Engineering topics

Strange, Lyndi E.

Publications and source records attributed to Strange, Lyndi E..

9 records

DOE OSTI2024

Electrochemical Oxidation of Seawater for Renewable Energy Generation and Storage in Coastal Areas

In this work, we demonstrated how the Clean Sustainable Electrochemical Treatment process can be used to process seawater while simultaneously generating molecular hydrogen. The specific goal of this project is to (1) demonstrate selective removal of chemical oxygen demand over the oxygen and chlorine evolution reactions, (2) optimize electrode composition to improve electrochemical performance, and (3) demonstrate long-term (>100 h) stability experiments.

08 HYDROGEN↗

DOE OSTI2024

In-house synthesized poly(ether ether ketone) ionenes. I. ToF-SIMS spectra in the positive ion mode

Static time-of-flight secondary ion mass spectrometry (ToF-SIMS) was performed for acquiring the high-resolution surface spectra of four types of synthesized imidazolium ionene membranes. These novel membranes have aromatic ether–ketone–ether linkages inspired by poly(ether ether ketone) (PEEK). The PEEK-ionenes synthesized for this study have imidazolium cations placed in the polymeric backbone with bistriflimide [Tf 2 N]- counterions. The attention given to synthetically modified PEEK derivatives, such as PEEK-ionenes, is considerable due to their ability to selectively capture CO 2 molecules and other light gases. Therefore, it is important to characterize the surface of these synthesized novel PEEK-ionenes. In this work, characteristic and unique peaks were identified in the positive spectra of each sample. The differences in mass spectra among the samples provide insights for optimizing or fine-tuning the PEEK-ionenes synthesis to achieve a high-performance CO 2 separation membrane with enhanced permeability, selectivity, and mechanical stability. The SIMS spectra and identified characteristic peaks of these synthesized ionenes will serve as a reference in the positive mode, complementing the corresponding spectra reported in the negative ion mode (Paper II).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2023

Low-Temperature Electrochemical Wastewater Oxidation

Here, we demonstrated the Clean Sustainable Electrochemical Treatment (CleanSET) process that enables the distributed clean-up of biomass-derived wastewater while simultaneously generating hydrogen (H 2 ). The specific goal of this project is to 1) demonstrate the selective removal of chemical oxygen demand (COD), total carbon (TC), and total nitrogen (TN) of different wastewaters, 2) optimize the electrode composition to improve electrochemical performance, and 3) perform a high-level techno-economic analysis to obtain levelized costs of disposal (LCOD) .

08 HYDROGEN↗

DOE OSTI2023

Probing corrosion using a simple and versatile in situ multimodal corrosion measurement system

In this work, we have developed a unique in situ multimodal corrosion system that is capable of acquiring electrochemical data, sample imaging/visualization and hydrogen collection, simultaneously. Each of these modalities yield valuable information pertaining to the ongoing corrosion process. Combining them can yield holistic information on the role of microstructure, processing history, presence of coatings, etc., on the sequence of steps occurring during the corrosion process, and how they correlate with the acquired electrochemical data. Four materials systems, namely AA6061-T6 aluminum alloy, AZ91 magnesium alloy, galvanized DP590 steel, and pure Zn, were investigated under open circuit potential and under potentiodynamic polarization. The multimodal corrosion system was utilized to observe processes such as surface passivation and dissolution, pit and filiform corrosion initiation and propagation, and was correlated with location and magnitude of hydrogen evolution. This approach is shown to yield a truly multimodal understanding of the ongoing corrosion processes.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Chapter 14: Surface plasmon resonance enhanced artificial photosynthesis of chemical fuels for energy storage

