Search NASA⌕ Search

Engineering topics

Stewart, V. R.

Publications and source records attributed to Stewart, V. R..

15 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

An experimental investigation of the ground vortex created by a moving jet

A 1 inch circular jet moving over a fixed ground board was studied in the NASA Langley Research Center Vortex Research Center. The jet passing over the ground board at a height of three nozzle diameters creates a ground vortex which was measured by a pattern of Endevco high response pressure transducers. The results are compared to existing data to determine the effect of the ground boundary eliminated by the moving jet. The penetration of the vortex both forward of and latterly to the impact point of the jet on the ground. The resulting ground vortex penetration forward of the impact point is reduced by approximately 30 percent and the lateral penetration is reduced by 50 percent over that experienced from a stationary jet over a stationary ground board with a free stream velocity.

Stewart, V. R.↗
NASA NTRS1989

Characteristics of the ground vortex formed by a jet moving over a fixed ground plane

This paper discusses an experimental study conducted in the Langley Vortex Facility to investigate the effects on the ground vortex of the jet passing over a fixed ground board. A jet impacting the ground can form a vortex which may materially affect the aerodynamic characteristics of a STOL airplane operating near the ground. Several studies have been done with a stationary jet exiting near and perpendicular to fixed ground board. The resulting ground effects have been documented in terms of ground vortex and aerodynamic characteristics. The ground boundary layer created in a wind tunnel facility, however is thought to affect the extent of the ground vortex. This paper reports on an investigation utilizing an isolated moving jet to eliminate the ground boundary layer. The results are compared to the existing data base and show a 30 percent decrease in the vortex penetration shown by the stationary jet conditions.

Kemmerly, G. T.↗
NASA NTRS1987

Low speed wind tunnel test of a propulsive wing/canard concept in the STOL configuration. Volume 1: Test description and discussion of results

A propulsive wing/canard model was tested at STOL operating conditions in the NASA Langley Research Center 4 x 7 meter wind tunnel. Longitudinal and lateral/directional aerodynamic characteristics were measured for various flap deflections, angles of attack and sideslip, and blowing coefficients. Testing was conducted for several model heights to determine ground proximity effects on the aerodynamic characteristics. Flow field surveys of local flow angles and velocities were performed behind both the canard and the wing. This is volume 1 of a 2 volume report. The model, instrumentation, and test procedures are described. An analysis of the data is included.

Stewart, V. R.↗
NASA NTRS1987

Low speed wind tunnel test of a propulsive wing/canard concept in the STOL configuration. Volume 2: Test data

A propulsive wind/canard model was tested at STOL operating conditions in the NASA Langley Research Center 4 x 7 meter wind tunnel. Longitudinal and lateral/directional aerodynamic characteristics were measured for various flap deflections, angles of attack and sideslip, and blowing coefficients. Testing was conducted for several model heights to determine ground proximity effects on the aerodynamic characteristics. Flow field surveys of local flow angles and velocities were performed behind both the canard and the wing. This is volume 2 of a 2 volume report. All of the test data in three appendices are presented. Appendix A presented tabulated six component force and moment data, Appendix B presents tabulated wing pressure coefficients, and Appendix C presents the flow field data.

Stewart, V. R.↗
NASA NTRS1987

Effects of ground proximity on a low aspect ratio propulsive wing/canard configuration

The effect of near proximity to the ground are investigated on a low aspect ratio propulsive wing/canard concept at STOL conditions. Data were obtained on a wing/body and wing/body/canard configuration at various heights above the ground, ranging from free air to approximately 1/4 of the mean aerodynamic chord (MAC) above the ground. The data presented and discussed include force and moment coefficients, surface pressure distributions, and downwash angles measured one MAC behind the wing. The test technique, model requirements, and special considerations required for testing these configurations are also discussed. Special model requirements included evenly distributed exit nozzle pressures along four separate nozzles of lengths of one and two feet with only one air supply to the model. Test techniques must recognize and deal with the ground boundary layer as well as the air supply pressure measurement and management.

Stewart, V. R.↗
NASA NTRS1986

Pretest Report for the Full Span Propulsive Wing/Canard Model Test in the NASA Langley 4 x 7 Meter Low Speed Wind Tunnel Second Series Test

A full span propulsive wing/canard model is to be tested in the NASA Langley Research Center (LaRC) 4 x 7 meter low speed wind tunnel. These tests are a continuation of the tests conducted in Feb. 1984, NASA test No.290, and are being conducted under NASA Contract NAS1-17171. The purpose of these tests is to obtain extensive lateral-directional data with a revised fuselage concept. The wings, canards, and vertical tail of this second test series model are the same as tested in the previous test period. The fuselage and internal flow path have been modified to better reflect an external configuration suitable for a fighter airplane. Internal ducting and structure were changed as required to provide test efficiency and blowing control. The model fuselage tested during the 1984 tests was fabricated with flat sides to provide multiple wing and canard placement variations. The locations of the wing and canard are important variables in configuration development. With the establishment of the desired relative placement of the lifting surfaces, a typically shaped fuselage has been fabricated for these tests. This report provides the information necessary for the second series tests of the propulsive wing/canard model. The discussion in this report is limited to that affected by the model changes and to the second series test program. The pretest report information for test 290 which is valid for the second series test was published in Rockwell report NR 83H-79. This report is presented as Appendix 1 and the modified fuselage stress report is presented as Appendix 2 to this pretest report.

