ART-GCR overview Strydom Day 1
ART-GCR Program Elements PowerPoint Presentation
Engineering topics
Publications and source records attributed to Strydom, Gerhard.
ART-GCR Program Elements PowerPoint Presentation
ART-GCR “Methods” activity is split between Experimental Validation data from the ANL NSTF and OSU HTTF (next three presentations). HTGR core simulation (this presentation). International collaboration within OECD Generation-IV (Gen-IV) and USA/Japan bi-lateral agreements (this presentation) HTGR Simulation Methods No new NE-52 funding for HTGR Methods support in FY20; ~$200K FY19 carry-over funds only. Consists of international code-to-code benchmarks (IAEA CRP on HTGR UAM and OECD/NEA MHTGR-350) and refinement of a few-group Pebble Bed Reactor (PBR) cross section (XS) generation methodology. Funding will be requested in FY21 to produce the final reports for the two benchmarks and continue the development of the PBR XS generation methodology. Additional (non-ART) HTGR-related support work at INL NEAMS: HTR-Application work package at INL Create a benchmark for the pebble shuffling and depletion algorithms being developed for NEAMS Griffin code. iFOA award with X-Energy: Develop independent Monte Carlo model of Xe-100 design. Independent design confirmatory analysis of Xe-100 design using NEAMS tools Griffin and Pronghorn. Support X-Energy design team to use their own legacy design tools (VSOP99 and MGT). Support NEAMS Griffin and Pronghorn development team for the iFOA needs (received $50K additional funding for required development).
This report presents the results from code-to-code comparisons for a prismatic modular high-temperature gas-cooled reactor 350-MW design for steady-state neutron transport calculations. Integral parameters as well as power and flux distributions are provided. Differences between solutions from diffusion and transport operators are analysed. Effects of control rod homogenization between full block and one sixth block are discussed.
The objective of this study is to develop a 3D/NK model to study the load following operation of a Modular High-Temperature Gas-Cooled Reactor (MHTGR). The selected design is the 350 MW prismatic, graphite moderated, helium cooled thermal reactor based on the MHTGR-350 transient benchmark led by the High-Temperature Gas-Cooled Reactor (HTGR) Methods Core Simulation Group at Idaho National Laboratory (INL) in the framework of the Organization for Economic Cooperation and Development Nuclear Energy Agency (OECD/NEA). This kind of reactor usually reacts very slowly to the perturbation of the core parameters due to the large amount of graphite in the core. This kind of behavior promotes the reactor stability but on the other hand limits the reactor load-following operability. Recently advances in gas reactor designs have made load-following in gas reactors a feasible and achievable goal. Modern nuclear reactors (such as the MHTGR-350) are designed to withstand the structural stresses associated with load-following. Operating the reactor in load-following mode will inevitably reduce the load factor. Although a higher load factor means more revenue and the best usage of the fuel, following the variable energy demand will increase the maximum achievable fraction of generated nuclear power, being no more limited to the base load power generation. In general, if low impact on material aging and the safe operability are demonstrated the plant economics will be minimally affected. In order to ensure that the system can be safely operated in a load-following mode an extensively study has been carried out. Some tests with linear coolant mass flow rate change demonstrated that the reactor behavior is suitable for operation in load following mode. This assumption has been confirmed by a 4 days load following transient test in which the reactor supplied the requested power with a negligible error.
