Search NASA⌕ Search

Engineering topics

Su, Yi-Feng

Publications and source records attributed to Su, Yi-Feng.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Corrosion evaluation of Al-Cu-Mn-Zr cast alloys in 3.5% NaCl solution

Corrosion behavior of cast Al-Cu-Mn-Zr (ACMZ) and RR350 alloys was compared to a cast 319 alloy in 3.5 wt.% NaCl. After 168 h immersion, ACMZ and RR350 alloys suffered from preferential attack adjacent to intermetallic particles decorated at grain boundaries while the attack in 319 occurred in eutectic Al-Si dendritic boundaries. Electrochemical data allowed semiquantitative comparison of alloy resistance to corrosion initiation, and ACMZ type alloys, including RR350 and three alloys with higher Cu, were considered more resistant than 319 due to the absence of deleterious Si particles. In case of 319, such Si particles presumably drove higher micro-galvanic influence to initiate and sustain Al corrosion. With lower susceptibility to corrosion initiation, ACMZ alloys should exhibit higher or at minimum similar resistance compared to cast 319.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Investigation of Chemical Species in the Corrosion Barrier Layer on Thermal CO 2 Treated AZ91D Magnesium Alloy with Lithium Nitrate

A unique corrosion barrier layer, formed by thermal CO 2 treatment with LiNO 3 on AZ91D, was characterized to reveal the chemical species and their spatial distribution using the combination of scanning transmission electron microscopy (STEM), energy dispersive spectroscopy (EDS), and electron energy loss spectroscopy (EELS) techniques. Two distinct and spatially segregated phases were identified as Li compound(s) with MgCO 3 and MgO in the surface barrier layer. Finally, based on the characterization results, it is presumed that the reaction of Mg oxide/hydroxide with LiNO 3 and CO 2 occurred preferentially in some local areas where Li compound(s) with MgCO 3 were present, but the unreacted areas contained MgO in the surface barrier layer.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Cost-Effective Thermomechanical Processing of Nanostructured Ferritic Alloys: Microstructure and Mechanical Properties Investigation

Nanostructured ferritic alloys (NFAs), such as oxide-dispersion strengthened (ODS) alloys, play a vital role in advanced fission and fusion reactors, offering superior properties when incorporating nanoparticles under irradiation. Despite their importance, the high cost of mass-producing NFAs through mechanical milling presents a challenge. This study delves into the microstructure-mechanical property correlations of three NFAs produced using a novel, cost-effective approach combining severe plastic deformation (SPD) with the continuous thermomechanical processing (CTMP) method. Analysis using scanning electron microscopy (SEM)-electron backscatter diffraction (EBSD) revealed nano-grain structures and phases, while scanning transmission electron microscopy (STEM)-energy dispersive X-ray spectroscopy (EDS) quantified the size and density of Ti-N, Y-O, and Cr-O fine particles. Atom probe tomography (APT) further confirmed the absence of finer Y-O particles and characterized the chemical composition of the particles, suggesting possible nitride dispersion strengthening. Correlation of microstructure and mechanical testing results revealed that CTMP alloys, despite having lower nanoparticle densities, exhibit strength and ductility comparable to mechanically milled ODS alloys, likely due to their fine grain structure. However, higher nanoparticle densities may be necessary to prevent cavity swelling under high-temperature irradiation and helium gas production. Further enhancements in uniform nanoparticle distribution and increased sink strength are recommended to mitigate cavity swelling, advancing their suitability for nuclear applications.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Strength stability at high temperatures for additively manufactured alumina forming austenitic alloy

