Engineering topics

Strozzi, David J.

Publications and source records attributed to Strozzi, David J..

4 records

DOE OSTI2023

First large capsule implosions in a frustum-shaped hohlraum

Here, we report on the first indirect-drive implosions driven by a dual conical frustum-shaped hohlraum denoted “frustraum” and the experimental tuning campaigns leading up to two layered implosions. The campaign used 1.2 and 1.4 mm inner radius high density carbon (HDC) capsules and represented the largest HDC capsules to be imploded on the National Ignition Facility via indirect drive. Several techniques were successfully implemented to control the Legendre mode 2 capsule symmetry of the implosions, including changing the wall angle of the frustraum, which is not possible with cylindrical hohlraums. A mode 4 feature was observed and its implications for hotspot mix discussed. Two layered implosions were conducted with 1.2 mm inner radius capsules, the latter of which achieved the highest layered capsule absorbed energy on the National Ignition Facility using only 1.74 MJ of laser energy. The layered implosion results, along with generalized Lawson parameters, suggest that increasing the energy absorbed by the capsule at the expense of long coast times makes it more challenging to achieve ignition and that further reducing coast time (time between end of laser pulse and bang time) closer to the 1 ns level is warranted to improve the areal density and make it easier to achieve the hotspot temperature, alpha heating, and yield amplification required for ignition.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2023

Performance scaling with an applied magnetic field in indirect-drive inertial confinement fusion implosions

Magnetizing a cryogenic deuterium–tritium (DT)-layered inertial confinement fusion (ICF) implosion can improve performance by reducing thermal conduction and improving DT-alpha confinement in the hot spot. A room-temperature, magnetized indirect-drive ICF platform at the National Ignition Facility has been developed, using a high-Z, high-resistivity AuTa 4 alloy as the hohlraum wall material. Experiments show a 2.5× increase in deuterium–deuterium (DD) neutron yield and a 0.8-keV increase in hot-spot temperature with the application of a 12-T B-field. Further, for an initial 26-T B-field, we observed a 2.9× yield increase and a 1.1-keV temperature increase, with the inferred burn-averaged B-field in the compressed hot spot estimated to be 7.1 ± 1.8 kT using measured primary DD-n and secondary DT-n neutron yields.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2022

Exploring implosion designs for increased compression on the National Ignition Facility using high density carbon ablators

It has long been recognized that high compression, and hence good confinement, is essential to achieving high yields in inertial confinement fusion implosions. In pursuit of multi-megajoule yields on the National Ignition Facility (NIF), a new campaign has begun aimed at testing the hypothesis that controlling hydrodynamic stability is key to achieving effective higher compression with the high density carbon ablators currently fielded on NIF. This campaign is built around a new implosion design, called SQ-n, that is derived from the uniquely stable Bigfoot design tested on NIF in 2016–2019. While very stable and with performance that was quite close to one-dimensional expectations, Bigfoot was a relatively high adiabat, and consequently lower compression design. The goal of SQ-n is then to evolve Bigfoot toward a higher compression design but without compromising its unique stability characteristics. Specifically, SQ-n adopts a ramped foot pulse shape to minimize early time Richtmyer–Meshkov instability growth and uses an ablator dopant distribution extending all of the way to the fuel–ablator interface that simulations suggest further reduces perturbation growth. In conclusion, this paper describes the design philosophy pursued with SQ-n, the results of instability modeling of the candidate design, and the experimental campaign planned to test these ideas in the near future.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2022

Magnetized laser–plasma interactions in high-energy-density systems: Parallel propagation

In this study, we investigate parametric processes in magnetized plasmas, driven by a large-amplitude pump light wave. Our focus is on laser–plasma interactions relevant to high-energy-density (HED) systems, such as the National Ignition Facility and the Sandia MagLIF concept. We present a self-contained derivation of a “parametric” dispersion relation for magnetized three-wave interactions, meaning the pump wave is included in the equilibrium, similar to the unmagnetized work of Drake et al., Phys. Fluids 17, 778 (1974). For this, we use a multi-species plasma fluid model and Maxwell's equations. The application of an external B field causes right- and left-polarized light waves to propagate with differing phase velocities. This leads to Faraday rotation of the polarization, which can be significant in HED conditions. Phase-matching and linear wave dispersion relations show that Raman and Brillouin scattering have modified spectra due to the background B field, though this effect is usually small in systems of current practical interest. We study a scattering process we call stimulated whistler scattering, where a light wave decays to an electromagnetic whistler wave (ω≲ω ce ) and a Langmuir wave. This only occurs in the presence of an external B field, which is required for the whistler wave to exist.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