Not Available
This report details the Parallel and Highly Innovative Simulation for INL Code System (PHISICS)/Reactor Excursions and Leak Analysis Program (RELAP5)-3D results obtained for the neutronics stand-alone core exercises defined for Phase II of the International Atomic Energy Agency (IAEA) Coordinated Research Project (CRP) on high-temperature gas cooled reactor (HTGR) uncertainty analysis in modeling (UAM). The Phase II models and results are linked to the earlier Standardized Computer Analyses for Licensing Evaluation (SCALE)/Sampler/New ESC-based Weighting Transport (NEWT) data generated for the lattice physics (lattice) stage Phase I of the CRP. The focus of this report is the propagation of cross-section uncertainties from the lattice to the core calculation (core) phase of the prismatic 350 megawatt (MW) General Atomics (GA) Modular HTGR (MHTGR). The Phase II neutronics exercises consist of two sub-cases (II-2a and II-2b) specified for the fresh and mixed core loading of the MHTGR-350 prismatic high-temperature reactor design. Exercises II-2a and II-2b are performed without temperature feedback using isothermal temperature profiles. For the nominal lattice physics (i.e., best-estimate) model, a series of fresh and depleted single block and super cell SCALE/KENO and SCALE/NEWT models were developed at Idaho National Laboratory (INL) to assess the impact of spectral effects on the few-group cross sections. A combination of these lattice cells were used in a super cell calculation to construct 8-group cross-section libraries for use in the INL-developed PHISICS/RELAP5-3D code suite. The block-level homogenized libraries were assigned to the 220 fuel zones utilized in the MHTGR-350 PHISICS core model, according to the fresh and mixed fresh/depleted core loading pattern. In order to evaluate the effect of uncertainty propagation, several sets consisting of 1,000 perturbed NEWT lattice and PHISICS/RELAP5-3D core calculations were performed using the SCALE 6.2 ENDF/B-VII.1 cross-section co-variance data and the stochastic sampling module Sampler in SCALE 6.2.0. The Figures of Merit (FOM) investigated include the mean and standard deviation uncertainty values obtained for the eigenvalues, control rod worth values, block-averaged power profiles, power axial offsets, and isothermal temperature feedback coefficients. A sensitivity study on the main nuclide reaction contributors to the FOM uncertainties has not yet been performed since the SCALE/PHISICS/RAVEN coupling with ENDF/B-VII co-variance data is still being developed. It was found that uncertainties in the cross sections lead to uncertainties in the local power values of up to 1.5%. The variances between the fresh and mixed/depleted core models are not as large as the axial variations between the top and bottom within each core model. The core eigenvalue uncertainty is approximately 0.5%, which is significant in comparison to typical eigenvalue difference targets (less than ~0.1% for LWRs). The power peaking and axial offset uncertainties are smaller (0.10% – 0.15%) and probably below the level of significance in typical core design metrics. The use of an 8-group energy structure slightly under-estimates some of the uncertainties, but in absolute terms, the uncertainty results are reasonably close to the 26-group results. The 26- and 8-group mean and nominal results differ by a larger degree, and if it can be afforded in terms of calculation resources, the 26-group structure should be used for HTGR calculations. The 8-group structure can, however, still be useful for reasonably accurate uncertainty assessments of transient cases where computational time is important. It was furthermore found that the use of a super cell during the cross-section generation process for better representation of the spectral environment at the core periphery did not lead to significant changes in the core eigenvalues, axial offset, and power peaking uncertainties. The impact of the super cell cross sections on the nominal and mean eigenvalues is, however, important enough (0.6% – 1.1% lower) to justify the use of these super cells for HTGR core simulation to represent the softer spectral environment in the core peripheral regions for nominal best-estimate calculations. The use of super cells for HTGR uncertainty studies is, therefore, not strictly necessary, but the improvements in nominal results could justify their use.
The poster presents the results of the current research activities I am carrying on for the verification and validation of the MOOSE based code Pronghorn.
We conducted reactor performance calculations to assess the potential design basis accident performance of HTGR fuel designs. Three Fully Ceramic Microencapsulated (FCM) fueled HTGR designs were developed in a previous work (Lu et al., 2018). The maximum fuel temperature in the cores fueled by these three FCM fuels was predicted to be higher than that in the reference 350-MWt mHTGR core in both normal operating conditions and during representative design basis accidents (Lu and Brown, 2019). To better understand the potential safety margins in mHTGR design basis accidents, we performed thermal-hydraulics sensitivity studies to investigate how maximum fuel temperature varies considering various parameters, e.g. thermal properties, within the ranges corresponding to the differences between the FCM-fueled prismatic mHTGR cores and the reference core with conventional fuel compacts. We found that the difference in the steady-state axial power distribution contributed the most to the difference in the maximum fuel temperature, in both normal operation and design basis accidents.Experimental data suggested that the annealing process of irradiation defects in SiC would be rapid at mHTGR relevant fuel temperatures. The bounding potential impact of the SiC annealing on the maximum fuel temperature was analyzed considering both the thermal conductivity recovery and the Wigner energy release due to the annealing of SiC. We found that the defect annealing process in SiC would at most increase the peak maximum fuel temperature of an FCM-fueled core by 40 K in loss of forced cooling accidents and by 10 K in a control rod withdrawal accident. Finally, additional experiments on the SiC defect annealing kinetics and Wigner energy release in more relevant conditions are needed.
