Engineering topics

Subramanian, Srinath

Publications and source records attributed to Subramanian, Srinath.

9 records

DOE OSTI2024

Investigating the potential of a higher reactivity fuel to achieve faster heat-up of aftertreatment systems

Shortening the aftertreatment system heat-up period will be crucial to meet upcoming emissions regulations, which mandate significant reductions in tail-pipe emissions for on-road heavy-duty vehicles. This work studies the impact of increasing fuel reactivity on the combustion of post injections during the expansion stroke. The work demonstrates an operating strategy using a blend of di-butyl ether (a potential low-carbon biofuel component) and #2 diesel that achieves higher exhaust enthalpy, while maintaining similar engine-out emissions (NOx and combustion efficiency) in comparison to the baseline #2 diesel fuel (cetane number 41). On average, a 12% increase in exhaust enthalpy was observed for the blend (cetane number 60) relative to the baseline fuel. The ability to operate the higher reactivity fuel at a more retarded post-injection timing, where combustion with #2 diesel was found to be more unstable, and less complete was key to achieving higher exhaust enthalpy. However, a small fuel penalty (3%–5%) was also associated with the higher reactivity fuel with this operating strategy. The formation of fuel lean regions, due to the long ignition delays at late injection conditions, was predicted to be the leading contributor to the increased emissions of products of partial combustion. Here, chemical kinetic simulations using surrogates for the fuels used in the experiments, demonstrated the ability of a higher cetane fuel to outperform the baseline fuel under fuel lean conditions with equivalence ratios less than 0.7.

09 BIOMASS FUELS↗

DOE OSTI2024

Mono-Ether and Alcohol Bioblendstocks to Reduce the Fuel Penalty of Mixing Controlled Compression Ignition (MCCI) Engine Aftertreatment

An integrated approach utilizing catalysis experiments, process systems engineering, fuel property modeling, and engine testing was utilized in this project to optimize the production process and composition of a #2 diesel bioblendstock produced from ethanol consisting primarily of long-chain mono-ethers. The primary objective of the project was to determine the composition and to design the production process for a bioblendstock for #2 diesel fuel with > 50% reduction in greenhouse gas emissions relative to conventional diesel fuel. The desired bioblendstock needed to be blendable with #2 diesel fuel at > 5 vol. % while still meeting ASTM D975 diesel fuel specification properties and achieving improvements in fuel properties: increased cetane number, decreased sooting, and reduced pour point and cloud point temperatures. At the same time, it needed to reduce the fuel energy penalty associated with MCCI engine aftertreatment resulting in improved system efficiency. The findings of the current project demonstrate that primary objective of the work has been met, i.e., to determine the composition and to design the production process for a bioblendstock for #2 diesel fuel with > 50% reduction in greenhouse gas emissions relative to conventional diesel fuel. Additionally, the results indicate that the property objectives (increased cetane number, reduced pour and cloud points, and reduced sooting propensity) for the designed bioblendstock composition have also been met. Engine testing performed has also confirmed that the increased reactivity of the bioblendstock can be used to improve catalyst heating operation and to reduce the fuel penalty associated with this operation mode. The fuel property results demonstrate that >5 vol.% blending is easily achieved while meeting the ASTM D975 #2 diesel fuel property specifications tested in this work, as this was achieved for a blend with 43 vol. % of the bioblendstock. The results provide a foundation for future work to scaleup the catalytic production process designed in this work, with many of the challenges and areas for improvement being identified in this work to enable economic production with low GHG lifecycle emissions.

09 BIOMASS FUELS↗

DOE OSTI2023

Catalytic upgrading of ethanol to C8+ distillate range ethers via Guerbet coupling and etherification

In this presentation we describe the catalytic approaches for conversion of ethanol into diesel fuel ethers. This involves first alcohol oligomerization, followed by acid-catalyzed dehydration. As we will show in this presentation, ethanol can be converted to higher linear and α-branched alcohols by C-C coupling reactions (ethanol oligomerization) as well as to high molecular weight esters by C-O coupling reactions with Cu/MgxAlOy (CuHT) catalysts. Alcohols may be converted to ethers via bimolecular dehydration in a subsequent step. We have identified more than 160 number of species in the products including alcohols, esters, aldehydes, ketones, and olefins. Alcohols range from C4 to C10. Both alcohols and esters follow a Schulz-Flory chain growth model. We show the relationship between the catalyst properties (BET surface area, acid and base site count and Cu loading and synthesis method) and the performance in the reactions. We also show that physical mixtures of CuHT and HT can have similar product selectivity of low loading CuHT catalysts. The selectivity towards diesel fuel precursor compounds (hereafter ‘DFPC’) increased with conversion until reaching a plateau at high ethanol conversion (~70%). Alcohol selectivity follows a Schultz-Flory distribution at all studied conversions, and that adsorbed ethanol-derived species may undergo surface oligomerization into 1-butanol and higher alcohols before desorbing in a chain-growth mechanism. Zeolite catalysts convert the C4+ alcohols into C8+ ethers in both batch and continuous flow reactors. Selectivities of up to 80% to C8+ ethers at around 70% conversion using a single pass continuous flow system are achieved. The final product feedstocks obtained from etherification have been used in technoeconomic (TEA) and lifecycle analysis (LCA), which indicate a reduction in greenhouse gas (GHG) emissions of 50% relative to conventional diesel and diesel fuel prices that are lower than biodiesel. These final feedstocks are undergoing engine testing to elucidate the physiochemical properties and compare well to diesel #2 ASTM standards.

