Search NASASearch

Engineering topics

Stubbs, Timothy J.

Publications and source records attributed to Stubbs, Timothy J..

Elliptical ejecta of asteroid Dimorphos is due to its surface curvature

Kinetic deflection is a planetary defense technique delivering spacecraft momentum to a small body to deviate its course from Earth. The deflection efficiency depends on the impactor and target. Among them, the contribution of global curvature was poorly understood. The ejecta plume created by NASA’s Double Asteroid Redirection Test impact on its target asteroid, Dimorphos, exhibited an elliptical shape almost aligned along its north-south direction. Here, we identify that this elliptical ejecta plume resulted from the target’s curvature, reducing the momentum transfer to 44 ± 10% along the orbit track compared to an equivalent impact on a flat target. We also find lower kinetic deflection of impacts on smaller near-Earth objects due to higher curvature. A solution to mitigate low deflection efficiency is to apply multiple low-energy impactors rather than a single high-energy impactor. Rapid reconnaissance to acquire a target’s properties before deflection enables determining the proper locations and timing of impacts.

79 ASTRONOMY AND ASTROPHYSICS

Earthshine as an Illumination Source at the Moon

Earthshine is the dominant source of natural illumination on the surface of the Moon during lunar night, and at some locations within permanently shadowed regions (PSRs) near the poles that never receive direct sunlight. As such, earthshine has the potential to enable the scientific investigation and exploration of conditions in areas of the Moon that are either temporarily or permanently hidden from the Sun. Earthshine has also been used to refer to Earthlight reflected from the lunar surface, but in this study we use it to refer specifically to Earthlight incident at the Moon. Under certain circumstances, the heat flux from earthshine could also influence the transport and cold-trapping of volatiles present in the very coldest areas within PSRs. In this study, Earth's spectral irradiance, as it would appear at the Moon in the solar reflectance band (0.3–3.0 µm) and at thermal emission wavelengths (3–50 µm), is examined with a suite of model image cubes and whole-disk spectra created using the Virtual Planetary Laboratory (VPL) three-dimensional (latitude, longitude and altitude) modeling capability. At the Moon, the broadband, hemispherical irradiance from Earth at full-phase is approximately 0.15 W m−2 with comparable contributions from solar reflectance and thermal emission; for context, this about 0.01% that of solar irradiance and has an equivalent temperature of around 40 K. Over the simulated timeframe, spanning two lunations, Earth's thermal irradiance shows very little net change (less than a few mW m−2 resulting from cloud variability and the south-to-north motion of the sub-observer latitude on Earth). In the solar band, Earth's diurnally averaged light curve at phase angles g ≤ 60° is well-fit using a Henyey–Greenstein integral phase function. At wavelengths longward of about 0.7 µm, near the well-known vegetation “red edge”, Earth's reflected solar radiance shows significant diurnal modulation as a result of the broad maximum in projected landmass at terrestrial longitudes between 60°W and 0°, as well as from the distribution of clouds. A simple formulation with adjustable coefficients is presented, condensed from the VPL model grid, for estimating Earth's hemispherical irradiance at the Moon as a function of wavelength, phase angle and sub-observer coordinates (terrestrial latitude and longitude). Uncertainties in any one prediction are estimated to be 10–12% at 0.3 µm, rising to >25% near 2.5 µm as a result of the increasing relative brightness and unpredictable influence of clouds. Although coefficient values are derived from a suite of spring equinox models, the approximation appears to be valid for all seasons, to within the stated uncertainties. It is demonstrated that earthshine is sufficiently bright to serve as a natural illumination source for optical measurements on a robotic lander/rover, allowing the identification of water ice mixed with regolith at the percent-level of fractional area.

Surface

LADEE UVS Observations of Atoms and Dust in the Lunar Tail

The Lunar Atmosphere and Dust Environment Explorer (LADEE) was a lunar orbiter launched in September 2013 that investigated the composition and temporal variation of the tenuous lunar exosphere and dust environment. A major goal of the mission was to characterize the dust exosphere prior to future lunar exploration activities, which may alter the lunar environment. The Ultraviolet/Visible Spectrometer (UVS) onboard LADEE addresses this goal, utilizing two sets of optics: a limbviewing telescope, and a solar-viewing telescope. We report on spectroscopic (approximately 280 - 820 nm) observations viewing down the lunar wake or along the 'lunar tail' from lunar orbit. Prior groundbased studies have observed the emission from neutral sodium atoms extended along the lunar tail, so often this region is referred to as the lunar sodium tail. UVS measurements were made on the dark side of the moon, with the UVS limb-viewing telescope pointed outward in the direction of the Moon's wake (almost anti-sun), during different lunar phases. These UVS observation activities sample a long column and allow the characterization of scattered light from dust and emission lines from atoms in the lunar tail. Observations in this UVS configuration show the largest excess of scattered blue light in our data set, indicative of the presence of small dust grains in the tail. Once lofted, nanoparticles may become charged and picked up by the solar wind, similar to the phenomena witnessed above Enceladus's northern hemisphere or by the STEREO/WAVES instrument while close to Earth's orbit. The UVS data show that small dust grains as well as atoms become entrained in the lunar tail.