The IAEA Coordinated Research Project (CRP) on High Temperature Gas Cooled Reactor (HTGR) Uncertainties in Modeling (UAM) has been actively supported by the HTGR Methods group at Idaho National Laboratory since 2013. The INL team is responsible for the development of the prismatic reactor design exercises, based on the 350 MW General Atomics Modular HTGR (MHTGR). The focus of this paper is the reporting of the INL results obtained for the propagation of the lattice cross section uncertainties to the stand-alone neutronics simulation of the full MHTGR-350 core. For the nominal (i.e. best-estimate) model, a series of fresh and depleted single block and super cell SCALE/KENO and SCALE/NEWT models were developed at INL to assess spectral effects in the MHTGR-350, and a combination of these lattice cells were used to construct 8-group cross section libraries for use in the INL-developed PHISICS/RELAP5-3D code suite. The block-level homogenized libraries were assigned to the 220 fuel zones utilized in the MHTGR-350 PHISICS core model, according to the fresh and mixed fresh/depleted core loading pattern. A set of 1,000 perturbed NEWT lattice and PHISICS/RELAP5-3D core calculations were performed using the stochastic sampling module SAMPLER in SCALE 6.2. The paper discusses the mean and standard deviation values obtained for the eigenvalue, power offset and peak axial power density uncertainty results for this sequence of 1,000 lattice-to-core MHTGR-350 simulations.
presentation on Decay Heat Surrogate modeling for High Temperature Reactors
The accuracy of the safety analysis of Nuclear Power Plants, in general, and the High Temperature Reactors, in particular, is driven by several factors, among which the accuracy of decay heat curves or calculation. This paper is aimed to present a methodology based on the usage of the RAVEN code for the construction of a multi-dimensional decay heat curve for High Temperature Reactors, via calculations performed by ORIGEN. The main goal of this activity has been the identification of a model able to surrogate the phenomenology of the decay heat after shutdown, satisfying the following requirements: 1) Reasonable prediction accuracy till 1 month after the shutdown, 2) Ability to capture the main deviation effects determined by field conditions (e.g. burn-up, fuel temperature, fissile enrichment, etc.), 3) As easy as possible formalism in order to possibly allow the implementation of the curve into system codes (e.g. RELAP5-3D) inputs exploiting, for example, control variable capabilities. Three surrogate models (also known as decay heat curves in the safety analysis nomenclature) have been identified: 1) Spline Exponential surrogate model, 2) A Support Vector Regression model and, 3) A Dynamic Mode Decomposition model. The aim of this paper is to present the mathematical background of the identified surrogate models and their performance in the prediction of decay heat evolution for High Temperature Reactors. A preliminary comparison of the surrogate model performances is finally reported.
In February 2009, the Technical Working Group on Gas Cooled Reactors of the International Atomic Energy Agency (IAEA) recommended that the proposed Coordinated Research Project (CRP) on the High-Temperature Gas Cooled Reactor (HTGR) Uncertainty Analysis in Modeling (UAM) be implemented. This CRP is a continuation of the previous IAEA and Organisation for Economic Cooperation and Development (OECD)/Nuclear Energy Agency (NEA) international activities on verification and validation of available analytical capabilities for HTGR simulation for design and safety evaluations. Within the framework of these activities different numerical and experimental benchmark problems were performed, and insight was gained about specific physics phenomena and the adequacy of analysis methods. Because the prismatic design specification included in this report is based directly on the OECD/NEA Modular HTGR (MHTGR) 350 MW benchmark, participants in both activities can leverage their core models developed for the OECD/NEA benchmark for this CRP benchmark with only minor changes. The CRP on the HTGR UAM Phase II specifications is also directly linked to the Phase I specification document, since the core models required for Phase II exercises are constructed using the lattice models and cross-section libraries developed for Phase 1. It was decided at the Third Research Coordination Meeting (RCM) in May 2017 that the initial scope of CRP activities will be reduced to match the formally approved remaining contract period (June 2019), as well as limited funding and resource availability. A summary of the revised Phases I–IV exercise definitions is provided here.