Nanostructured noble metals such as Au, Ag, and Cu have interesting optical properties because of the oscillation motions of their surface electrons upon strong coupling with light under resonance conditions. This resonant oscillation motion of conduction electrons refers to surface plasmon resonance (SPR) and localized SPR (LSPR) when localized near the surface of a nanoparticle. The extinction spectrum of a solution of plasmonic nanoparticles has tunable wavelength responses from UV to NIR due to strong light scattering and absorption which are highly sensitive to the permittivity of the nanoparticles, their sizes and shapes, and chemical environment. Strong light scattering due to the LSPR of plasmonic nanoparticles creates a strong localized and far-field intensity capable of enhancing light absorption characteristics of a chromophore near a plasmonic surface. Engineering the chromophores’ radiative decay dynamics can be done by 1) increasing its radiative decay rate to increase its photoluminescence intensity and 2) increasing its nonradiative decay rates associated to direct charge transfer to the metal surface. Such interesting photophysical properties of a chromophore can be extended to other light-absorbing materials such as semiconductor thin films and nanostructures. This plasmonic effect on the photophysics of a light-absorbing material can be theoretically and experimentally validated. The phenomenon has also been applied to advanced optoelectronic devices such as organic light-emitting diodes (OLED)1 and organic photovoltaics (OPV).2-4 The local field created by the SPR can provide an intense EM field to enhance photoluminescence emission of an organic chromophore5-8 and Raman scattering of an organic molecule, and single-molecule Raman9-10 can be detected on specially designed LSPR substrate. (Figure 1 on SPR for energy) Recent studies suggest that LSPR can be incorporated in light-harvesting and conversion systems to increase energy conversion in a solar cell and photoelectrochemical cell and chemical transformations of CO2 to chemical fuels.11-12 Plasmonic active metals naturally exhibit catalytic activities for electrochemical fuel conversion that can be enhanced by engineering their structures to form unique catalytic structures such as symmetry-broken Au-Cu Janus nanocrystals.13 These studies are critical to addressing the global challenges of energy14-15 and CO2 emission from nonrenewable sources such as coal, petroleum, and natural gas.16-17 Electrochemical systems comprised of unique photonic structures and functions that enable efficient and affordable energy harvesting/conversion/storage are highly desired for providing safe and environment-friendly energy sources. This chapter reviews our recent work of LSPR enabled photoelectrochemical water splitting and recent advances in LSPR-enabled CO2 reduction and photochemical reactions reported in the literature. Scientific and technical challenges of applying LSPR to enhance these energy conversion and storage systems are discussed at the conclusion of this chapter.

Pan, Shanlin↗

DOE OSTI2023

Surface analysis insight note: X‐ray photoelectron spectroscopy analysis of battery electrodes—Challenges with nickel–manganese–cobalt and Li examples using an Al Kα x‐ray source

X‐ray photoelectron spectroscopy (XPS) has become a highly important tool for the analysis of battery materials and components. However, both anecdotal and detailed analysis of selected parts of the literature indicate that many reports of XPS on battery electrodes have significant analysis or data flaws. In this paper, we highlight several of the common challenges that analysts face when using XPS for battery materials, pointing to recent literature that addresses many of the critical issues associated with sample preparation as well as data collection and analysis. A common error for battery materials (and other materials) involves ignoring peak overlaps and interferences. Specifically, when a “minor” peak associated with a component in relatively high concentration overlaps or contributes to the primary peak (or one recommended for quantitative analysis) from a different element in the material. Overlap issues apply to many battery electrodes composed of many elements with complex photoelectron peak structures, as well as those involving peaks with seemingly simpler spectral envelopes such as Li and F. Examples of issues associated with battery systems are highlighted by a discussion of challenges associated with XPS analysis of Li and nickel–manganese–cobalt (NMC) electrodes in battery systems. Lithium analysis has challenges associated with the preparation and an often‐unrecognized peak overlap with F. In our laboratory and in the literature, NMC electrodes are often examined and new XPS users do not always recognize interference of the Auger signal from F KLL (in or on the electrode) with Ni 2p photoelectron spectrum when generated with Al Kα X‐rays. The use of simulated spectra involving both F and NiO demonstrates the extent of F Auger contributions to the Ni 2p signal strength as a function of the F/Ni atom ratio in the material and suggests spectra information that can be used to identify how significant effects will be on the resultant spectra. Our analysis demonstrates that in many cases overlap issues are significant for real electrode materials.