Several fast-spectrum nuclear reactors designed to generate high power (~450 MWe) rely on forced convection of media such as supercritical CO 2 , sodium, or liquid lead to cool the nuclear core, operating at temperatures up to 600 °C. Cost-effective, high-strength Fe-based alumina forming austenitic (AFA) alloys are a promising candidate for the fabrication of critical nuclear components. This study investigated laser powder bed fusion (LPBF) processing of an AFA alloy composition optimized for improved creep resistance. Electron microscopy revealed an elongated grain structure along the build direction with a fine sub-grain cellular structure decorated with (Cr,Fe,Nb) 23 C 6 carbide precipitates at the intercellular boundaries. Finally, at temperatures of 20–900 °C, the LPBF alloy's superior tensile properties compared to its arc-melted counterpart and other advanced steels (e.g., SS316) were attributed to the distribution of nano-sized carbide precipitates, whereas the high ductility was attributed to the LPBF alloy's elongated grain structure.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Performance Restoration of Iron Electrodes by Polarity Reversal after Long-Term Surface Fouling in Wastewater Electrocoagulation

Iron electrocoagulation (Fe-EC) performance often declines with time, producing lower contaminant removal efficiencies and higher energy requirements due to formation of a fouling layer on the electrodes. Here, we investigate the formation of the fouling layer and the effectiveness of polarity reversal to restore the Fe-EC performance. A thin, porous iron oxide layer initially forms on the anode, thickening into a dense, over 150-μm thick crystalline layer after extended operation. This fouling layer restricts dissolution and diffusion of Fe ions into the bulk solution, thus increasing the anode potential required to maintain a desired electrical current and decreasing Faradaic efficiency. Polarity reversal applied when performance decline is observed effectively removes the fouling layer, thereby restoring Faradaic and contaminant removal efficiencies and decreasing energy consumption. Our findings suggest that gas generation at the cathode surface after polarity reversal causes removal of the fouling layer. This study enhances the current understanding of fouling-layer formation in Fe-EC and offers a practical approach, involving polarity reversal, to maintain electrode reactivity and optimal Fe-EC performance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Elucidating Polymer Binder Entanglement in Freestanding Sulfide Solid-State Electrolyte Membranes

This study advances the development of flexible, sheet-type sulfide solid-state electrolytes (SSEs) for use in all-solid-state batteries, emphasizing the important and previously insufficiently investigated role of polymer binder entanglement. Here, the molecular weight of polymer binders is pivotal in crafting robust, freestanding SSE films. Our research uncovers a dual impact: higher molecular weight binders bolster the structural integrity of SSE films but elevate grain boundary resistance and diminish critical current density, whereas lower molecular weight poly(isobutylene) films, despite their more uniform distribution, lack the essential strain hardening or strength for sustained active material contact. Crucially, full cells employing higher molecular weight binders demonstrate improved discharge capacity retention, contrasting sharply with the notable capacity degradation in lower molecular weight cells. Our findings not only deepen the comprehension of binder influences in solid-state batteries but also chart a course for refining all-solid-state battery technologies, a key stride for the future of energy storage solutions.

25 ENERGY STORAGE↗
DOE OSTI2024

Open-air plasma-assisted deposition of organosilicon coating for corrosion protection of AZ91D Mg alloy

As a corrosion barrier layer, open-air plasma-assisted organosilicon coating was applied on AZ91D Mg alloy. Organosilicon-coated AZ91D samples, prepared from two different plasma coating processes, were used for corrosion evaluation based on multistep electrochemical and H 2 collection measurements in 3.5 wt% sodium chloride (NaCl) solution. Some coated AZ91D samples were characterized with and without corrosion exposure in NaCl solution using electron microscopies and X-ray chemical analysis techniques. Further, the results indicate that the organosilicon coatings from open-air plasma processes are effective to delay the initiation of corrosion attack and also reduce the corrosion rate for AZ91D substrate. The corrosion attack was considered to develop after permeation of NaCl solution through the coating layer.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Leveraging Additive Manufacturing to Fabricate High Temperature Alloys With Co-Designed Mechanical Properties and Environmental Resistance

