Search NASA⌕ Search

Engineering topics

Stimpson, Shane

Publications and source records attributed to Stimpson, Shane.

At least 19 records

MPACT 4.4 Theory Manual

MPACT is a three-dimensional (3D) full-core neutron transport code capable of calculating subpin power distributions. Calculations are based on the Boltzmann transport equation for neutron fluxes for problems in which the detailed geometrical configuration of fuel components such as the pellet and cladding are explicitly retained. The cross-section data needed for the neutron transport calculation are obtained directly from a multigroup cross section library, which has traditionally been used by lattice physics codes to generate few-group homogenized cross sections for nodal core simulators. Hence, MPACT assumes neither a priori homogenization nor group condensation for the full core spatial solution. The 3D MPACT transport solution can be obtained using the method of characteristics (MOC), which employs discrete ray tracing within each fuel pin. However, for practical reactor applications, the direct application of MOC to 3D core configurations requires an excessive amount of memory and computing time due to the very large number of rays. For practical 3D full-core calculations, MPACT commonly uses an approximate “2D/1D” method that treats the radial (x and y) variables differently from the axial (z) variable. In particular, the radial dependence of the solution is calculated using transport theory, and the axial dependence is calculated using diffusion or P 3 theory. The 2D/1D method requires the core to be divided into a vertical stack of axial slices with a thickness of Δ z ≈ 5–10 cm. Each axial slice is divided radially into coarse spatial cells with boundaries that usually constitute the pin cell boundaries, for which Δ x = Δ y ≈ 1.5 cm. Then, each coarse radial cell (pin cell) is divided into 50–100 fine radial cells, which resolve the angular flux in the fuel, cladding, and moderator regions.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

MPACT Verification and Validation Manual Version 4.4

As the VERA SQA plan requires, it is the responsibility of the University of Michigan (UM) and Oak Ridge National Laboratory (ORNL), as co-owners of MPACT, to ensure that verification and validation activities are performed and documented in a V&V manual with supporting publications and CASL technical reports which can be provided for reference and distribution within VERA. This document provides the current revision of the MPACT verification and validation (V&V) manual and describes the current state of MPACT V&V and updates the plans for future MPACT V&V activities. The following sections provide an overview of the V&V process used in MPACT, as well as a summary of the status of each component of V&V in the code.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

MPACT Verification and Validation Manual (V.4.3)

As the VERA SQA plan requires, it is the responsibility of the University of Michigan (UM) and Oak Ridge National Laboratory (ORNL), as co-owners of MPACT, to ensure that verification and validation activities are performed and documented in a V&V manual with supporting publications and CASL technical reports which can be provided for reference and distribution within VERA. This document provides the current revision of the MPACT verification and validation (V&V) manual and describes the current state of MPACT V&V and updates the plans for future MPACT V&V activities. The following sections provide an overview of the V&V process used in MPACT, as well as a summary of the status of each component of V&V in the code.

97 MATHEMATICS AND COMPUTING↗

MPACT Theory Manual (V.4.3)

This manual presents the theory underlying the three-dimensional (3D) whole-core, pin-resolved neutron transport calculation methodologies employed in the MPACT code. MPACT’s primary goal is to provide accurate sub-pin power distributions in a computationally efficient manner. To accomplish this, MPACT offers several different transport method options. The 2D/1D method, in which 3D problems are decomposed into an axial stack of radial “slices,” is currently the most commonly used. In this option, two-dimensional (2D) planar solutions are provided by the method of characteristics (MOC), and axial solutions are provided via one-dimensional (1D) approximate diffusion, or P3 solutions. The radial and axial solutions are coupled by (i) axial and radial transverse leakages, and (ii) a global 3D coarse mesh finite difference (CMFD) solve, which provides both acceleration and stability to the solution iteration scheme. The subsequent chapters of this manual present a range of topics, including MOC, CMFD, axial nodal transport solvers, 2D/1D, self-shielding, depletion, thermal-hydraulics, and transient methods. Development of the underlying theory of the 2D/1D method is presented, diagrams are included to highlight important algorithmic flow, and important concepts are discussed as appropriate. This manual is intended to be self-sufficient, but references to published articles and other materials are included for further reading. MPACT is a relatively new code, with new capabilities and many computational methods that did not exist until recently. This manual is an even newer document, with chapters written by several different code contributors working under time constraints. For these reasons, the manual is not yet complete and finalized. Future versions of this manual will address current deficiencies.