25 ENERGY STORAGE↗

DOE OSTI2022

Li 7 P 2 S 8 Br 0.5 I 0.5 (LPSBI) solid state electrolyte by XPS

There have been increasing surface characterization studies of battery materials specifically in the context of before and after cell operation to determine any chemical changes. Therefore, providing reliable reference spectra of battery-related materials is important. In this paper, survey and high-energy resolution data are reported for the solid-state electrolyte Li 7 P 2 S 8 Br 0.5 I 0.5 (LPSBI), which has been synthesized and characterized at Pacific Northwest National Laboratory. The current data presents narrow scan regions of I 3d, I 4d, Br 3d, O 1s, P 2p, S 2p, and C 1s core level spectra as well as wide-scan survey data that was obtained using Al K a x-ray source with a Thermo Fisher Nexsa instrument.

25 ENERGY STORAGE↗

DOE OSTI2022

Multimodal analysis and characterization of the boehmite layer formed on AA6061 before and after alkaline etching

Low-enriched uranium (LEU) alloyed with 10% Mo (U-10Mo) is being considered as a promising alternative to oxide-based dispersion fuel with high-enriched uranium for use in research reactors. The configuration of this proposed LEU monolithic LEU fuel plate consists of a U-10Mo plate-type fuel foil with a 25 µm zirconium interlayer barrier clad with an aluminum alloy (AA6061). In certain research reactors, the clad AA6061 is coated with a boehmite layer to prevent corrosion. The boehmite layer has a high-pH passivation range, which makes it resistant to oxidation. Boehmite is usually formed on the AA6061 surface by autoclave processing. Before the boehmite layer is added, the surface of the AA6061 is cleaned using techniques such as polishing and wet etching. In this study, we use multimodal analysis to examine how pretreatment of AA6061 using polishing followed by alkaline etching affects the chemical composition of the boehmite layer. X-ray photoelectron microscopy (XPS), transmission electron microscopy (TEM), and x-ray diffraction (XRD) were used to study the chemical changes in the boehmite layer caused by alkaline etching pretreatment. XPS provides quantitative analysis for the Al:O ratio as well as oxidation states present on the surface, which suggests slight oxidation of the boehmite surface after alkaline etching of the AA6061 surface. We further explored this suggested oxidation of the boehmite surface using high-resolution transmission electron microscopy with selected area electron diffraction (SAED) and grazing incidence x-ray diffraction (GI-XRD), which suggested only a small amount of aluminum oxide at the surface. The multimodal analysis and imaging yielded new insights for optimizing boehmite growth on AA6061 for research reactors.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Studying Corrosion Using Miniaturized Particle Attached Working Electrodes and the Nafion Membrane

We developed a new approach to attach particles onto a conductive layer as a working electrode (WE) in a microfluidic electrochemical cell with three electrodes. Nafion, an efficient proton transfer molecule, is used to form a thin protection layer to secure particle electrodes. Spin coating is used to develop a thin and even layer of Nafion membrane. The effects of Nafion (5 wt% 20 wt%) and spinning rates were evaluated using multiple sets of replicates. The electrochemical performance of various devices was demonstrated. Additionally, the electrochemical performance of the devices is used to select and optimize fabrication conditions. The results show that a higher spinning rate and a lower Nafion concentration (5 wt%) induce a better performance, using cerium oxide (CeO2) particles as a testing model. The WE surfaces were characterized using atomic force microscopy (AFM), scanning electron microscopy-focused ion beam (SEM-FIB), time-of-flight secondary ion mass spectrometry (ToF-SIMS), and X-ray photoelectron spectroscopy (XPS). The comparison between the pristine and corroded WE surfaces shows that Nafion is redistributed after potential is applied. Our results verify that Nafion membrane offers a reliable means to secure particles onto electrodes. Furthermore, the electrochemical performance is reliable and reproducible. Thus, this approach provides a new way to study more complex and challenging particles, such as uranium oxide, in the future.

42 ENGINEERING↗