Engineering topics

Stouffer, D. C.

Publications and source records attributed to Stouffer, D. C..

13 records

NASA NTRS1991

A constitutive model for the high temperature inelastic response of nickel base superalloys

The objective of this research is to develop a constitutive equation for the uniaxial and multiaxial fatigue response of Rene 80 between the temperatures of 538 C and 982 C. The constitutive equation is accompanied by an experimental program for the evaluation of the material constants and extensive verification through the successful prediction of mechanical cycling experiments. These results include the prediction of the high temperature multiaxial response of Rene 80 that includes torsion and proportional and non-proportional loading histories.

Stouffer, D. C.↗

NASA NTRS1990

A constitutive model for the inelastic multiaxial response of Rene 80 at 871 C and 982 C

This paper contains an extension of the uniaxial state variable constitutive model of Ramaswamy et al. (1988) to the case of multiaxial loading. The correlation between uniaxial and multiaxial loading conditions is achieved through the assumptions of material isotropy and conservation of inelastic volume. The multiaxial extension is based only on the material parameters evaluated from uniaxial loading. The research is accompanied by a multiaxial experimental program to evaluate the response of Rene 80 at 871 C and 982 C. Experiments in the program include torsion, proportional axial and torsion, and nonproportional loading. It was shown experimentally that there is no extra hardening from the multiaxial loading than results from uniaxial loading. Further, it is shown that the multiaxial model is successful in predicting the experimental results using only the parameters determined from the uniaxial experiments.

Stouffer, D. C.↗

NASA NTRS1990

A crystallographic model for the tensile and fatigue response for Rene N4 at 982 C

An anisotropic constitutive model based on crystallographic slip theory was formulated for nickel-base single-crystal superalloys. The current equations include both drag stress and back stress state variables to model the local inelastic flow. Specially designed experiments have been conducted to evaluate the existence of back stress in single crystals. The results showed that the back stress effect of reverse inelastic flow on the unloading stress is orientation-dependent, and a back stress state variable in the inelastic flow equation is necessary for predicting inelastic behavior. Model correlations and predictions of experimental data are presented for the single crystal superalloy Rene N4 at 982 C.

Sheh, M. Y.↗

NASA NTRS1988

A crystallographic model for nickel base single crystal alloys

The purpose of this research is to develop a tool for the mechanical analysis of nickel-base single-crystal superalloys, specifically Rene N4, used in gas turbine engine components. This objective is achieved by developing a rate-dependent anisotropic constitutive model and implementing it in a nonlinear three-dimensional finite-element code. The constitutive model is developed from metallurgical concepts utilizing a crystallographic approach. An extension of Schmid's law is combined with the Bodner-Partom equations to model the inelastic tension/compression asymmetry and orientation-dependence in octahedral slip. Schmid's law is used to approximate the inelastic response of the material in cube slip. The constitutive equations model the tensile behavior, creep response and strain-rate sensitivity of the single-crystal superalloys. Methods for deriving the material constants from standard tests are also discussed. The model is implemented in a finite-element code, and the computed and experimental results are compared for several orientations and loading conditions.

Dame, L. T.↗

NASA NTRS1988

Development of a unified constitutive model for an isotropic nickel base superalloy Rene 80

Accurate analysis of stress-strain behavior is of critical importance in the evaluation of life capabilities of hot section turbine engine components such as turbine blades and vanes. The constitutive equations used in the finite element analysis of such components must be capable of modeling a variety of complex behavior exhibited at high temperatures by cast superalloys. The classical separation of plasticity and creep employed in most of the finite element codes in use today is known to be deficient in modeling elevated temperature time dependent phenomena. Rate dependent, unified constitutive theories can overcome many of these difficulties. A new unified constitutive theory was developed to model the high temperature, time dependent behavior of Rene' 80 which is a cast turbine blade and vane nickel base superalloy. Considerations in model development included the cyclic softening behavior of Rene' 80, rate independence at lower temperatures and the development of a new model for static recovery.

Ramaswamy, V. G.↗

NASA NTRS1988

A constitutive model with damage for high temperature superalloys

A unified constitutive model is searched for that is applicable for high temperature superalloys used in modern gas turbines. Two unified inelastic state variable constitutive models were evaluated for use with the damage parameter proposed by Kachanov. The first is a model (Bodner, Partom) in which hardening is modeled through the use of a single state variable that is similar to drag stress. The other (Ramaswamy) employs both a drag stress and back stress. The extension was successful for predicting the tensile, creep, fatigue, torsional and nonproportional response of Rene' 80 at several temperatures. In both formulations, a cumulative damage parameter is introduced to model the changes in material properties due to the formation of microcracks and microvoids that ultimately produce a macroscopic crack. A back stress/drag stress/damage model was evaluated for Rene' 95 at 1200 F and is shown to predict the tensile, creep, and cyclic loading responses reasonably well.

Sherwood, J. A.↗

NASA NTRS1988

Anisotropic constitutive modeling for nickel base single crystal superalloys using a crystallographic approach

A micromechanical model based on crystallographic slip theory was formulated for nickel-base single crystal superalloys. The current equations include both drag stress and back stress state variables to model the local inelastic flow. Specially designed experiments have been conducted to evaluate the effect of back stress in single crystals. The results showed that (1) the back stress is orientation dependent; and (2) the back stress state variable in the inelastic flow equation is necessary for predicting anelastic behavior of the material. The model also demonstrated improved fatigue predictive capability. Model predictions and experimental data are presented for single crystal superalloy Rene N4 at 982 C.