Huber, George↗

DOE OSTI2023

Production of bio-diesel blend stocks via acid-catalyzed dehydration of ethanol oligomerization products

Ethanol is the most widely produced biofuel in the world. Gasoline demand is projected to decrease in the next 20 years largely due to an increase in electric vehicles. Diesel fuel demand is projected to continue to increase. Long-chain mono C10+ ethers have high cetane numbers and appropriate physical properties to be blended at high levels into petroleum diesel fuel. A techno-economic analysis shows that the ethers can be produced at prices similar to biodiesel. In our presentation we will show the catalytic chemistry involved in our ethanol to diesel approach, the engine and physical measurements of the produced diesel-range ethers, and a summary of the techno-economic analysis.

Canales, Emmanuel↗

DOE OSTI2023

Exploration of Fuel Property Impacts on the Combustion of Late Post Injections Using Binary Blends and High-Reactivity Ether Bioblendstocks

In this study, the impacts of fuel volatility and reactivity on com- bustion stability and emissions were studied in a light-duty single- cylinder research engine for a three-injection catalyst heating oper- ation strategy with late post-injections. N-heptane and blends of farnesane/2,2,4,4,6,8,8-heptamethylnonane were used to study the im- pacts of volatility and reactivity. The effect of increased chemical reac- tivity was also analysed by comparing the baseline #2 diesel operation with a pure blend of mono-ether components (CN > 100) representa- tive of potential high cetane oxygenated bioblendstocks and a 25 vol.% blend of the mono-ether blend and #2 diesel with a cetane number (CN) of 55. At constant reactivity, little to no variation in combustion performance was observed due to differences in volatility, whereas in- creased reactivity improved combustion stability and efficiency at late injection timings. Fuels with higher reactivity were found to reduce engine-out hydrocarbon and carbon monoxide emissions while also achieving stable combustion at post-injection timings later than those achievable with #2 diesel fuel. The pure ether blend had the latest achievable post-injection timing of +30.5 CAD while still maintaining stable combustion (coefficient of variation of gross-indicated mean ef- fective pressure < 5%). With post-injection timing adjusted to achieve a matched exhaust temperature of 300 °C, the ether-diesel CN 55 blend was observed to have slightly higher thermal efficiency in comparison to the baseline #2 diesel fuel. The results also indicate that cetane num- ber may serve as a good indicator of combustion characteristics at late injection timings used for aftertreatment thermal management opera- tion.

99 GENERAL AND MISCELLANEOUS↗

DOE OSTI2023

Exploration of Fuel Property Impacts on the Combustion of Late Post Injections Using Binary Blends and High-Reactivity Ether Bioblendstocks

In this study, the impacts of fuel volatility and reactivity on combustion stability and emissions were studied in a light-duty single-cylinder research engine for a three-injection catalyst heating operation strategy with late post-injections. Here, N-heptane and blends of farnesane/2,2,4,4,6,8,8-heptamethylnonane were used to study the impacts of volatility and reactivity. The effect of increased chemical reactivity was also analysed by comparing the baseline #2 diesel operation with a pure blend of mono-ether components (CN > 100) representative of potential high cetane oxygenated bioblendstocks and a 25 vol.% blend of the mono-ether blend and #2 diesel with a cetane number (CN) of 55. At constant reactivity, little to no variation in combustion performance was observed due to differences in volatility, whereas increased reactivity improved combustion stability and efficiency at late injection timings. Fuels with higher reactivity were found to reduce engine-out hydrocarbon and carbon monoxide emissions while also achieving stable combustion at post-injection timings later than those achievable with #2 diesel fuel. The pure ether blend had the latest achievable post-injection timing of +30.5 CAD while still maintaining stable combustion (coefficient of variation of gross-indicated mean effective pressure < 5%). With post-injection timing adjusted to achieve a matched exhaust temperature of 300 °C, the ether-diesel CN 55 blend was observed to have slightly higher thermal efficiency in comparison to the baseline #2 diesel fuel. The results also indicate that cetane number may serve as a good indicator of combustion characteristics at late injection timings used for aftertreatment thermal management operation.

