Search NASA⌕ Search

Engineering topics

Su, Jiann-Cherng

Publications and source records attributed to Su, Jiann-Cherng.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Electrofracturing of Shale at Elevated Pressure

Electrofracturing deeply buried shale formations could be used to increase reservoir permeability and improve reservoir production without requiring large volumes of freshwater. This paper describes a novel experimental system and initial test results to electrofracture shale under high confining pressures. Core-scale laboratory testing was performed on twelve rock samples recovered from a shale gas reservoir. Each sample was subjected to confining pressures of 20.7 MPa (3000 psi) or 58.6 MPa (8000 psi), representative of overburden pressures at depth. Samples were then subjected to application of high voltage until specimen fracture. The experiments produced deformed samples with multiple fracture types, both parallel and oblique to bedding planes. Electrofracturing increased permeabilities by up to nine orders of magnitude for extended time periods. Rock fracture and throughgoing fractures were demonstrated. Computed tomography images revealed the creation of fractures and tube/tunnel flow channels, which resisted closure under hydrostatic pressures up to 58.6 MPa. The breakdown energy and permeability changes in the sample were independent of applied confining pressure. The cumulative energy input required for fracture depended on applied confining pressure and sample length. The energy required to fracture samples up to 9 cm in length is generally more than 0.5 kJ/cm, but no greater than 1 kJ/cm. Our results show that electrofracture of shales under confining pressure is possible and could be a possible water-free mechanism for reservoir stimulation.

04 OIL SHALES AND TAR SANDS↗
DOE OSTI2023

Multilayer solid lubricant architecture for use in drilling tool applications

A coating architecture is disclosed that includes a substrate having a surface finish Ra of 0.3μ or finer, an intermediate layer overlying and in contact with the substrate; and a solid lubricant layer overlying and in contact with the intermediate layer. The test results of applying the coating architecture to a reciprocating hammer drill utilizing the coating is also disclosed.

Su, Jiann-Cherng↗
DOE OSTI2023

Downhole Sensing and Event-Driven Sensor Fusion for Depth-of-Cut Based Autonomous Fault Response and Drilling Optimization

Achieving robust and efficient drilling is a critical part of reducing the cost of geothermal energy exploration and extraction. Drilling performance is often evaluated using one or more of three key metrics: depth of cut (DOC), rate of penetration (ROP), and mechanical specific energy (MSE). All three of these quantities are related to each other. DOC refers to the depth a bit penetrates into rock during drilling. This is an important quantity for estimating bit behavior. ROP is the simply the DOC multiplied by the rotational rate, and represents how quickly the drill bit is advancing through the ground. ROP is often the parameter used for drilling control and optimization. Finally, MSE provides insight into drilling efficiency and rock type. MSE calculations rely on ROP, drilling force, and drilling torque. Surface-based sensors at the top of the drill are often used to measure all these quantities. However, top-hole measurements can deviate substantially from the behavior at the bit due to lag, vibrations, and friction. Therefore, relying only on top-hole information can lead to suboptimal drilling control. In this work, we describe recent progress towards estimating ROP, DOC, and MSE using down-hole sensing. We assume down-hole measurements of torque, weight-on-bit (WOB). Our hypothesis is that these measurements can provide more rapid and accurate measures of drilling performance. We show how a multi-layer perceptron (MLP) machine learning algorithm can provide rapid and accurate performance when evaluated on experimental data taken from Sandia’s Hard Rock Drilling Facility. In addition, we implement our algorithms on an embedded system intended to emulate a bottom-hole-assembly for sensing and estimation. Our experimental results show that DOC can be estimated accurately and in real-time. These estimates when combined with measurements for rotary speed, torque, and force can provide improved estimates for ROP and MSE. These results have the potential to enable better drilling assessment, improved control, and extended component lifetimes.

15 GEOTHERMAL ENERGY↗
DOE OSTI2023

Downhole to surface communications platform for drilling applications

A drilling assembly for downhole to surface communications is provided. The drilling assembly includes a series of pipe segments coupled in fluid communication between a slip ring assembly and an end pipe portion. The slip ring assembly is coupled in data and fluid communication with the pipe segments. A surface communications link is in data communication with the drilling assembly via the slip ring assembly. An end pipe portion is coupled with the drilling assembly that includes an electronics assembly with electronic components for transferring data to the slip ring assembly via the drilling assembly. A drill bit is operably coupled with the end pipe portion for drilling a borehole. Each pipe segment includes an outer conductor portion, a hollow inner conductor portion, and a dielectric portion for electrical isolation between the outer conductor portion and the inner conductor portion.