A paradigm shift in the traditional sequential design approaches is critically essential to create application-specific hierarchical and multifunctional materials with superior long-term performance for next-generation energy technologies involving extreme environments. In the current work, we aim to leverage the flexibility and geometric/compositional complexity offered by additive manufacturing to demonstrate this new approach by codesigning a compositionally graded Ni-based alloy for molten salts\sCO 2 heat exchangers to enable mitigation of environmental degradation of surfaces exposed to molten halide salts, while simultaneously suppressing the consequent deterioration in mechanical stability. Further, thermokinetic modeling describing the underlying physics of thermally- and environmentally induced spatiotemporal compositional and microstructural evolution will be employed to predict the parameter space of material deposition processes and precisely identify the required composition gradient. Preliminary corrosion and mechanical testing of the dual material demonstrated the potential of the material to replace existing solid solution strengthened materials for this application.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Multiscale characterization of an additively manufactured property graded Ni-base alloy for molten-salts\supercritical-CO 2 heat exchangers

The sequential optimization of strength and corrosion resistance in conventional alloy design procedures often results in a tradeoff between environmental degradation and optimal mechanical properties. A concurrent optimization of these two material properties is essential to efficiently develop high temperature alloys that can withstand harsh environments increasingly required for carbon–neutral energy technologies. In this work, we demonstrate the feasibility of directed energy deposition (DED) to manufacture a dual-corrosion resistant Ni-based alloy (Hastelloy N and Haynes 282), that meets the high temperature operation requirements of a molten-salts\supercritical-CO 2 (sCO 2 ) heat exchanger. A combination of multiscale characterization techniques and computational thermodynamics was employed to evaluate the cracking susceptibilities during fabrication and predict the microstructural stability of the material. Very good agreement was achieved between the observed and predicted phases and phase fractions of the as-printed material. A careful characterization of the transition zone between the two terminal alloy chemistries revealed potential precipitation strengthening (γ') on the Hastelloy N side while columnar-shaped M 23 C 6 and γ' precipitates that formed at grain boundaries (GBs) of the transition zone likely minimized the local interfacial energies. Both these mechanisms are believed to increase the interfacial stability but their performance at high temperatures requires further investigation.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Characterization and Electrochemical Analysis of Acidic Condensate-Induced Corrosion on Aluminized Coating on Steel in Residential Heaters

Condensing furnace residential heaters are starting to replace outdated and less efficient non-condensing units in homes across the US. However, the burning of natural gas in these new units produces acidic gases, which can form acid droplets (H 2 SO 4 , HNO 3 , H 2 CO 3 , etc.) that are corrosive to low-grade heat exchanger metallic materials. Type-1 aluminized steel has been used in industrial applications, such as marine, heating, and automobile parts, due to its resistance to oxidation at elevated temperature. Many components of the condensing furnaces, including heat exchangers, are made from type-1 aluminized steel. We investigated the interaction of type-1 aluminized steel substrates with two acidic condensate liquids by 500 h corrosion exposures as well as short-term electrochemical impedance measurements. SEM plan and cross-sectional view images revealed damage to the Al-Si rich layer and exposure of the steel substrate. The non-uniform damage in the Al-Si rich layer was likely attributed to a pitting corrosion mechanism and induced by high acidity of the condensate liquid. Electrochemical impedance measurements in an acidic condensate revealed lower corrosion resistance of the aluminized steel surface with a weld line, identifying welded sections as preferential corrosion initiation sites.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Evaluation of the interaction between SiC, pre-oxidized FeCrAlMo with aluminized and pre-oxidized Fe-8Cr-2W in flowing PbLi

We report dissimilar materials interactions are a major concern when liquid metals are used as a working fluid. To simulate a dual-coolant PbLi blanket, chemical vapor deposited (CVD) SiC, pre-oxidized FeCrAlMo (APMT) and pre-oxidized aluminized coating on Fe-8Cr-2 W (F82H) specimens were exposed to flowing commercial Pb-17at.%Li with a peak temperature of 650 °C in a pre-oxidized APMT thermal convection loop (TCL) for 1000 h. Similar to prior results in static PbLi, the coated F82H showed small mass changes and limited degradation of room-temperature tensile properties. After exposure, the α-Al 2 O 3 on the surface coated F82H reacted with the PbLi to form LiAlO 2 . However, no significant Al coating loss or interdiffusion was observed. Mass transfer was observed between the APMT, TCL and the SiC specimens. Fe, Cr and Ni were dissolved into the molten flowing PbLi and transported through the TCL to react with the SiC specimens. Compared to a prior experiment with a majority of bare FeCrAl specimens that were exposed in a TCL with a peak temperature of 700 °C for 1000 h, the SiC reaction was reduced to only a few microns of carbides and silicides. Oxygen dissolved in the molten PbLi sustained the formation of an Al 2 O 3 scale on the surface of the coating and induced the formation of a thin surface SiO 2 layer on the surface of the SiC.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Challenges in computationally designing high temperature Fe-based austenitic alloys: Addressing the role of Ni additions