97 MATHEMATICS AND COMPUTING↗

MPACT Programmer's Manual (V.4.3)

Figure 1 shows a high-level call chart for MPACT. The call chart uses the actual procedure names, starting with the main program name, MPACT. The only exception is the italicized names where the upstream procedure contains a number of subroutines calls. These calls are logically separated into blocks, such as setup basic info/inputs. Brief descriptions of what the procedure accomplishes are provided where needed. More detailed procedure information, including procedure arguments and definitions, can be found directly in the procedure header in the MPACT source code or Doxygen documentation (http://www.doxygen.nl/).

97 MATHEMATICS AND COMPUTING↗

MPACT Software Management Plan (V.4.3)

The MPACT code solves a discretized form of the Boltzmann transport equation on a wide variety of geometries and is distributed with a multigroup neutron cross section library. MPACT provides an advanced geometrically resolved neutral-particle transport capability to solve the flux distribution throughout the entire problem geometry, and it can model the isotopic depletion, decay, and activation of materials. The flux solution in MPACT is provided using a 2D/1D synthesis method within the framework of the 3D coarse mesh finite difference (CMFD) method for which axial and radial correction factors are obtained from 2D method of characteristics (MOC) and 1D nodal expansion method (NEM), PN, or SN. Other key characteristics of the MPACT code include the subgroup method and the embedded self-shielding method (ESSM) for resonance treatment, depletion capability based on the ORIGEN exponential matrix method, and a simplified thermal-hydraulics method for temperature/fluid feedback. The sole purpose of the simplified feedback model is to provide a mechanism for testing during code development and to provide a limited capability for educational applications. Work performed at the code level supports the VERA-QA-001, quality assurance program plan (QAPP) and VERA-QA-002, VERA Software Quality Assurance Plan.

97 MATHEMATICS AND COMPUTING↗

Simulation of the BEAVRS benchmark using VERA

The Virtual Environment for Reactor Applications (VERA) is being developed by the Consortium for the Advanced Simulation of Light Water Reactors (CASL). Here, VERA is used to perform the Benchmark for Evaluation and Validation of Reactor Simulations (BEAVRS), which provides two cycles’ worth of operating power history, along with a full, detailed description of the geometry, and measured data. Cycle 1 and 2 are simulated with VERA and the results are compared to the measured zero power physics tests, critical boron concentration, and flux maps.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Spatial decomposition of structured grids for nuclear reactor simulations

Spatial decomposition methods based on graph partitioning are developed and implemented in the high fidelity neutron transport code MPACT. These graph-based spatial decomposition methods are more general than previous decomposition methods and typically provide better load balance and reduced runtimes due to their improved parallel efficiency. Correlations are drawn between simulation runtime and the balance of the partition for 2D simulations. Comparisons are made using partition balance metrics for different decomposition schemes in 2D and 3D simulations. Finally, for typical ranges of subdomains, graph-based partitioning methods offer significant reductions to runtimes. However, for highly decomposed problems, these graph-based methods may decrease convergence rates, thus reducing parallel efficiency compared to older methods.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

VERA Infrastructure

The Virtual Environment for Reactor Applications (VERA) Infrastructure provides the infrastructure to build, configure, test, install, and package for release the VERAS suite of codes that is being developed by the Consortium for the Advanced Simulation of Light-water reactors (CASL). It includes the list of codes that can be built within VERA, the location on the configuration-controlled CASL development computer, the version number used in any particular software installation, the location of the third-party libraries used for testing VERA on a suite of the CASL testing and development computers, and the scripts to configure, build, test, install, and package for release a particular version of VERA. The VERA Infrastructure contains a list of scripts, configuration options, and utilities that are specific to CASL, but contain no physics or numeric, nuclear technology, or encryption technology.

Baird, Mark↗

Verification of Vessel Fluence and Excore Modeling with VERA

This document outlines the completion of the L2:RTM.P17.01 milestone to deliver and report verification of vessel fluence and excore modeling capabilities in VERA to Advanced Modeling Applications (AMA). It gives details on the unit testing and initial verification of vessel fluence and excore detector calculations performed with VERA, as well as the plotting capabilities in VERAView. This capability is now ready for further testing and verification and validation by AMA.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Pellet-clad mechanical interaction screening using VERA applied to Watts Bar Unit 1, Cycles 1–3