Dust and Solar Wind

ROSAT Observations of Solar Wind Charge Exchange with the Lunar Exosphere

We analyze the ROSAT PSPC soft X-ray image of the Moon taken on 29 June 1990 by examining the radial profile of the count rate in three wedges, two wedges (one north and one south) 13-32 degrees off (19 degrees wide) the terminator towards the dark side and one wedge 38 degrees wide centered on the anti-solar direction. The radial profiles of both the north and the south wedges show substantial limb brightening that is absent in the 38 degree wide antisolar wedge. An analysis of the count rate increase associated with the limb brightening shows that its magnitude is consistent with that expected due to solar wind charge exchange (SWCX) with the tenuous lunar atmosphere. Along with Mars, Venus, and Earth, the Moon represents another solar system body at which solar wind charge exchange has been observed. This technique can be used to explore the solar wind-lunar interaction.

Collier, Michael R.

Doubly-Shadowed Regions in Lunar Polar Craters: Hydrogen Accumulation in the Presence of Recursive Plasma Wakes

Permanently shadowed regions (PSRs) of the Moon have been identified as unique environments of extreme cold and comprise a natural cold trap for sequestering volatiles [Paige et al. 2010]. The diverse chemical composition of the LCROSS impact plume provided evidence for a volatile-rich and chemically-complex PSR environment [Cola prete et al. 2010, Schultz et al. 2010]. Additionally, the polar electrostatic environment is highly complex, with the possibility of strong, localized electric fields that divert solar wind ions directly into polar cold traps [Farrell et al. 2010, Zimmerman et al. 2011]. Thus, regional plasma physics processes couple directly with volatile sequestration. In the present work, kinetic simulations show that recursive plasma wake structure arises in the presence of step-like topographic features (Le. doubly-shadowed craters). Combining the plasma code with a numerical sputtering model demonstrates that solar wind protons can be either a hydrogen source via implantation or a volatile loss mechanism via sputtering, depending on properties of the regolith and solar wind. The present model provides a novel theoretical pathway toward understanding the lunar surface/solar wind physical and chemical interactions for complex topography near the poles.

Zimmerman, Michael I.

Metallic Species, Oxygen and Silicon in the Lunar Exosphere: Upper Limits and Prospects for LADEE Measurements

The only species that have been so far detected in the lunar exosphere are Na, K, Ar,and He. However, models for the production and loss of species derived from the lunarregolith through micrometeoroid impact vaporization, sputtering, and photon-stimulateddesorption, predict that a host of other species should exist in the lunar exosphere.Assuming that loss processes are limited to ballistic escape, photoionization, and recyclingto the surface, we have computed column abundances and compared them to publishedupper limits for the Moon. Only for Ca do modeled abundances clearly exceed theavailable measurements. This result suggests the relevance of some loss processes thatwere not included in the model, such as the possibility of gas-to-solid phasecondensation during micrometeoroid impacts or the formation of stable metallic oxides.Our simulations and the recalculation of efficiencies for resonant light scattering showthat models for other species studied are not well constrained by existingmeasurements. This fact underlines the need for improved remote and in situmeasurements of the lunar exosphere such as those planned by the Lunar Atmosphereand Dust Environment Explorer (LADEE) spacecraft. Our simulations of the LADEEneutral mass spectrometer and visibleultraviolet spectrometer indicate that LADEE measurements promise to provide definitive observations or set stringent upper limitsfor all regolith-driven exospheric species. We predict that observations by LADEE willconstrain assumed model parameters for the exosphere of the Moon.

lunar exosphere

Illumination Conditions at the Asteroid 4 Vesta: Implications for the Presence of Water Ice

The mean illumination conditions and surface temperatures over one orbital period are calculated for the Asteroid 4 Vesta using a coarse digital elevation model produced from Hubble Space Telescope images. Even with the anticipated effects of finer-scale topography taken into account, it is unlikely that any significant permanently shadowed regions currently exist on Vesta due to its large axial tilt (approx. = 27deg). However, under present day conditions, it is predicted that about half of Vesta's surface has an average temperature of less than 145 K, which, based on previous thermal modeling of main belt asteroids, suggests that water ice could survive in the top few meters of the vestal regolith on billion-year timescales.

Stubbs, Timothy J.

