Search NASA⌕ Search

Engineering topics

Stoltzfus, Brian S.

Publications and source records attributed to Stoltzfus, Brian S..

Model for the Solid–Liquid Interfacial Free Energy at High Pressures

The free energy involved in the formation of an interface between two phases (e.g., a solid–liquid interface) is referred to as the interfacial free energy. For the case of solidification, the interfacial free energy dictates the height of the energy barrier required to nucleate stable clusters of the newly forming solid phase and is essential for producing an accurate solidification kinetics model using classical nucleation theory (CNT)-based methods. While various methods have been proposed for modeling the interfacial free energy for solid–liquid interfaces in prior literature, many of these formulations involve making restrictive assumptions or approximations, such as the system being at or near equilibrium (i.e., the system temperature is approximately equal to the melt temperature) or that the system is at pressures close to atmospheric. However, these approximations and assumptions may break down in highly non-equilibrium situations, such as in dynamic-compression experiments where metastable liquids that are undercooled by hundreds of kelvin or over-pressurized by several gigapascals or more are formed before eventually solidifying. We derive a solid–liquid interfacial free-energy model for such high-pressure conditions by considering the enthalpies of interactions between pairs of atoms or molecules. We also consider the contribution of interface roughness (disordering) by incorporating a multilayer interface model known as the Temkin n-layer model. Our formulation is applicable to a diverse variety of materials, and we demonstrate it by developing models specifically for two different materials: water and gallium. We apply our interfacial free-energy formulation to CNT-based kinetics simulations of several suites of dynamic-compression experiments that cause liquid water to solidify to the high-pressure solid polymorph ice VII and have found good agreement to the observed kinetics with only minor empirical fitting.

36 MATERIALS SCIENCE↗

A compact x-ray diffraction system for dynamic compression experiments on pulsed-power generators

Pulsed-power generators can produce well-controlled continuous ramp compression of condensed matter for high-pressure equation-of-state studies using the magnetic loading technique. X-ray diffraction (XRD) data from dynamically compressed samples provide direct measurements of the elastic compression of the crystal lattice, onset of plastic flow, strength–strain rate dependence, structural phase transitions, and density of crystal defects, such as dislocations. Here, we present a cost-effective, compact, pulsed x-ray source for XRD measurements on pulsed-power-driven ramp-loaded samples. This combination of magnetically driven ramp compression of materials with a single, short-pulse XRD diagnostic will be a powerful capability for the dynamic materials’ community to investigate in situ dynamic phase transitions critical to equation of states. Finally, we present results using this new diagnostic to evaluate lattice compression in Zr and Al and to capture signatures of phase transitions in CdS.

47 OTHER INSTRUMENTATION↗

Scale and rate in CdS pressure-induced phase transition

Here, we describe recent efforts to improve our predictive modeling of rate-dependent behavior at, or near, a phase transition using molecular dynamics simulations. Cadmium sulfide (CdS) is a well-studied material that undergoes a solid-solid phase transition from wurtzite to rock salt structures between 3 and 9 GPa. Atomistic simulations are used to investigate the dominant transition mechanisms as a function of orientation, size and rate. We found that the final rock salt orientations were determined relative to the initial wurtzite orientation, and that these orientations were different for the two orientations and two pressure regimes studied. The CdS solid-solid phase transition is studied, for both a bulk single crystal and for polymer-encapsulated spherical nanoparticles of various sizes.

42 ENGINEERING↗

Variable-pulse-shape pulsed-power accelerator

A variable-pulse-shape pulsed-power accelerator is driven by a large number of independent LC drive circuits. Each LC circuit drives one or more coaxial transmission lines that deliver the circuit's output power to several water-insulated radial transmission lines that are connected in parallel at small radius by a water-insulated post-hole convolute. The accelerator can be impedance matched throughout. The coaxial transmission lines are sufficiently long to transit-time isolate the LC drive circuits from the water-insulated transmission lines, which allows each LC drive circuit to be operated without being affected by the other circuits. This enables the creation of any power pulse that can be mathematically described as a time-shifted linear combination of the pulses of the individual LC drive circuits. Therefore, the output power of the convolute can provide a variable pulse shape to a load that can be used for magnetically driven, quasi-isentropic compression experiments and other applications.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Field-Distortion Air-Insulated Switches for Next-Generation Pulsed-Power Accelerators

We have developed two advanced designs of a field-distortion air-insulated spark-gap switch that reduce the size of a linear-transformer-driver (LTD) brick. Both designs operate at 200 kV and a peak current of ~50 kA. At these parameters, both achieve a jitter of less than 2 ns and a prefire rate of ~0.1% over 5000 shots. We have reduced the number of switch parts and assembly steps, which has resulted in a more uniform, design-driven assembly process. We will characterize the performance of tungsten-copper and graphite electrodes, and two different electrode geometries. The new switch designs will substantially improve the electrical and operational performance of next-generation pulsed-power accelerators.