Alumina-forming austenitic (AFA) alloys are relatively inexpensive high performance materials which combine the creep resistance of low-cost austenitic alloys and the oxidation resistance of expensive alumina forming alloys. However, a fundamental understanding of the role of key alloying elements such as Ni, Cr, Al, Nb, Ti, V, B and C in the experimentally observed oxidation behavior of these alloys is still lacking. The present work is a first in a series of studies aiming to quantitatively describe the role of Ni in promoting or disrupting protective Al 2 O 3 scale formation on AFA alloys. Here, ternary Fe-Al-xNi model alloys with three different Ni contents were isothermally exposed in an atmosphere with a low partial pressure of oxygen between 800–1000 °C for 24 h to evaluate the role of Ni in the observed internal oxidation behavior. Increasing Ni contents had no impact on the internal oxidation behavior of the alloys. The experimental and theoretical analyses in the present work suggested a negligible effect of the internal oxide precipitates on the inward diffusion of oxygen, typically expected in these systems, while simultaneously highlighting the barriers in the development of reliable models for computation-assisted design of these alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Effects of Cr/Zircaloy-4 coating qualities for enhanced accident tolerant fuel cladding

Cr-coated zirconium alloys represent a modern approach to enhance cladding safety during accident scenarios. Two high-power impulse magnetron sputtered Cr-coated Zry-4 systems were subjected to simulated loss-of-coolant accident conditions to investigate cladding performance. The first Cr-coating (4.8 µm thick) was deposited onto Zry-4 cladding and exhibited through-thickness cracking while the second Cr-coating (6.8 µm thick) was deposited with improved deposition parameters onto polished Zry-4 and exhibited no cracking. During burst testing, the coating with a higher density of defects failed to consistently reduce oxidation and exhibited similar burst behavior as Zry-4. In contrast, the second Cr-coating reduced ZrO 2 formation through formation of Cr 2 O 3 and displayed enhanced burst temperatures by ~80 °C compared to Zry-4. Utilizing an empirical relation for burst behavior of zirconium alloys, the 6.8 µm Cr/Zry-4 system displayed enhanced burst temperatures equivalent to an effective 0.464 mm increase in Zry-4 wall thickness, highlighting the value of continuous Cr coatings for accident scenarios.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2022

Corrosion Compatibility of Stainless Steels and Nickel in Pyrolysis Biomass-Derived Oil at Elevated Storage Temperatures

Corrosion compatibility of stainless steels and nickel (Ni200) was assessed in fast pyrolysis bio-oil produced from pyrolysis of high ash and high moisture forest residue biomass. Sample mass change, ICP-MS and post-exposure electron microscopy characterization was used to investigate the extent of corrosion. Among the tested samples, type 430F and type 316 stainless steels (SS430F and SS316) and Ni200 (~98.5% Ni) showed minimal mass changes (less than 2 mg∙cm−2) after the bio-oil exposures at 50 and 80 °C for up to 168 h. SS304 was also considered to be compatible in the bio-oil due to its relatively low mass change (1.6 mg∙cm−2 or lower). SS410 samples showed greater mass loss values even after exposures at a relatively low temperature of 35 °C. Fe/Cr values from ICP-MS data implied that Cr enrichment in stainless steels would result in a protective oxide layer associated with corrosion resistance against the bio-oil. Post exposure characterization showed continuous and uniform Cr distribution in the surface oxide layer of SS430F, which showed a minimal mass change, but no oxide layer on a SS430 sample, which exhibited a significant mass loss.

