr is an inverse function of the particle radius, R. In order to isolate the fundamental physics that governs such a relationship it is necessary to minimize natural convection at the SLI that is inherent in ground based experiments. Hence for the purpose of producing benchmark data (Vcr vs. R) PEP is a natural candidate for micro-gravity experimentation. Accordingly, experiments with pure Al containing a dispersion of ZrO2 particles and an organic analogue, succinonitrile (SCN) containing polystyrene particles have been performed on the LMS and USMP-4 mission respectively. In this paper we will summarize the experimental data that was obtained during these two micro-gravity missions and show that the results differ compared to terrestrial experiments. We will also discuss the basic elements of our analytical and numerical model and present a comparison of the predictions of these models against micro-gravity experimental data. Finally. we will discuss our future experimental plan that includes the ISS glovebox and MSRRl.
The distribution of insoluble particles in a metal casting depends primarily on the interaction of the particles with the solid/liquid interface (SLI) during the solidification process. Whether a particle will be engulfed or continuously pushed by SLI is essentially determined by the balance of forces acting on the particle. An important component of this force balance is the drag force generated by the particle motion in front of the SLI. Previously developed mathematical models for particle/SLI interaction made use of steady-state solutions of this force provided by the lubrication theory. However, our numerical model based on the SLI tracking approach shows that not only the steady-state approach is inappropriate to model the interaction process but also that even at steady-state the theoretical solution underestimates the drag force. A regression analysis of steady-state numerical solutions for cylindrical particles moving normal to a flat SLI gave a relationship of the form F(sub d) (exp num) = (square root of 3) pi eta V(sub p)((R(sub p) / d) (exp 10 gamma/3)) as compared to the theoretical solution F(sub d) (exp theor) = 3 X (square root of 2) pi eta V(sub p)((R(sub p) / d) (exp 3/2)) where F(sub d) is the drag force, eta is the dynamic viscosity of the fluid, V(sub p) is the particle velocity, R(sub p) is the particle radius, gamma is Euler's constant (gamma is approximately equal to 0.577), and d is the width of the gap between the particle and the SLI. Model validation as well as the influence of the interface shape on the value of F(sub d) will also be discussed.
The phenomenon of interaction of particles with solid-liquid interfaces that results in particle engulfment or pushing (PEP) has been Studied since mid 1960's. While the original interest stemmed from geology applications (frost heaving in soil), it was recognized early that understanding particle behavior at solidifying interfaces mi ht yield 9 practical benefits in other fields. In metallurgical applications the issue is the location of particles with respect to grain boundaries at the end of solidification. Considerable amount of experimental and theoretical research was lately focused on applications to metal matrix composites produced by casting; or spray forming techniques. Another application of PEP is in the growing of Y1Ba2CU3O7-delta(123) superconductor crystals from an undercooled liquid. The oxide melt contains Y2Ba1CU1O5 (211) precipitates, which act as flux pinning sites. The paper presents results of PEP micro-gravity research performed by the authors on two shuttle missions using metallic and polymeric materials. In addition. a discussion on the theoretical aspects of the physics of PEP is offered. Analytical and numerical models for planar solidification interfaces developed by the authors are used to explain the experimental results. Shortcomings of steady-state models are emphasized. A numerical model that includes the effect of the solutal field and of natural convection is introduced. A discussion of phenomena associated with dendritic solidification based on experimental observations is also offered. A mechanism of engulfment is proposed.
Numerical modeling was Undertaken to analyze the influence of both radial and axial thermal gradients on convection patterns and velocities claiming solidification of pure Al and an Al-4 wt% Cu alloy. The objective of the numerical task was to predict the influence of convective velocity on an insoluble particle near a solid/liquid (s/l) interface. These predictions were then be used to define the minimum gravity level (q) required to investigate the fundamental physics of interactions between a particle and a s/l interface. This is an ongoing NASA founded flight experiment entitled "particle engulfment and pushing by solidifying interfaces (PEP)". Steady-state calculations were performed for different gravity levels and orientations with respect to the gravity vector The furnace configuration used in this analysis is the quench module insert (QMI-1) proposed for the Material Science Research Facility (MSRF) on board the International Space Station (ISS). The general model of binary alloy solidification was based on the finite element code FIDAP. At a low g level of 10(exp -4) g(sub o) (g(sub o) = 9.8 m/square s) maximum melt convection was obtained for an orientation of 90 deg. Calculations showed that even for this worst case orientation the dominant forces acting on the particle are the fundamental drag and interfacial forces.