Stouffer, D. C.↗

NASA NTRS1987

Anisotropic constitutive modeling for nickel base single crystal superalloy Rene N4 at 982 C

A back stress/drag stress constitutive model based on a crystallographic approach to model single crystal anisotropy is presented. Experimental results demonstrated the need for the back stress variable in the inelastic flow equations. Experimental findings suggested that back stress is orientation dependent and controls both strain hardening and recovery characteristics. Due to the observed stable fatigue loops at 1800 F, drag stress is considered constant for this temperature. The constitutive model operated with constraints determined only from tensile data was extensively tested from simple tensile and fatigue to complicated strain hold tests. The model predicted very well under those conditions.

Stouffer, D. C.↗

NASA NTRS1986

Constitutive modeling for single crystal superalloys

The inelastic response of single crystal gamma/gamma prime superalloys is quite different from the behavior of polycrystalline nickel base superalloys. Upto a critical temperature the yield stress of single crystal alloys is a function of the material orientation relative to the direction of the applied stress and the material exhibits significant tension/compression asymmetry. This behavior is primarily due to slip on the octahedral slip system. Above the critical temperature there is a sharp drop in the yield stress, cube slip becomes more predominant and the tension/compression asymmetry is reduced. Similar orientation and tension/compression asymmetry is observed in creep and secondary creep above the critical temperature is inferred to occur by octahedral slip. There are two exceptions to this behavior. First, loading near the (111) orientation exhibits cube slip at all temperatures, and; second, loading near the (001) orientation produces only octahedral slip at all temperatures. The constitutive model is based on separating the total global strain into elastic and inelastic components. This model is developed and briefly discussed.

Stouffer, D. C.↗

NASA NTRS1986

Anisotropic constitutive model for nickel base single crystal alloys: Development and finite element implementation

A tool for the mechanical analysis of nickel base single crystal superalloys, specifically Rene N4, used in gas turbine engine components is developed. This is achieved by a rate dependent anisotropic constitutive model implemented in a nonlinear three dimensional finite element code. The constitutive model is developed from metallurigical concepts utilizing a crystallographic approach. A non Schmid's law formulation is used to model the tension/compression asymmetry and orientation dependence in octahedral slip. Schmid's law is a good approximation to the inelastic response of the material in cube slip. The constitutive equations model the tensile behavior, creep response, and strain rate sensitivity of these alloys. Methods for deriving the material constants from standard tests are presented. The finite element implementation utilizes an initial strain method and twenty noded isoparametric solid elements. The ability to model piecewise linear load histories is included in the finite element code. The constitutive equations are accurately and economically integrated using a second order Adams-Moulton predictor-corrector method with a dynamic time incrementing procedure. Computed results from the finite element code are compared with experimental data for tensile, creep and cyclic tests at 760 deg C. The strain rate sensitivity and stress relaxation capabilities of the model are evaluated.

Dame, L. T.↗

NASA NTRS1985

Finite element analysis of notch behavior using a state variable constitutive equation

The state variable constitutive equation of Bodner and Partom was used to calculate the load-strain response of Inconel 718 at 649 C in the root of a notch. The constitutive equation was used with the Bodner-Partom evolution equation and with a second evolution equation that was derived from a potential function of the stress and state variable. Data used in determining constants for the constitutive models was from one-dimensional smooth bar tests. The response was calculated for a plane stress condition at the root of the notch with a finite element code using constant strain triangular elements. Results from both evolution equations compared favorably with the observed experimental response. The accuracy and efficiency of the finite element calculations also compared favorably to existing methods.

Dame, L. T.↗

NASA NTRS1984

Constitutive modeling of inelastic anisotropic material response

A constitutive equation was developed to predict the inelastic thermomechanical response of single crystal turbine blades. These equations are essential for developing accurate finite element models of hot section components and contribute significantly to the understanding and prediction of crack initiation and propagation. The method used was limited to unified state variable constitutive equations. Two approaches to developing an anisotropic constitutive equation were reviewed. One approach was to apply the Stouffer-Bodner representation for deformation induced anisotropy to materials with an initial anisotropy such as single crystals. The second approach was to determine the global inelastic strain rate from the contribution of the slip in each of the possible crystallographic slip systems. A three dimensional finite element is being developed with a variable constitutive equation link that can be used for constitutive equation development and to predict the response of an experiment using the actual specimen geometry and loading conditions.

Stouffer, D. C.↗

NASA NTRS1983

A Potential Function Derivation of a Constitutive Equation for Inelastic Material Response

Physical and thermodynamic concepts are used to develop a potential function for application to high temperature polycrystalline material response. Inherent in the formulation is a differential relationship between the potential function and constitutive equation in terms of the state variables. Integration of the differential relationship produces a state variable evolution equation that requires specification of the initial value of the state variable and its time derivative. It is shown that the initial loading rate, which is directly related to the initial hardening rate, can significantly influence subsequent material response. This effect is consistent with observed material behavior on the macroscopic and microscopic levels, and may explain the wide scatter in response often found in creep testing.

Stouffer, D. C.↗