The Consortium for Advanced Simulation of Light Water Reactors (CASL) aims to provide high-fidelity multiphysics simulations of light water nuclear reactors. To accomplish this, CASL is developing the Virtual Environment for Reactor Applications (VERA), which is a suite of code packages for thermal hydraulics, neutron transport, fuel performance, and coolant chemistry. As VERA continues to grow and expand, there has been an increased focus on incorporating fuel performance analysis methods. One of the primary goals of CASL is to estimate local cladding failure probability through pellet-clad interaction, which consists of both pellet-clad mechanical interaction (PCMI) and stress corrosion cracking. Estimating clad failure is important to preventing release of fission products to the primary system and accurate estimates could prove useful in establishing less conservative power ramp rates or when considering load-follow operations.While this capability is being pursued through several different approaches, the procedure presented in this article focuses on running independent fuel performance calculations with BISON using a file-based one-way coupling based on multicycle output data from high fidelity, pin-resolved coupled neutron transport–thermal hydraulics simulations. This type of approach is consistent with traditional fuel performance analysis methods, which are typically separate from core simulation analyses. A more tightly coupled approach is currently being developed, which is the ultimate target application in CASL.Recent work simulating 12 cycles of Watts Bar Unit 1 with VERA core simulator are capitalized upon, and quarter-core BISON results for parameters of interest to PCMI (maximum centerline fuel temperature, maximum clad hoop stress, and minimum gap size) are presented for Cycles 1–3. In conclusion, based on these results, this capability demonstrates its value and how it could be used as a screening tool for gathering insight into PCMI, singling out limiting rods for further, more detailed analysis.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Flexible Spatial Partitions in MPACT Through Module-Based Data Passing

As part of the Consortium for Advanced Simulation of Light Water Reactors (CASL), the Virtual Environment for Reactor Applications (VERA) is being developed to provide high-fidelity multiphysics simulations of nuclear reactor cores. The MPACT code being developed collaboratively by Oak Ridge National Laboratory and the University of Michigan is the primary deterministic neutron transport solver available within VERA. MPACT employs the 2D/1D method to solve 3D problems using 2D method of characteristics (MOC) radial transport solvers with 1D nodal expansion method-based P3 (NEM-P3) axial transport solvers, which are coupled using axial and radial transverse leakages. A 3D coarse mesh finite difference (CMFD) solver is used to provide accelerated convergence and stability. Quarter-core problems in MPACT are typically run on moderately sized clusters ({approx}500-10,000 cores). As such, it relies heavily on spatial decomposition, both radially and axially, using MPI data communication along spatial domain boundaries to pass angular flux boundary condition and neighboring data. The initial spatial decomposition strategy implemented into MPACT overlaid a Cartesian grid over the core to form the domain boundaries. With this approach, a single buffer spanning across the entire boundary between two spatial domains is passed to a domain's neighbor. Additionally, only one neighboring domain index was allowed in each direction. For example, the entire eastern boundary of a domain must be the entire western boundary of the corresponding neighbour's domain. This implementation helped to execute cases on several thousand cores, where substantial radial decomposition was used. The default for several years was to use assembly decomposition, which yielded 73 radial partitions in the Watts Bar Unit 1 (WBN1) models being analyzed. However, as CASL formed stronger connections with industry partners, there was a strong push to allow MPACT to run on fewer cores, preferably in the 500-1,000 core range. Such cases require much less radial decomposition, typically with 8-16 radial domains on each plane. Unfortunately, the previous decomposition strategy is very limited in its ability to yield well-balanced domains, and it does not permit partitions with an arbitrary number of domains, particularly with small numbers of radial domains (3, 5, 7, 11, 13, etc.). With these limitations, a more flexible approach that provided more even-load balancing was needed. The details of this new strategy are outlined here, along with insights to its advantages. The examples provided are for the WBN1 core, which has been the focus of several initial CASL analyses. It is worth noting that spatial decomposition strategies have been employed in many codes with focus on a number of different transport methodologies. The references cited are not exhaustive as this has been very important research topic across many areas.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Demonstration of Load-Follow Operations with Standalone BISON through VERA