The distribution of insoluble particles in a metal casting depends primarily on the interaction of the particles with the solid/liquid interface (SLI) during the solidification process. The balance of the forces acting on the particle essentially determines whether a particle will be engulfed or pushed by the SLI. An important component of this force balance is the drag force generated by the particle motion in front of the SLI. Previously developed mathematical models for particle/SLI interaction made use of steady-state solutions of this force provided by the lubrication theory. However, our numerical model based on the SLI tracking approach shows that the steady-state approach is inappropriate to model the interaction process and that at steady-state the theoretical solution underestimates the drag force. It was found that regression analysis of steady-state numerical solutions for cylindrical particles moving normal to a flat SLI gives a relationship of the form: Abstract The distribution of insoluble particles in a metal casting depends primarily on the interaction of the particles with the solid/liquid interface (SLI) during the solidification process. The balance of the forces acting on the particle essentially determines whether a particle will be engulfed or pushed by the SLI. An important component of this force balance is the drag force generated by the particle motion in front of the SLI. Previously developed mathematical models for particle/SLI interaction made use of steady-state solutions of this force provided by the lubrication theory. However, our numerical model based on the SLI tracking approach shows that the steady-state approach is inappropriate to model the interaction process and that at steady-state the theoretical solution underestimates the drag force. It was found that regression analysis of steady-state numerical solutions for cylindrical particles moving normal to a flat SLI gives a relationship of the form: F(sub D, sup num) =sqoare root of 3(pi)(eta)V(sub p)(R(sub p)/d)(sup 10(gamma)/3). This is to compared to the solution provided by the lubrication theory: F(sub D), sup theor) = 3 square root of 2(pi)(eta)V(sub p)(R(sub p)/d)(sub 3/2), where F(sub D) is the drag force, eta is the dynamic viscosity of the fluid, V(sub p) is the particle velocity, R(sub p) is the particle radius, gamma is Euler's constant (gamma approx. = 0.577), and d is the width of the gap between the particle and the SLI. The domain on which the equations proposed by the lubrication theory are relevant is clearly identified in the paper. The numerical model was then validated against the classical lubrication theory within the domain of its validity.
The scientific objectives of the work on Particle Engulfment and Pushing by Solidifying Interfaces (PEP) include: (1) to enhance the fundamental understanding of the physics of interaction between inert particles and the solidification interface, and (2) to investigate aspects of melt processing of particulate metal matrix composites in the unique microgravity environment that will yield some vital information for terrestrial applications. The proposal itself calls for a long-term effort on the Space Station. This paper reports on ground experiments performed to date, as well as on the results obtained from two flight opportunities, the LMS mission (1996) and the USMP-4 mission (1997).
Numerical modeling was undertaken to analyze the influence of radial thermal gradient on solid/liquid interface shape and convection patterns during solidification of pure Al and Al-4 wt. % Cu alloy. Steady state calculations were performed for different gravity levels and orientations. Furthermore, transient modeling was undertaken to investigate effect of the solidification velocity. The furnace configuration used in this analysis is the proposed International Space Station Furnace. Results from a thermal model of the furnace core were used as initial boundary conditions for solidification modeling. The Solidification model was adopted from previous work and was based on the finite element code FIDAP. Thermocouple data and quenched interface shape from a pure Al sample flown on the Life Sciences and Microgravity Spacelab (LMS) mission, July 1996 was used for model validation. Good agreement was obtained between the predicted interface shape and that measured from the quenched LMS sample. It was found that the imposed temperature boundary condition must be sufficiently smooth for the heat fluxes in the model to be self-consistent. The model predicted that alloy sample Al-Cu is more sensitive to variations in the gravity level compared to pure Al. For Al-Cu alloy, solute diffusivity is approximately 10(exp 4) times smaller than thermal diffusivity of pure Al. Hence, in a microgravity environment the weak convection has no measurable effect on the heat fluxes, but is still strong enough to affect concentration distribution. Since the alloy melting temperature is determined by concentration the interface shape depends on the level of convection. This was found not to be the case for pure metal.