09 BIOMASS FUELS↗

DOE OSTI2022

Catalytic Upgrading of Ethanol to C8+ Distillate Range Ethers via Guerbet Coupling and Etherification

Guerbet coupling followed by etherification is a two step process for conversion of ethanol into distillate range molecules. This involves first alcohol oligomerization, followed by acid-catalyzed dehydration. As we will show in this presentation, ethanol can be converted to higher linear and α-branched alcohols by C-C coupling reactions (ethanol oligomerization) as well as to high molecular weight esters by C-O coupling reactions with Cu/MgxAlOy (CuHT) catalysts. Alcohols may be converted to ethers via bimolecular dehydration in a subsequent step. We have identified more than 160 number of species in the products including alcohols, esters, aldehydes, ketonces, and olefins. Alcohols range from C4 to C10. Both alcohols and esters follow a Schulz-Flory chain growth model. We show the relationship between the catalyst properties (BET surface area, acid and base site count and Cu loading and synthesis method) and the performance in the reactions. We also show that physical mixtures of CuHT and HT can have similar product selectivity of low loading CuHT catalysts. The selectivity towards diesel fuel precursor compounds (hereafter ‘DFPC’) increased with conversion until reaching a plateau at high ethanol conversion (~70%). Alcohol selectivity follows a Schultz-Flory distribution at all studied conversions, and that adsorbed ethanol-derived species may undergo surface oligomerization into 1-butanol and higher alcohols before desorbing in a chain-growth mechanism. Zeolite catalysts convert the C4+ alcohols into C8+ ethers in both batch and continuous flow reactors. Selectivities of up to 80% to C8+ ethers at around 70% conversion using a single pass continuous flow system are able to be achieved. The final product feedstocks obtained from etherification have been used in technoeconomic (TEA) and lifecycle analysis (LCA), which indicate a reduction in greenhouse gas (GHG) emissions of 50% relative to conventional diesel. These final feedstocks are undergoing engine testing to elucidate the physiochemical properties and will be compared to diesel #2 ASTM standards as a reference and will serve as a basis to improve the final bio-diesel blendstocks from etherification.

Huber, George↗

DOE OSTI2022

Impact of Fuel Properties on the Combustion of Late Post Injections used for Aftertreatment Thermal Management

Typical calibration for catalyst thermal management for compression-ignition engines involves delaying the post-injection into the expansion stroke. Reduced work extraction due to the late heat release event is used to increase the exhaust gas temperature to shorten the time associated with reaching optimal temperatures for aftertreatment systems. Shorter catalyst heat-up time can simultaneously reduce tail-pipe emissions and the typical fuel penalties associated with this mode of operation. In this study, the effects of volatility, reactivity, and oxygen content of the fuel on combustion stability and emissions were studied in a light-duty single-cylinder research engine. Blends of iso-octane/ n-heptane and farnesane/ 2,2,4,4,6,8,8-heptamethylnonane were used to study the impacts of volatility and reactivity. At constant reactivity, little to no variation in combustion performance was observed due to differences in volatility. On the other hand, increased reactivity improved combustion stability and efficiency at late injection timings (+24 CAD). The combined effect of increase in chemical reactivity and oxygen content was analysed by comparing the baseline #2 diesel operation with two blends of mono-ethers and #2 diesel to achieve cetane numbers (CNs) of 45 and 55, and a pure blend of mono-ether components with CN > 100. Fuels with higher reactivity and oxygen content were found to reduce engine-out hydrocarbon and carbon mono-oxide emissions while also achieving stable combustion at post-injection timings later than those achievable with diesel fuel. The pure ether-blend had the latest achievable post-injection timing (≥+26 CAD) while still maintaining stable combustion. At similar combustion stability, the pure ether blend was found to have 2.8% higher combustion efficiency and 4.3% higher thermal efficiency than the baseline diesel. The ether-diesel blends at CN45 and CN55 were found to have 1.8% higher combustion efficiency than baseline diesel. The results demonstrate that fuels with increased reactivity can increase combustion efficiency, reducing carbon monoxide and hydrocarbon emissions, while maintaining similar exhaust temperature and combustion stability compared to baseline diesel. Further greenhouse gas benefits can also be realized as the mono-ether bioblendstocks show potential for >50% reduction in greenhouse gas emissions relative to diesel fuel based on their production method.

99 GENERAL AND MISCELLANEOUS↗

DOE OSTI2020

Optical Investigation of Catalyst Heating Operation in a Light-Duty Compression-Ignition Engine

It is well known that cold start engine operation contributes a majority of tail-pipe emissions during a vehicle drive cycle. Aftertreatment catalysts have poor conversion efficiency during this period due to low conversion efficiency at temperatures less than their light-off temperature. A late post injection strategy, with a delayed injection to increase exhaust enthalpy, can help decrease the time required to heat-up the catalyst. However, late injections into conditions with decreasing temperature and density can result in high emissions and combustion instability. In this study a three-injection strategy with a late-post injection was investigated in an optically-accessible engine. For the first two injections (pilot and main) timing and duration were held constant as the post injection timing was swept and duration varied to hold load constant, at a relevant light-load catalyst heating operating condition. Simultaneous double-pass schlieren and OH chemiluminescence data were acquired in an optically-accessible 0.4 L single-cylinder engine to understand spray characteristics and combustion behavior for #2 diesel fuel. Optical images analysis revealed higher liquid penetration and lower vaporization of the liquid fuel jet as post injection is retarded. It is also observed that retarding post injection timing to +25 CAD resulted in lower observed soot concentration in the piston bowl.

99 GENERAL AND MISCELLANEOUS↗