The Lunar Dust Pendulum

Shadowed regions on the lunar surface acquire a negative potential. In particular, shadowed craters can have a negative potential with respect to the surrounding lunar regolith in sunlight, especially near the terminator regions. Here we analyze the motion of a positively charged lnnar dust grain in the presence of a shadowed crater at a negative potential in vacuum. Previous models describing the transport of charged lunar dust close to the surface have typically been limited to one-dimensional motion in the vertical direction, e.g. electrostatic levitation; however. the electric fields in the vicinity of shadowed craters will also have significant components in the horizontal directions. We propose a model that includes both the horizontal and vertical motion of charged dust grains near shadowed craters. We show that the dust grains execute oscillatory trajectories and present an expression for the period of oscillation drawing an analogy to the motion of a pendulum.

Kuntz, Kip

A Fractal Model for the Capacitance of Lunar Dust and Lunar Dust Aggregates

Lunar dust grains and dust aggregates exhibit clumping, with an uneven mass distribution, as well as features that span many spatial scales. It has been observed that these aggregates display an almost fractal repetition of geometry with scale. Furthermore, lunar dust grains typically have sharp protrusions and jagged features that result from the lack of aeolian weathering (as opposed to space weathering) on the Moon. A perfectly spherical geometry, frequently used as a model for lunar dust grains, has none of these characteristics (although a sphere may be a reasonable proxy for the very smallest grains and some glasses). We present a fractal model for a lunar dust grain or aggregate of grains that reproduces (1) the irregular clumpy nature of lunar dust, (2) the presence of sharp points, and (3) dust features that span multiple scale lengths. We calculate the capacitance of the fractal lunar dust analytically assuming fixed dust mass (i.e. volume) for an arbitrary number of fractal levels and compare the capacitance to that of a non-fractal object with the same volume, surface area, and characteristic width. The fractal capacitance is larger than that of the equivalent non-fractal object suggesting that for a given potential, electrostatic forces on lunar dust grains and aggregates are greater than one might infer from assuming dust grains are sphericaL Consequently, electrostatic transport of lunar dust grains, for example lofting, appears more plausible than might be inferred by calculations based on less realistic assumptions about dust shape and associated capacitance.

Collier, Michael R.

The Lunar Dust Pendulum

Shadowed regions on the lunar surface acquire a negative potential. In particular, shadowed craters can have a negative potential with respect to the surrounding lunar regolith in sunlight, especially near the terminator regions. Here we analyze the motion of a positively charged lunar dust grain in the presence of a shadowed crater at a negative potential in vacuum. Previous models describing the transport of charged lunar dust close to the surface have typically been limited to one-dimensional motion in the vertical direction, e.g. electrostatic levitation; however, the electric fields in the vicinity of shadowed craters will also have significant components in the horizontal directions. We propose a model that includes both the horizontal and vertical motion of charged dust grains near shadowed craters. We show that the dust grains execute oscillatory trajectories and present an expression for the period of oscillation drawing an analogy to the motion of a pendulum.

Collier, Michael R.

On the Role of Dust in the Lunar Ionosphere

Evidence suggests that electron concentrations above the dayside lunar surface can be significantly higher than expected from either the photo-ionization of exospheric neutrals or any other well-known process. The Luna 19 mission performed dual-frequency radio occultation experiments in order to determine electron column concentrations above the lunar limb as a function of tangent height (shown in the figure below), The resulting electron concentration profiles surprisingly indicated a peak of approx.500-1000/cu cm and scale heights of approx. 10-30 km. It has been suggested that electrically charged exospheric dust could contribute to these electron cnhancemcnts2 , Here we describe how to estimate the electrons produced by photo-charged dust, which is then used to predict electron concentrations from exospheric dust distribution models that are based on the "excess brightness" observed in Apollo 15 coronal photographs. The results indicate that radio occultation measurements likely provide a valuable perspective on the role of dust in the lunar environment.

Stubbs, Timothy J.

Metallic Species, Oxygen and Silicon in the Lunar Exosphere: Upper Limits and Prospects for LADEE Measurements

The only species that have been continued in the lunar exosphere are Na, K, Ar, and He. Models for the production and loss of lunar regolith-derived exospheric species from source processes including micrometeoroid impact vaporization, sputtering. and, for Na and K, photon-stimulated desorption, predict a host of other species should exist in the lunar exosphere. Assuming that loss processes are limited to ballistic escape and recycling to the surface, we have computed column abundances and compared them to published upper limits from the Moon and to detected abundances from Mercury. Only for Ca do the available measurements show a clear deficiency compared to the model estimates. This result suggests the importance of loss processes not included in the model, such as the possibility of gas-to-solid phase condensation during micrometeoroid impacts or the formation of stable metallic oxides, and underlines the need for improved spectroscopic measurements of the lunar exosphere. Simulations of the neutral mass (NMS) and visible/ultraviolet spectrometry (UVS) investigations planned by the Lunar Atmosphere and Dust Environment Explorer (LADEE) spacecraft are presented. Our calculations indicate that LADEE measurements promise to make definitive observations or set stringent upper limits for all regolith-driven exospheric species. Our models, along with LADEE observations, will constrain assumed model parameters for the Moon, such as sticking coefficients, source processes. and velocity distributions.