Stewart, V. R.↗
NASA NTRS1985

Aerodynamic characteristics of a propulsive wing-canard concept at STOL speeds

A full span model of a wing/canard concept representing a fighter configuration has been tested at STOL conditions in the NASA Langley 4 x 7 meter tunnel. The results of this test are presented, and comparisons are made to previous data of the same configuration tested as a semispan model. The potential of the propulsive wing/canard to develop very high lift coefficients was investigated with several nozzle spans (nozzle aspect ratios). Although longitudinal trim was not accomplished with the blowing distributions and configurations tested, the propulsive wing/canard appears to offer an approach to managing the large negative pitching moments associated with trailing edge flap blowing. Also presented are data showing the effects of large flap deflections and relative wing/canard positions. Presented in the appendix to the report are limited lateral-directional and ground effects data, as well as wing downwash measurements.

Stewart, V. R.↗
NASA NTRS1984

The aerodynamic characteristics of a propulsive wing/canard concept in STOL

The potential of the propulsive wing in developing very high lift coefficients for STOL operation has been investigated with several nozzle aspect ratios. The use of the propulsive wing/canard appears to offer an approach to managing the large negative pitching moments associated with trailing-edge blowing. A full-span model of a wing/canard concept representing a fighter configuration has been tested at STOL conditions in the Langley 4 by 7 Meter Tunnel. The results of this test are presented, and comparisons are made to previous tests of the same configuration tested as a semispan model (Stewrt, 1983). Also presented are data showing the effects of large flap deflection and the effect of nozzle span. Comparisons of the test results with jet-flap theory are made and indicate good agreement.

Stewart, V. R.↗
NASA NTRS1983

Experimental wing and canard jet-flap aerodynamics

The effects of upper surface blowing on the aerodynamics of a 1/2-span wing/body/canard configuration are shown. The results expand a data base that is limited at high subsonic Mach numbers (M = 0.6-0.9), data that are needed if computational techniques are to be developed for the complex flowfields generated by jet blowing. At lift coefficients greater than about 1.0, the thrust removed drag coefficient was lower with jet blowing than without jet blowing. This favorable effect increased with increasing jet blowing coefficient, and, for a fixed coefficient, simultaneous wing/canard jet blowing was slightly more effective than blowing either surface alone.

Smeltzer, D. B.↗
NASA NTRS1981

An investigation of the use of a propulsive wing/canard concept for improved maneuvering

The propulsive wing concept is an extension of the flap boundary layer control utilized on several aircraft configurations. Several studies have been made regarding the benefits of the propulsive wing in STOL operation. However, the propulsive wing/canard provides performance benefits also in areas other than STOL. It is expected to improve the maneuvering capability by providing reduced drag at high lift coefficients without appreciably affecting the low lift drag. An increase in the buffet free load factor can also be expected with the blown wing and canard. Attention is given to a program to investigate the wing/canard at maneuvering conditions, and tests at ranges of blowing coefficients equivalent to STOL operation.

Stewart, V. R.↗
NASA NTRS1981

A study of a VTOL thrusting ejector in low speed flight, volume 1

Low speed aerodynamic characteristics of a thrust augmenter wing suitable for vertical operation were investigated. Wind tunnel test results on the ejector and a similar configuration with a blown flap are analyzed. The configurations represented a VTOL concept at conditions of thrust deflections required for low forward speed flight. The model tested had an unswept untapered wing. Specific data included normal longitudinal forces and monents, surface pressures, ejector exit surveys, and flow field surveys behind the wing.

Stewart, V. R.↗
NASA NTRS1981

A study of a VTOL thrusting ejector in low speed flight, volume 2

An experimental investigation of V/STOL thrust augmenter wings in flight at slow forward speeds is reported. Two rectangular planforms of differing relative chord lengths were tested. The augmenters were positioned in the aft portion of the wing to produce increases in circulation lift. Two blown flap configurations were tested for comparison. Surface pressures as well as total forces and moments were obtained on the semispan models at two flap deflections and a range of momentum coefficients. Tabulations of surveys at the pressure augmenter exit, downwash surveys downstream of the wing, and force and moment data are included.

Stewart, V. R.↗
NASA NTRS1979

The characteristics of a lift cruise fan V/STOL configuration in near proximity to a small deck with finite edge positions

Two V/STOL model configurations utilizing lift-cruise-fans for the propulsion system have been tested in the presence of a small landing platform with finite deck edge positions. Results and analysis of these tests are presented. The model was tested at both static (zero velocity) and forward speed conditions with several heights and deck edge positions. Configurations utilizing three fans and four fans were investigated. Incremental forces and moments induced by the various deck edge positions are analyzed as relating to the model height above the ground and the thrust velocity relationships. The test and analysis show the induced forces to be relatively unaffected by deck edge.

Stewart, V. R.↗
NASA NTRS1979

Low speed wind tunnel test of ground proximity and deck edge effects on a lift cruise fan V/STOL configuration, volume 1

The characteristics were determined of a lift cruise fan V/STOL multi-mission configuration in the near proximity to the edge of a small flat surface representation of a ship deck. Tests were conducted at both static and forward speed test conditions. The model (0.12 scale) tested was a four fan configuration with modifications to represent a three fan configuration. Analysis of data showed that the deck edge effects were in general less critical in terms of differences from free air than a full deck (in ground effect) configuration. The one exception to this was when the aft edge of the deck was located under the center of gravity. This condition, representative of an approach from the rear, showed a significant lift loss. Induced moments were generally small compared to the single axis control power requirements, but will likely add to the pilot work load.

Stewart, V. R.↗