Engineering topics
Stinville, Jean-Charles
Publications and source records attributed to Stinville, Jean-Charles.
Slip localization behavior at triple junctions in nickel-base superalloys
Incipient slip localization in the vicinity of hundreds of grain boundary triple junctions (TJs) in a lightly deformed nickel-base superalloy IN718 is studied using a combination of three-dimensional (3D) crystal plasticity finite element (CPFE) modeling, high resolution digital image correlation (HR-DIC) and 3D electron back-scatter diffraction tomography (3D EBSD). A 3D reconstruction method enables identification of thousands of TJs and correspondence of any observed slip bands with their originating TJ lines below the specimen surface. Here, we present a large-scale CPFE model of the experimental 3D microstructure composed of high-fidelity representation of the TJ lines and the boundaries and interiors of the parent grains and use it to calculate the local micromechanical response and slip activity of all TJs at the onset of macroscopic yielding. Statistical analysis of the calculated quantities reveal TJs develop larger stress concentration and grain-average re-orientation than grain interiors and grain boundaries, however no substantial differences in cumulative slip were found among these microstructural regions. We find that TJs with observed slip bands generate lower grain-average re-orientation, fewer active slip systems, and more localized slip on a single system than those without. The distinctions in the reorientation and slip activity are stronger in TJs that experience more intense slip.
Development of grain-scale slip activity and lattice rotation fields in Inconel 718
Using a combination of in-situ high-resolution digital image correlation (HR-DIC), Heaviside-DIC method (H-DIC), and crystal plasticity finite element (CPFE), we investigate the evolution of intragranular lattice rotations and slip activity during monotonic and cyclic loading in a high performance, polycrystalline face centered cubic material. The CPFE employs a quasi-3D model microstructure, which is a highly resolved mirror representation of the experimental in-situ test sample. In agreement, the measurements and calculations reveal that most grains, regardless of their size and lattice orientation, develop intragranular lattice rotation gradients that span the grain. For a small cluster of grains on the deformed material, we perform HR-DIC analysis of slip lines to demonstrate agreement in the active slip systems and changes in this local slip activity across the individual grains. The combined analysis reveals that deforming grains are divided into sub-granular regions of uniform lattice rotation and these regions are most often associated with only one or two active slip systems. The gradient lines that divide them correspond to changes in the predominant slip system. The model is used to examine the evolution of intragranular lattice rotation in a single fully reversed tension-compression cycle. The calculations indicate that intragranular gradients intensify during the reverse loading path as nearest neighboring regions appear to shed lattice rotation, increasing the lattice rotation in some regions, while shutting down rotation in neighboring regions. So these findings provide insight into the irreversible changes that develop within deforming grains at the scale of the grain, particularly the heterogeneous development of intragranular lattice rotation in early stages of deformation, which could serve as precursors to localization.
Crystallography and elastic anisotropy in fatigue crack nucleation at nickel alloy twin boundaries
Not provided.
Modeling lattice rotation fields from discrete crystallographic slip bands in superalloys
Here in this work, we investigate the relationship between an intense slip band (ISB) and the zone of large lattice rotations that forms ahead of the tip of the ISB. We develop a crystal plasticity finite element model of a discrete ISB lying within an oligocrystalline assembly and calculate the local crystalline stress and lattice rotation fields generated by the ISB. The calculations demonstrate that, first, a region of severe lattice rotations, commonly referred to as a microvolume, does not form without the ISB, and second, large amounts of accumulated slip in the ISB are required to enlarge the microvolume to sizes and rotation magnitudes observed experimentally. Ahead of the ISB tip, the quintessential plastic zone always forms, but the atypical microvolume forms when non-concentrated and spatially diffuse slip is activated by the ISB-induced stress field. This result suggests that the detrimental ISB/microvolume pair will likely appear in pairs of crystals in which transmission of the slip from the ISB is severely blocked by the grain boundary, a hypothesis that we verify with a few target cases.
Application of chord length distributions and principal component analysis for quantification and representation of diverse polycrystalline microstructures
Highlights: • Microstructure quantification based on directional chord length distribution and principal component analysis is presented • A boundary-based algorithm of calculations of chord length distributions is introduced • Utility of the quantification framework is shown in three case studies on synthetic, experimental, and simulation datasets • Angularly resolved chord length distribution captures essential details of grain size and shape in diverse microstructures • Low-dimensional representations of directional chord length distributions are obtained using principal component analysis - Abstract: Quantification of mesoscale microstructures of polycrystalline materials is important for a range of practical tasks of materials design and development. The current protocols of quantifying grain size and morphology often rely on microstructure metrics (e.g., mean grain diameter) that overlook important details of the mesostructure. In this work, we present a quantification framework based on directionally resolved chord length distribution and principal component analysis as a means of extracting additional information from 2-D microstructural maps. Towards this end, we first present in detail a method for calculating chord length distribution based on boundary segments available in modern digital datasets (e.g., from microscopy post-processing) and their low-rank representations by principal component analysis. The utility of the proposed framework for capturing grain size, morphology, and their anisotropy for efficient visualization, representation, and specification of polycrystalline microstructures is then demonstrated in case studies on datasets from synthetic generation, experiments (on Ni-base superalloys), and simulations (on steel during recrystallization).