An assessment of advanced reactor technology options was conducted to provide a sound comparative technical context for future decisions by the U.S. Department of Energy (DOE) concerning these technologies. Strategic objectives were established that span a wide variety of important missions, and advanced reactor technology needs were identified based on recent DOE and international studies. A broad team of stakeholders from industry, academia, and government was assembled to develop a comprehensive set of goals, criteria, and metrics to evaluate advanced irradiation test and demonstration reactor concepts. Point designs of a select number of concepts were commissioned to provide a deeper technical basis for evaluation. The technology options were compared on the bases of technical readiness and the ability to meet the different strategic objectives. Using the study's evaluation criteria and metrics, an independent group of experts from industry, universities, and national laboratories scored each of the point designs. Pathways to deployment for concepts of varying technical maturities were estimated for the different demonstration systems with regard to cost, schedule, and possible licensing approaches. This study also presents the trade-offs that exist among the different irradiation test reactor options in terms of the ability to conduct irradiations in support of advanced reactor research and development and to serve potential secondary missions. The main findings of the study indicate the following: (1) for industrial process heat supply, a high-temperature gas-cooled reactor is the best choice because of the high outlet temperature of the reactor and its strong passive and inherent safety characteristics; (2) for resource utilization and waste management, a sodium-cooled fast reactor (SFR) is best because of the use of a fast flux to destroy actinides; (3) to realize the advantages of a promising but less-mature technology, a fluoride salt-cooled high-temperature reactor and a lead-cooled fast reactor fare about the same; (4) for fulfilling the needs of a materials test reactor, a SFR is considered best because of its ability to produce high fast flux, incorporate test loops, and provide additional large volumes for testing.
An assessment of advanced reactor technology options was conducted to provide a sound comparative technical context for future decisions by the Department of Energy (DOE) concerning these technologies. Strategic objectives were established that span a wide variety of important missions and advanced reactor technology needs were identified based on recent Department of Energy and international studies. A broad team of stakeholders from industry, academia and government was assembled to develop a comprehensive set of goals, criteria and metrics to evaluate advanced irradiation test and demonstration reactor concepts. Point designs of a select number of concepts were commissioned to provide a deeper technical basis for evaluation. The technology options were compared on the bases of technical readiness and the ability to meet the different strategic objectives. Using the study’s evaluation criteria and metrics, an independent group of exerts from industry, universities and national labs scored each of the point designs. Pathways to deployment for concepts of varying technical maturity were estimated for the different demonstration systems with regard to cost, schedule and possible licensing approaches. Furthermore, this study also presents the tradeoffs that exist among the different irradiation test reactor options in terms of the ability to conduct irradiations in support of advanced reactor research and development (R&D) and to serve potential secondary missions.
The Very High Temperature Critical Assembly (VHTRC) experiment represents one of the few data sets available for the validation of HTGR lattice physics. Within the framework of the IAEA Coordinated Research Project on HTGR Uncertainty Analysis in Modeling, uncertainty and sensitivity analyses of this graphite-moderated facility are performed as the validation reference to the prismatic MHTGR-350 fuel block calculations. Nominal multi-group and continuous-energy criticality calculations with the KENO-VI Monte Carlo code of the SCALE code package are compared with the continuous-energy Monte Carlo Code Serpent. Good agreement with a maximum difference of 250 pcm is obtained. The experimental data set, however, differs by several hundred pcm with the results of both codes when using the ENDF-VII.0 library. When using ENDF/B-VII.1 data, this difference is reduced to a few hundred pcm and the calculations lie within the experimental error bars. Uncertainties of the VHTRC multiplication factors due to uncertainties in nuclear data are determined with SAMPLER/KENO-VI of SCALE 6.2 and with continuous-energy TSUNAMI of SCALE 6.2. For all experimental configurations, the obtained uncertainty is found to be 0.58% when using ENDF/B-VII.0 data. The top contributor to this uncertainty is the average number of neutrons per fission event of U-235. With ENDF/B-VII.1 data, uncertainties of about 0.66% are obtained in particular due to an increased uncertainty of U-235 nu-bar in the latest ENDF release. In conclusion, when considering these nuclear data uncertainties, the obtained 1s uncertainty intervals are overlapping with the experimental error bars.