36 MATERIALS SCIENCE↗

Optimization of Isentropic Compression Loads on Current-Adder Pulsed Power Accelerator Architectures

The Thor pulsed power generator is being developed at Sandia National Laboratories. The design consists of up to 288 decoupled and transit time isolated capacitor-switch units, called “bricks”, that can be individually triggered to achieve a high degree of pulse tailoring for magnetically-driven isentropic compression experiments (ICE). The connecting transmission lines are impedance matched to the bricks, allowing the capacitor energy to be efficiently delivered to an ICE strip-line load with peak pressures of over 100 GPa. Thor will drive experiments to explore equation of state, material strength, and phase transition properties of a wide variety of materials. We present an optimization process for producing tailored current pulses, a requirement for many material studies, on the Thor generator. This technique, which is unique to the novel “current-adder” architecture used by Thor, entirely avoids the iterative use of complex circuit models to converge to the desired electrical pulse. We describe the optimization procedure for the Thor design and show results for various materials of interest. Also, we discuss the extension of these concepts to the megajoule-class Neptune machine design. Given this design, we are able to design shockless ramp-driven experiments in the 1 TPa range of material pressure.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Creating the Foundation of Next Generation Pulsed-Power Accelerator Technology

This SAND report covers the work performed under the "Creating the foundation of next-generation pulsed-power-accelerator technology" LDRD. This foundation consists of both foundational concepts and foundational components. Advances were made at both levels, with new machine concepts such as Thor and new machine components such has arc quenching charge resistors, laying a new foundation for pulsed power work at Sandia. This report attempts to summarize the numerous advances made at both of these levels under this LDRD over the last three years.

43 PARTICLE ACCELERATORS↗

Millimeter-Gap Magnetically Insulated Transmission Line Power Flow Experiments

An experiment platform has been designed to study vacuum power flow in magnetically insulated transmission lines (MITLs). The platform was driven by the 400-GW Mykonos-V accelerator. The experiments conducted quantify the current loss in a millimeter-gap MITL with respect to vacuum conditions in the MITL for two different gap distances, 1.0 and 1.3 mm. The current loss for each gap was measured for three different vacuum pump down times. As a ride along experiment, multiple shots were conducted with each set of hardware to determine if there was a conditioning effect to increase current delivery on subsequent shots. The experiment results revealed large differences in performance for the 1.0 and 1.3 mm gaps. The 1.0 mm gap resulted in current loss of 40%-60% of peak current. The 1.3 mm gap resulted in current losses of less than 5% of peak current. Classical MITL models that neglect plasma expansion predict that there should be zero current loss, after magnetic insulation is established, for both of these gaps. The experiments result s indicate that the vacuum pressure or pump down time did not have a significant effect on the measured current loss at vacuum pressures between 1e-4 and 1e-5 Torr. Additionally, there was not repeatable evidence of a conditioning effect that reduced current loss for subsequent full-energy shots on a given set of hardware. It should be noted that the experiments conducted likely did not have large loss contributions due to ion emission from the anode due to the relatively small current densi-ties (25-40 kA/cm) in the MITL that limited the anode temperature rise due to ohmic heating. The results and conclusions from these experiments may have limited applicability to MITLs of high current density (>400 kA/cm) used in the convolute and load region of the Z which experience temperature increases of >400° C and generate ion emission from anode surfaces.

42 ENGINEERING↗

High reliability low jitter pulse generator

A method and concomitant apparatus for generating pulses comprising providing a laser light source, disposing a voltage electrode between ground electrodes, generating laser sparks using the laser light source via laser spark gaps between the voltage electrode and the ground electrodes, and outputting pulses via one or more insulated ground connectors connected to the voltage electrode.

47 OTHER INSTRUMENTATION↗