As part of the Consortium for Advanced Simulation of Light Water Reactors (CASL), the Virtual Environment for Reactor Applications (VERA) is being developed to provide high-fidelity multiphysics simulations of nuclear reactor cores. VERA contains a number of single physics packages that are coupled together. MPACT is the primary deterministic neutron transport solver, CTF provides thermal hydraulics solutions, and BISON - which is built off of the MOOSE framework - is used for fuel performance simulations. Over the past year, a standalone BISON capability has been developed using a one-way coupling between MPACT/CTF coupling calculations and BISON. This has allowed CASL contributors to gain insight into the fuel performance characteristics while a more tightly coupled methodology between MPACT, CTF, and BISON has been under development. The standalone capability has been used to simulate Watts Bar Unit 1 (WBN1) Cycles 1-3 and to screen for quantities of interest to pellet-clad interaction in Cycles 6-7. The simulation and screening results are presented here. CASL recently partnered with Exelon and the University of Illinois at Urbana Champaign (UIUC) to begin simulating some of Exelon's plants, with particular focus on load-follow operations. In such operations, the power output from the plant will vary based on the demand or anticipated demand at the time. For example, demand is much lower late at night than during the day when people are awake, so it operating the plant at lower power in the evenings could be advantageous. Historically, nuclear power generation has been among the cheapest sources of energy, so most plants in the United States have been operated at full power except for outages and various small scale events. However, in the current economic climate, priorities have changed. A number of questions arise when load-follow operations are considered, particularly with respect to VERA's tools and capabilities. Can the coupled neutronics and thermal hydraulics simulations with MPACT and CTF perform well without substantial convergence issues? Can BISON handle the somewhat rapid power changes present with load-follow? Will clad hoop stresses be alarmingly high as a result of these power changes? This work addresses these questions and demonstrates operations to assess feasibility and robustness before Exelon and UIUC proceed with their simulations using VERA. To demonstrate load-follow capability, two test problems were developed. The first is a single rod that experiences nominal operations during Cycle 1, and then it simulates 18 months of representative load-follow operations in Cycle 2. This single-rod case was used to test the robustness of MPACT, CTF, and BISON on a typical rod. The second problem is a quarter-core model based on WBN1, Cycle 3, with a single month of load-follow operations inserted into the middle of the cycle. This provides better understanding of the stresses to the clad during the numerous power changes. Sections of this article are adapted from the original, full technical report on this capability.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Improvement of transport-corrected scattering stability and performance using a Jacobi inscatter algorithm for 2D-MOC

The MPACT code, being developed collaboratively by the University of Michigan and Oak Ridge National Laboratory, is the primary deterministic neutron transport solver being deployed within the Virtual Environment for Reactor Applications (VERA) as part of the Consortium for Advanced Simulation of Light Water Reactors (CASL). In many applications of the MPACT code, transport-corrected scattering has proven to be an obstacle in terms of stability, and considerable effort has been made to try to resolve the convergence issues that arise from it. Most of the convergence problems seem related to the transport-corrected cross sections, particularly when used in the 2D method of characteristics (MOC) solver, which is the focus of this work. Here in this paper, the stability and performance of the 2-D MOC solver in MPACT is evaluated for two iteration schemes: Gauss-Seidel and Jacobi. With the Gauss-Seidel approach, as the MOC solver loops over groups, it uses the flux solution from the previous group to construct the inscatter source for the next group. Alternatively, the Jacobi approach uses only the fluxes from the previous outer iteration to determine the inscatter source for each group. Consequently for the Jacobi iteration, the loop over groups can be moved from the outermost loop$-$as is the case with the Gauss-Seidel sweeper$-$to the innermost loop, allowing for a substantial increase in efficiency by minimizing the overhead of retrieving segment, region, and surface index information from the ray tracing data. Several test problems are assessed: (1) Babcock & Wilcox 1810 Core I, (2) Dimple S01A-Sq, (3) VERA Progression Problem 5a, and (4) VERA Problem 2a. The Jacobi iteration exhibits better stability than Gauss-Seidel, allowing for converged solutions to be obtained over a much wider range of iteration control parameters. Additionally, the MOC solve time with the Jacobi approach is roughly 2.0-2.5× faster per sweep. While the performance and stability of the Jacobi iteration are substantially improved compared to the Gauss-Seidel iteration, it does yield a roughly 8$-$10% increase in the overall memory requirement.