Accurate, high-resolution full core simulations of prismatic high temperature reactors for burnup and transient analysis remain a challenge. The cores are geometrically large, but some features are quite small (tri-structural isotropic (TRISO) particles, burnable poison pellets). The treatment of both neutron scattering in graphite and resonance capture are complex and not adequately captured using the methods traditionally used in High Temperature Gas-cooled Reactors (HTGR) and commonly used in Light Water Reactors (LWR). For transient analysis, temperature feedback is a function of the TRISO fuel form, but full core models cannot resolve phenomena at this scale without averaging over space and energy. For burnup calculations, a second level of heterogeneity must be resolved to capture the local effects of fuel and burnable poisons, while accurately propagating their effects through and between blocks. The HTGR Methods and Simulation group has been utilizing the INL-developed PHISICS/RELAP5-3D{sup C} (P/R), code suite for participation in the Organization for Economic Cooperation and Development (OECD) Modular High Temperature Gas Cooled Reactor (MHTGR) Benchmark, funded by the US Department of Energy (DOE) under the Advanced Reactor Technologies (ART) program. The MHTGR-350 benchmark consists of several lattice, steady-state and transient exercises, and the P/R code has been successfully applied to most of the cases defined. In addition to this code-to-code verification activity, it is planned that P/R will be validated using data from several Loss of Forced Cooling (LOFC) tests performed at the High Temperature Test Reactor (HTTR) in a joint effort with Japan Atomic Energy Agency (JAEA) under the Civil Nuclear Energy Working Group (CNWG) project. These verification and validation simulations will identify code and model discrepancies, sensitivities, and establish the current state-of-the-art in HTGR simulation. The Department of Astronautical, Electrical and Energy Engineering (DIAEE), 'Sapienza' University has been involved in the development of P/R since 2014 through various graduate and PhD student projects. In the framework of this collaboration the P/R optimization for application on the OECD MHTGR-350 and HTTR models will be carried out.
A thorough understanding of oxidation is important when considering the health and integrity of graphite components in graphite reactors. For the next generation of graphite reactors, HTGRs specifically, an unlikely air ingress has been deemed significant enough to have made its way into the licensing applications of many international licensing bodies. While a substantial body of literature exists on nuclear graphite oxidation in the presence of molecular oxygen and significant efforts have been made to characterize oxidation kinetics of various grades, the value of existing information is somewhat limited. Often, multiple competing processes, including reaction kinetics, mass transfer, and microstructural evolution, are lumped together into a single rate expression that limits the ability to translate this information to different conditions. This article reviews the reaction of graphite with molecular oxygen in terms of the reaction kinetics, gas transport, and microstructural evolution of graphite. It also presents the foundations of a model for the graphite-molecular oxygen reaction system that is kinetically independent of graphite grade, and is capable of describing both the bulk and local oxidation rates under a wide range of conditions applicable to air-ingress.
A collaborative effort between Japan Atomic Energy Agency (JAEA) and Idaho National Laboratory (INL) as part of the Civil Nuclear Energy Working Group is underway to model the high temperature engineering test reactor (HTTR) loss of forced cooling (LOFC) transient that was performed in December 2010. The coupled version of RELAP5-3D, a thermal fluids code, and PHISICS, a neutronics code, were used to model the transient. The focus of this report is to summarize the changes made to the PHISICS-RELAP5-3D code for implementing an adaptive time step methodology into the code for the first time, and to test it using the full HTTR PHISICS/RELAP5-3D model developed by JAEA and INL and the LOFC simulation. Various adaptive schemes are available based on flux or power convergence criteria that allow significantly larger time steps to be taken by the neutronics module. The report includes a description of the HTTR and the associated PHISICS/RELAP5-3D model test results as well as the University of Rome sub-contractor report documenting the adaptive time step theory and methodology implemented in PHISICS/RELAP5-3D. Two versions of the HTTR model were tested using 8 and 26 energy groups. It was found that most of the new adaptive methods lead to significant improvements in the LOFC simulation time required without significant accuracy penalties in the prediction of the fission power and the fuel temperature. In the best performing 8 group model scenarios, a LOFC simulation of 20 hours could be completed in real-time, or even less than real-time, compared with the previous version of the code that completed the same transient 3-8 times slower than real-time. A few of the user choice combinations between the methodologies available and the tolerance settings did however result in unacceptably high errors or insignificant gains in simulation time. The study is concluded with recommendations on which methods to use for this HTTR model. An important caveat is that these findings are very model-specific and cannot be generalized to other PHISICS/RELAP5-3D models.