Sarantos, Menelaos

Lunar Surface Electric Potential Changes Associated with Traversals through the Earth's Foreshock

We report an analysis of one year of Suprathermal Ion Detector Experiment (SIDE) Total Ion Detector (TID) resonance events observed between January 1972 and January 1973. The study includes only those events during which upstream solar wind conditions were readily available. The analysis shows that these events are associated with lunar traversals through the dawn flank of the terrestrial magnetospheric bow shock. We propose that the events result from an increase in lunar surface electric potential effected by secondary electron emission due to primary electrons in the Earth's foreshock region (although primary ions may play a role as well). This work establishes (1) the lunar surface potential changes as the Moon moves through the terrestrial bow shock, (2) the lunar surface achieves potentials in the upstream foreshock region that differ from those in the downstream magnetosheath region, (3) these differences can be explained by the presence of energetic electron beams in the upstream foreshock region and (4) if this explanation is correct, the location of the Moon with respect to the terrestrial bow shock influences lunar surface potential.

Collier, Michael R.

Lunar Surface Potential Increases during Terrestrial Bow Shock Traversals

Since the Apollo era the electric potential of the Moon has been a subject of interest and debate. Deployed by three Apollo missions, Apollo 12, Apollo 14 and Apollo 15, the Suprathermal Ion Detector Experiment (SIDE) determined the sunlit lunar surface potential to be about +10 Volts using the energy spectra of lunar ionospheric thermal ions accelerated toward the Moon. We present an analysis of Apollo 14 SIDE "resonance" events that indicate the lunar surface potential increases when the Moon traverses the dawn bow shock. By analyzing Wind spacecraft crossings of the terrestrial bow shock at approximately this location and employing current balancing models of the lunar surface, we suggest causes for the increasing potential. Determining the origin of this phenomenon will improve our ability to predict the lunar surface potential in support of human exploration as well as provide models for the behavior of other airless bodies when they traverse similar features such as interplanetary shocks, both of which are goals of the NASA Lunar Science Institute's Dynamic Response of the Environment At the Moon (DREAM) team.

Collier, Michael R.

The Lunar Potential Determination Using Apollo-Era Data and Modern Measurements and Models

Since the Apollo era the electric potential of the Moon has been a subject of interest and debate. Deployed by three Apollo missions, Apollo 12, Apollo 14 and Apollo 15, the Suprathermal Ion Detector Experiment (SIDE) determined the sunlit lunar surface potential to be about +10 Volts using the energy spectra of lunar ionospheric thermal ions accelerated toward the Moon. More recently, the Lunar Prospector (LP) Electron Reflectometer used electron distributions to infer negative lunar surface potentials, primarily in shadow. We will present initial results from a study to combine lunar surface potential measurements from both SIDE and the LP/Electron Reflectometer to calibrate an advanced model of lunar surface charging which includes effects from the plasma environment, photoemission, secondaries ejected by ion impact onto the lunar surface, and the lunar wake created downstream by the solar wind-lunar interaction.

Collier, Michael R.

Neutral Solar Wind Generated by Lunar Exospheric Dust at the Terminator

We calculate the flux of neutral solar wind observed on the lunar surface at the terminator due to solar wind protons penetrating exospheric dust with: (1) grains larger that 0.1 microns and (2) grains larger than 0.01 microns. For grains larger than 0.1 microns, the ratio of the neutral solar wind to solar wind flux is estimated to be approx.10(exp -4)-10(exp -3) at solar wind speeds in excess of 800 km/s, but much lower (less than 10(exp -5) at average to low solar wind speeds. However, when the smaller grain sizes are considered, the ratio of the neutral solar wind flux to solar wind flux is estimated to be greater than or equal to 10(exp -5) at all speeds and at speeds in excess of 700 km/s reaches 10(exp -3)-10(exp -2). These neutral solar wind fluxes are easily measurable with current low energy neutral atom instrumentation. Observations of neutral solar wind from the surface of the Moon could provide a very sensitive determination of the distribution of very small dust grains in the lunar exosphere and would provide data complementary to optical measurements at ultraviolet and visible wavelengths. Furthermore, neutral solar wind, unlike its ionized counterpart, is .not held-off by magnetic anomalies, and may contribute to greater space weathering than expected in certain lunar locations.

Collier, Michael R.