Su, Jiann-Cherng↗
DOE OSTI2023

Sandia and Ditch Witch Technology Commercialization Fund Integral Motor and Percussive Hammer

This report captures the results of development and testing of a integral downhole motor and percussive hammer used for drilling in near-surface hard rock formations. The work was funded through the DOE Office of Technology Transitions Technology Commercialization Fund. It was a collaboration between Sandia National Labs and The Charles Machine Works (aka Ditch Witch). In the collaboration, Sandia developed a pneumatic motor derived from an indexing tool used in other drilling applications, and Ditch Witch developed the bearing pack tied to the output shaft of the motor as well as the angled beacon housing used for directional control.

15 GEOTHERMAL ENERGY↗
DOE OSTI2023

Control systems and methods to enable autonomous drilling

A system or method for drilling includes autonomously controlling a rotary or percussive drilling process as it transitions through multiple materials with very different dynamics. The method determines a drilling medium based on real-time measurements and comparison to prior drilling data, and identifies the material type, drilling region, and approximately optimal setpoint based on data from at least one operating condition. The controller uses these setpoints initially to execute an optimal search to maximize performance by minimizing mechanical specific energy. Near-bit depth-of-cut estimations are performed using a machine learning prediction deployed in an embedded processor to provide high-speed ROP estimates. The sensing capability is coupled with a near-bit clutching mechanism to support drilling dysfunction mitigation.

Buerger, Stephen↗
DOE OSTI2023

Utah FORGE 3-2418: Wellbore Fracture Imaging Using Inflow Detection Measurements - Workshop Presentation

This is a presentation on the Wellbore Fracture Imaging Using Inflow Detection Measurements project by Stanford University, presented by Dr. Roland N. Horne. The project's objective was to make measurements in the Utah FORGE wells, both before and after fracturing experiments, to map the fractures and estimate their flow magnitude. The approach utilizes a ion-specific electrode that will measure chloride in the well. The idea is that water flowing into the well from the fractures will have a different concentration of chloride than the surrounding water. This presentation was featured in the Utah FORGE R&D Annual Workshop on September 8, 2023. The workshop provided a valuable opportunity to explore the progress made in each of the 17 Research and Development projects funded under Solicitation 2020-1 which aim to enhance our understanding of the crucial factors influencing the development of Enhanced Geothermal Systems (EGS) reservoirs and resources.

15 GEOTHERMAL ENERGY↗
DOE OSTI2023

A Technology Roadmap for Advanced Geothermal Well Construction

Recent analysis has shown that by 2050, geothermal energy can supply up to 90 GW of power to the U.S. electrical grid. Reducing the lifecycle cost of geothermal wells is critical to achieving this level of adoption. While time-related costs of drilling remain an important issue, there is also a need to focus on the costs associated with casing and cementing of geothermal wells. This report provides a roadmap of R&D activities needed to reduce the life cycle cost of casing and cementing while improving life-of-well performance. The purpose of the roadmap is to develop priorities for R&D in the areas of (1) high-performance and cost-effective materials for target geothermal well conditions, (2) well construction methods and techniques to reduce construction costs, and (3) methods and techniques to decrease to decrease long-term operating costs. The roadmap sets targets for the next 10-year period and purposely excludes R&D efforts into improved rock reduction. The roadmap was developed by a joint working group of experts from Oak Ridge National Laboratory, Brookhaven National Laboratory, and Sandia National Laboratories as well as 35 experts from industry and academia. Input from a series of information gathering sessions was used to inform and guide the development of the roadmap.

15 GEOTHERMAL ENERGY↗
DOE OSTI2023

Additive Manufacturing Case Study Test Report

Sandia National Labs collaborated with Oak Ridge National Laboratory on a case study examining additive manufacturing opportunities for Geothermal applications. The study focused on designing components with improved performance characteristics that cannot be fabricated conventionally. A rotor for a downhole motor was chosen based on the potential for improving its rotational dynamics. Topology optimization was used as a design method to reduce the rotational inertia of the part while preserving sufficient rotational stiffness to transmit the torque required for the drilling application. The optimization resulted in a nearly 50% reduction in polar moment of inertia while maintaining other desired performance characteristics. The design developed using the topology optimization approach was fabricated using additive manufacturing and cannot be fabricated conventionally.

15 GEOTHERMAL ENERGY↗