Engineering topics
Publications and source records attributed to Stroud, C. W..
Transient response of thermal-protection material to heat applied to surface calculated using CHAP III computer program. Used to analyze chemical kinetics of pyrolysis gas in detail and examine pyrolysis reactions-in-depth. Analysis includes deposition of solid products produced by chemical reactions in gas phase. Uses modeling technique that approximates wide range of ablation problems. CHAP III written in FORTRAN IV.
A computer program has been written to provide an interface between the HP Series 200 desktop computers, operating under HP Standard Pascal 3.0, and the HP2250 Data Acquisition and Control System. Pascal 3.0 for the HP9000 desktop computer gives a number of procedures for handling bus communication at various levels. It is necessary, however, to reach the lowest possible level in Pascal to handle the bus protocols required by the HP2250. This makes programming extremely complex since these protocols are not documented. The program described solves those problems and allows the user to immediately program, simply and efficiently, any measurement and control language (MCL/50) application with a few procedure calls. The complete set of procedures is available on a 5 1/4 inch diskette from Cosmic. Included in this group of procedures is an Exerciser which allows the user to exercise his HP2250 interactively. The exerciser operates in a fashion similar to the Series 200 operating system programs, but is adapted to the requirements of the HP2250. The programs on the diskette and the user's manual assume the user is acquainted with both the MCL/50 programming language and HP Standard Pascal 3.0 for the HP series 200 desktop computers.
Oxidation and embrittlement are concerns in use of titanium foils for shielding advanced space transportation system vehicles during earth reentry. Ti-6Al-4V in 0.003 in. and 0.035 in. thicknesses were exposed to multiple cycles of simulated space transportation system ascent/reentry conditions at temperatures ranging from 1000 F to 1200 F. Residual mechanical tests and metallurgical analyses were made on the specimens after exposure. Results show that tensile elongation is the mechanical property most affected by the reentry environment. Results are presented to show a comparison of residual properties of foil specimens from static oxidation exposure and cyclic oxidation exposure.
Coated, reinforced carbon-carbon (RCC) is used for the leading edges of the Space Shuttle. The mass loss characteristics of RCC specimens coated with tetra-ethyl-ortho-silicate (TEOS) were determined for conditions which simulated the entry environment expected at the stagnation area of the wing leading edge. Maximum specimen temperature was 1632 K. Specimens were exposed for up to 100 missions. Stress levels up to 8.274 MPa caused an average increase in oxidation of 6 percent over unstressed specimens. Experimentally determined mass losses were compared with those predicted by an existing empirical analysis.
Coated, reinforced carbon-carbon (RCC) is used for the leading edges of the space shuttle. The mass loss characteristics of RCC specimens coated with tetraethyl orthosilicate (TEOS) were determine for conditions which simulated the environment expected at the lug attachment area of the leading edge. Mission simulation included simultaneous application of load, temperature, and oxygen partial pressure. Maximum specimen temperature was 900 K (1160 F). Specimens were exposed for up to 80 simulated missions. Stress levels up to 6.8 MPa (980 psi) did not significantly affect the mass loss characteristics of the TEOS-coated RCC material. Mass loss was correlated with the bulk density of the specimens.
Equilibrium is determined by finding chemical composition with minimum free energy. Method of steepest descent is applied to quadratic representation of free-energy surface. Solution is initiated by selecting arbitrary set of mole fractions, from which point on free-energy surface is computed.
A computer program is described that will compute the transient response of a thermal protection material to a prescribed heat input at the surface. The program has the capability of analyzing pyrolysis gas chemical kinetics in detail and treating pyrolysis reactions-in-depth. Deposition of solid products produced by chemical reactions in the gas phase is included in the analysis. An outline is given for the theory. detailed operating instructions for the computer program are included.
Chemical equilibrium of ablation materials including condensed species
Effect of chemical properties of pyrolysis gases on heat shield mass required for lifting reentry vehicle in typical reentry trajectory
Chemical reaction-plane approximation in ablation analyses
Numerical method for reducing data from thick calorimeter to determine heating rate to calorimeter surface
Approximate solution of ablation of reinforced plastic for heat protection
Analytical determination of thermoconductivity of honeycomb-core panels fabricated from cobalt-base alloy
Several different types of insulating heat shields have been subjected to aerodynamic tests and radiant-heating tests in order to obtain a better insight into the problems involved when the primary structure of m aerodynamically heated vehicle is substantially cooler than the exposed external surface. One of the main problems was considered to be a proper allowance for thermal expansion caused by these large temperature differences, so that undue distortion or thermal stresses would not occur in either the outer shield or the underlying structure. corrugated outer skin with suitably designed expansion joints was a feature of all the specimens tested.
Explore the source record for details and available documents.