Engineering topics

Su, C. H.

Publications and source records attributed to Su, C. H..

7 records

NASA NTRS2002

Technique for Determining the Viscosity and Electrical Conductivity of Semiconducting Liquids

A novel apparatus for determining the viscosity and electrical conductivity of semiconducting liquids has been developed at NASA/MSFC. The apparatus is based on the transient torque technique and utilizes a 125 micrometer diameter quartz fiber as a torsion wire and a sensitive angular detector to measure the deflection angle of the crucible containing the liquid. A rotating flow is induced in the semiconducting melt by the application of a rotating magnetic field and measurement of the magnitude and transient behavior of the induced deflection angle allows the simultaneous determination of the viscosity and electrical conductivity of the melt. Measurements at room temperature and up to 900 C were made on high purity melts.

Li, C.↗

NASA NTRS2001

Transport Phenomena of Off-Axis Sputtering Deposition

Various high quality epitaxial films, especially oxides, have been synthesized using off-axis sputtering deposition. In this presentation, we report the experiment results of ZnO films grown by the off-axis sputtering deposition. Films were synthesized in temperatures ranged from room temperature to 600 C, and pressures from 5 mTorr to 150 mTorr. Film growth rate was measured by surface profilometer, ellipsometer, and wavelength dispersive spectrometry. Due to the collisions between the sputtered species and the residue gases, the kinetic energy of species was reduced and the transport of depositing species changed from a ballistic movement for low pressure to a diffuse drift for high pressure in which the transport species were almost thermalized. The measurements show an increase of growth rates along the gravity vector when the Knodson (Knudsen??) number of transport species is less than 0.05, which suggests that gravity affected the transport characterization in off-axis sputtering deposition. Because the product of pressure (p) and travel distance (d) of sputtered species, p exceeds several mTorr-cm during film deposition, the classical simulations for sputtering process in high vacuum system may not be applied. Based on these experimental measurements, a transport process of the off-axis sputtering deposition is proposed. Several methods including the Monte Carlo method and gravity-driven flow dynamics simulation will be discussed.

Zhu, S.↗

NASA NTRS2001

Gravity Effects in Carbon Nanotube Growth by Thermal Chemical Vapor Deposition

Carbon nanotubes are synthesized using thermal chemical vapor deposition. The sizes of these carbon nanotubes (CNT) are quite uniform and the length of the tube is up to several tens of micrometers. With the substrate surface normal either along or against the gravity vector, different growth orientations of CNT are observed by scanning electron microscopy although the Raman spectra are similar for samples synthesized at different locations. These results suggest the gravitation effects in the growth of long and small diameter CNT.

Zhu, S.↗

NASA NTRS2001

Growth Orientation of Carbon Nanotubes by Thermal CVD

Carbon nanotubes with a few shells are synthesized using thermal chemical vapor depositions. The sizes of these carbon nanotubes (CNT) are quite uniform and the length is up to several tens of micrometers. With the particular substrate location for which the substrate surface is normal along or against the gravity vector, different growth orientations of CNT are observed by scanning electron microscopy, though the Raman spectra for samples at different locations are similar to each other. The results suggest the gravitation effects in growth of the long and small diameter CNT.

Zhu, S.↗

NASA NTRS2001

Carbon Nanotubes Growth by CVD in Various Conditions

Since the superior properties of multi-wall carbon nanotubes (MWCNT could be used in numerous devices such as electronics and sensors, many efforts have been engaged in synthesizing particular structural or dimensional MWCNT. This presentation will illustrate MWCNT synthesized on silicon substrates by thermal CVD. On the substrate, an array of catalysts is coated using sputtering deposition. A thin Ti buffer layer is also coated on some Si substrates prior to depositing catalyst particles. Nickel, cobalt or iron transition metals are used as catalysts for the MWCNT growth. Since the diameter of MWCNT depends on the size of catalyst particles, the catalyst particle size is investigated after annealed at various temperatures. MWCNT are grown on the substrate in the temperature range of 700 to 1000 C and the pressure range of 100 torr to one atmosphere. Methane and hydrogen gases with methane content of 10% to 100% are used for the MWCNT synthesis. Morphology, length and diameter of these MWCNT are determined by scanning electron microscopy and Raman spectroscopy. The detailed results of syntheses and characterizations will be discussed in the presentation.

Zhu, S.↗

NASA NTRS2000

The Preparation Conditions of Chromium Doped ZnSe and Their Effect on the Infrared Luminescence Properties

We report the investigation by photoluminescence lifetime measurements of the near-IR emissions from a series of chromium-doped ZnSe samples, correlated to their preparation conditions. The samples were polycrystalline or single crystals prepared by post growth diffusion doping or single crystals doped during growth by the physical vapor transport method. Room temperature lifetime values between 6 and 8 micro seconds were measured for samples with Cr2+ from low 10(exp 17) to high 10(exp 18) / cubic cm range. Lifetime data taken down to 78 K was found to be rather temperature independent, reconfirming previous reports indicating a quantum yield of the corresponding emission of close to 100% at room temperature. A strong decrease in the room temperature lifetime was found for chromium concentrations higher than 10(exp 19) / cubic CM.

Burger, A.↗

NASA NTRS1999

Effect of a Nonplanar Melt-Solid Interface On Lateral Compositional Distribution During Unidirectional Solidification of a Binary Alloy with a Constant Growth Velocity V: Theory - Pt. 1

Infrared detected materials, such as Hg(1-x)Cd(x)Te, Hg(1-x)Zn(x)Te have energy gaps almost linearly proportional to their composition. Due to the wide separation of liquidus and solidus curves of their phase diagram, there are compositional segregation in both of the axial and radial directions of these crystals grown in the Bridgman system unidirectionally with constant growth rate. It is important to understand the mechanisms, which affect lateral segregation such that large radially uniform composition crystal can be produced. Following Coriel, etc's treatment, we have developed a theory to study the effect of a curved melt-solid interface shape on lateral composition distribution. The model is considered to be a cylindrical system with azimuthal symmetry and a curved melt-solid interface shape which can be expressed as a linear combination of a series of Bessell's functions. The results show that melt-solid interface shape has a dominant effect on the lateral composition distribution of these systems. For small values of beta, the solute concentration at the melt-solid interface scales linearly with interface shape with a proportional constant of the produce of beta and (1 -k), where beta = VR/D, with V as growth velocity, R as the sample radius, D as the diffusion constant and k as the distribution constant. A detailed theory will be presented. A computer code has been developed and simulations have been performed and compared with experimental results. These will be published in another paper.

Wang, Jai-Ching↗