09 BIOMASS FUELS↗
DOE OSTI2022

Effect of Carboxylic Acids on Corrosion of Type 410 Stainless Steel in Pyrolysis Bio-Oil

Biomass-derived oils are renewable fuel sources and commodity products and are proposed to partially or entirely replace fossil fuels in sectors generally considered difficult to decarbonize such as aviation and maritime propulsion. Bio-oils contain a range of organic compounds with varying functional groups which can lead to polarity-driven phase separation and corrosion of containment materials during processing and storage. Polar compounds, such as organic acids and other oxygenates, are abundant in bio-oils and are considered corrosive to structural alloys, particularly to those with a low-Cr content. To study the corrosion effects of small carboxylic acids present in pyrolysis bio-oils, type 410 stainless steel (SS410) specimens were exposed in bio-oils with varying formic, acetic, propionic and hexanoic acid contents at 50 °C during 48 h exposures. The specific mass change data show a linear increase in mass loss with increasing formic acid concentration. Interestingly, a mild corrosion inhibition effect on the corrosion of SS410 specimens was observed with the addition of acetic, propionic and hexanoic acids in the bio-oil.

09 BIOMASS FUELS↗
DOE OSTI2022

Steam oxidation and microstructural evolution of rare earth silicate environmental barrier coatings

A primary failure mode for environmental barrier coatings (EBCs) on SiC ceramic matrix composites (CMCs) is the oxidation of the intermediate Si-bond coating, where the formation of SiO 2 at the bond coating–EBC interface results in debonding and spallation. This work compares the microstructure evolution and steam oxidation kinetics of the Si-bond coating beneath yttrium/ytterbium disilicate ((Y/Yb)DS) and ytterbium disilicate/monosilicate (YbDS/YbMS) EBCs to better understand the impact of EBC composition on oxidation kinetics. After 500 1-h cycles at 1350°C, (Y/Yb)DS displayed a decreasing concentration of the monosilicate minor phase and increasing concentration of porosity as furnace cycling time increased, whereas the YbDS/YbMS EBC displayed negligible microstructural evolution. For both EBC systems, thermally grown oxide growth rates in steam were found to increase by approximately an order magnitude compared to dry air oxidation. The (Y/Yb)DS EBC displayed a reduced steam oxidation rate compared to YbDS/YbMS.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Origin of the enhanced Nb3Sn performance by combined Hf and Ta doping

Abstract In recent years there has been an increasing effort in improving the performance of Nb 3 Sn for high-field applications, in particular for the fabrication of conductors suitable for the realization of the Future Circular Collider (FCC) at CERN. This challenging task has led to the investigation of new routes to advance the high-field pinning properties, the irreversibility and the upper critical fields ( H Irr and H c2 , respectively). The effect of hafnium addition to the standard Nb-4Ta alloy has been recently demonstrated to be particularly promising and, in this paper, we investigate the origins of the observed improvements of the superconducting properties. Electron microscopy, Extended X-ray Absorption Fine Structure Spectroscopy (EXAFS) and Atom Probe Tomography (APT) characterization clearly show that, in presence of oxygen, both fine Nb 3 Sn grains and HfO 2 nanoparticles form. Although EXAFS is unable to detect significant amounts of Hf in the A15 structure, APT does indeed reveal some residual intragrain metallic Hf. To investigate the layer properties in more detail, we created a microbridge from a thin lamella extracted by Focused Ion Beam (FIB) and measured the transport properties of Ta-Hf-doped Nb 3 Sn. H c2 (0) is enhanced to 30.8 T by the introduction of Hf, ~ 1 T higher than those of only Ta-doped Nb 3 Sn, and, even more importantly the position of the pinning force maximum exceeds 6 T, against the typical ~ 4.5–4.7 T of the only Ta-doped material. These results show that the improvements generated by Hf addition can significantly enhance the high-field performance, bringing Nb 3 Sn closer to the requirements necessary for FCC realization.

36 MATERIALS SCIENCE↗