97 MATHEMATICS AND COMPUTING↗

VERA Core Simulator methodology for pressurized water reactor cycle depletion

This paper describes the methodology developed and implemented in the Virtual Environment for Reactor Applications Core Simulator (VERA-CS) to perform high-fidelity, pressurized water reactor (PWR), multicycle, core physics calculations. Depletion of the core with pin-resolved power and nuclide detail is a significant advance in the state of the art for reactor analysis, providing the level of detail necessary to address the problems of the U.S. Department of Energy Nuclear Reactor Simulation Hub, the Consortium for Advanced Simulation of Light Water Reactors (CASL). VERA-CS has three main components: the neutronics solver MPACT, the thermal-hydraulic (T-H) solver COBRA-TF (CTF), and the nuclide transmutation solver ORIGEN. This paper focuses on MPACT and provides an overview of the resonance self-shielding methods, macroscopic-cross-section calculation, two-dimensional/one-dimensional (2-D/1-D) transport, nuclide depletion, T-H feedback, and other supporting methods representing a minimal set of the capabilities needed to simulate high-fidelity models of a commercial nuclear reactor. Results are presented from the simulation of a model of the first cycle of Watts Bar Unit 1. The simulation is within 16 parts per million boron (ppmB) reactivity for all state points compared to cycle measurements, with an average reactivity bias of <5 ppmB for the entire cycle. Comparisons to cycle 1 flux map data are also provided, and the average 2-D root-mean-square (rms) error during cycle 1 is 1.07%. To demonstrate the multicycle capability, a state point at beginning of cycle (BOC) 2 was also simulated and compared to plant data. The comparison of the cycle 2 BOC state has a reactivity difference of +3 ppmB from measurement, and the 2-D rms of the comparison in the flux maps is 1.77%. Lastly, these results provide confidence in VERA-CS’s capability to perform high-fidelity calculations for practical PWR reactor problems.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Stability and accuracy of 3D neutron transport simulations using the 2D/1D method in MPACT

A consistent “2D/1D” neutron transport method is derived from the 3D Boltzmann transport equation, to calculate fuel-pin-resolved neutron fluxes for realistic full-core Pressurized Water Reactor (PWR) problems. The 2D/1D method employs the Method of Characteristics to discretize the radial variables and a lower order transport solution to discretize the axial variable. This paper describes the theory of the 2D/1D method and its implementation in the MPACT code, which has become the whole-core deterministic neutron transport solver for the Consortium for Advanced Simulations of Light Water Reactors (CASL) core simulator VERA-CS. Several applications have been performed on both leadership-class and industry-class computing clusters. Results are presented for whole-core solutions of the Watts Bar Nuclear Power Station Unit 1 and compared to both continuous-energy Monte Carlo results and plant data.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

MOC Efficiency Improvements Using a Jacobi Inscatter Approximation

In recent weeks, attention has been given to resolving the convergence issues encountered with TCP 0 by trying a Jacobi (J) inscatter approach when group sweeping, where the inscatter source is constructed using the previous iteration flux. This is in contrast to a Gauss-Seidel (GS) approach, which has been the default to-date, where the scattering source uses the most up-to-date flux values. The former is consistent with CASMO, which has no issues with TCP 0 convergence. Testing this out on a variety of problems has demonstrated that the Jacobi approach does indeed provide substantially more stability, though can take more outer iterations to converge. While this is not surprising, there are improvements that can be made to the MOC sweeper to capitalize on the Jacobi approximation and provide substantial speedup. For example, the loop over groups, which has traditionally been the outermost loop in MPACT, can be moved to the interior, avoiding duplicate modular ray trace and coarse ray trace setup (mapping coarse mesh surface indexes), which needs to be performed repeatedly when group is outermost.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

MPACT Subgroup Self-Shielding Efficiency Improvements

Recent developments to improve the efficiency of the MOC solvers in MPACT have yielded effective kernels that loop over several energy groups at once, rather that looping over one group at a time. These kernels have produced roughly a 2x speedup on the MOC sweeping time during eigenvalue calculation. However, the self-shielding subgroup calculation had not been reevaluated to take advantage of these new kernels, which typically requires substantial solve time. The improvements covered in this report start by integrating the multigroup kernel concepts into the subgroup calculation, which are then used as the basis for further extensions. The next improvement that is covered is what is currently being termed as “Lumped Parameter MOC”. Because the subgroup calculation is a purely fixed source problem and multiple sweeps are performed only to update the boundary angular fluxes, the sweep procedure can be condensed to allow for the instantaneous propagation of the flux across a spatial domain, without the need to sweep along all segments in a ray. Once the boundary angular fluxes are considered to be converged, an additional sweep that will tally the scalar flux is completed. The last improvement that is investigated is the possible reduction of the number of azimuthal angles per octant in the shielding sweep. Typically 16 azimuthal angles per octant are used for self-shielding and eigenvalue calculations, but it is possible that the self-shielding sweeps are less sensitive to the number of angles than the full eigenvalue calculation.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