Search NASA⌕ Search

Engineering topics

Suetsugu, Y.

Publications and source records attributed to Suetsugu, Y..

First measurements of beam backgrounds at SuperKEKB

The high design luminosity of the SuperKEKB electron-positron collider is expected to result in challenging levels of beam-induced backgrounds in the interaction region. Properly simulating and mitigating these backgrounds is critical to the success of the Belle~II experiment. We report on measurements performed with a suite of dedicated beam background detectors, collectively known as BEAST II, during the so-called Phase 1 commissioning run of SuperKEKB in 2016, which involved operation of both the high energy ring (HER) of 7 GeV electrons as well as the low energy ring (LER) of 4 GeV positrons. We describe the BEAST II detector systems, the simulation of beam backgrounds, and the measurements performed. The measurements include standard ones of dose rates versus accelerator conditions, and more novel investigations, such as bunch-by-bunch measurements of injection backgrounds and measurements sensitive to the energy spectrum and angular distribution of fast neutrons. We observe beam-gas, Touschek, beam-dust, and injection backgrounds. We do not observe significant synchrotron radiation, as expected. Measured LER beam-gas backgrounds and Touschek backgrounds in both rings are slightly elevated, on average three times larger than the levels predicted by simulation. HER beam-gas backgrounds are on on average two orders of magnitude larger than predicted. Systematic uncertainties and channel-to-channel variations are large, so that these excesses constitute only 1-2 sigma level effects. Neutron background rates are higher than predicted and should be studied further. We will measure the remaining beam background processes, due to colliding beams, in the imminent commissioning Phase 2. These backgrounds are expected to be the most critical for Belle II, to the point of necessitating replacement of detector components during the Phase 3 (full-luminosity) operation of SuperKEB

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Recommendation for Mitigations of the Electron Cloud Instability in the ILC

Electron cloud has been identified as one of the highest priority issues for the international Linear Collider (ILC) Damping Rings (DR). An electron cloud Working Group (WG) has evaluated the electron cloud effect and instability, and mitigation solutions for the electron cloud formation. Working group deliverables include recommendations for the baseline and alternate solutions to the electron cloud formation in various regions of the ILC Positron DR, which is presently assumed to be the 3.2 km design. Detailed studies of a range of mitigation options including coatings, clearing electrodes, grooves and novel concepts, were carried out over the previous several years by nearly 50 researchers, and the results of the studies form the basis for the recommendation. The recommendations are the result of the working group discussions held at numerous meetings and during a dedicated workshop. In addition, a number of items requiring further investigation were identified during the discussions at the Cornell meeting and studies will be carried out at CesrTA, a test accelerator dedicated to electron cloud studies, and other institutions.

43 PARTICLE ACCELERATORS↗

CesrTA Retarding Field Analyzer Measurements in Drifts, Dipoles, Quadrupoles and Wigglers

Over the course of the CesrTA program, the Cornell Electron Storage Ring (CESR) has been instrumented with several retarding field analyzers (RFAs), which measure the local density and energy distribution of the electron cloud. These RFAs have been installed in drifts, dipoles, quadrupoles, and wigglers; and data have been taken in a variety of beam conditions and bunch configurations. This paper will provide an overview of these results, and give a preliminary evaluation of the efficacy of cloud mitigation techniques implemented in the instrumented vacuum chambers.

43 PARTICLE ACCELERATORS↗

Experimental Studies on Grooved Surfaces to Suppress Secondary Electron Emission

Grooved surfaces are effective to suppress the secondary electron emission, and can be a promising technique to mitigate the electron cloud effect in positron/proton storage rings. Aiming for the application in a dipole-type magnetic field, various shapes of triangular grooved surfaces have been studied at KEK. The grooves tested here have vertex angles of 20-30{sup o}, depths of 2.5-5.0 mm, and vertex roundness of 0.05-0.2 mm. In a laboratory, the secondary electron yields (SEY) of small test pieces were measured using an electron beam in a magnetic-free condition. The grooved surfaces clearly had low SEY compared to flat surfaces of the same materials. The grooves with sharper vertexes had smaller SEY. A test chamber installed in a wiggler magnet of the KEKB positron ring was used to investigate the efficacy of the grooved surface in a strong magnetic field. In the chamber, a remarkable reduction in the electron density around the beam orbit was observed compared to the case of a flat surface with TiN coating.

43 PARTICLE ACCELERATORS↗

Beam Tests of a Clearing Electrode for Electron Cloud Mitigation at KEKB Positron Ring

In order to mitigate the electron cloud instability in an intense positron ring, an electron clearing electrode with a very thin structure has been developed. The electrode was tested with a positron beam of the KEKB B-factory (KEKB). A drastic reduction in the electron density around the beam was demonstrated in a wiggler magnet with a dipole-type magnetic field of 0.78 T. The clearing electrode was then applied to a copper beam pipe with antechambers assuming an application of the electrode to a wiggler section in the Super KEKB. The beam pipe was installed at a magnetic-free region in the ring and tested with beam. No extra heating of the electrodes and feed-throughs were observed. A reduction in the electron density reasonable in a magnetic-free region was also obtained.

43 PARTICLE ACCELERATORS↗

Recommendation for the Feasibility of more Compact LC Damping Rings

As part of the international Linear Collider (ILC) collaboration, we have compared the electron cloud (EC) effect for different Damping Ring (DR) designs respectively with 6.4 km and 3.2 km circumference and investigated the feasibility of the shorter damping ring with respect to the electron cloud build-up and related beam instabilities. The studies for a 3.2 km ring were carried out with beam parameters of the ILC Low Power option. A reduced damping ring circumference has been proposed for the new ILC baseline design SB2009 [1] and would allow considerable reduction of the number of components, wiggler magnets and costs. We discuss the impact of the proposed operation of the ILC at high repetition rate 10 Hz and address the necessary modifications for the DRs. We also briefly discuss the plans for future studies including the luminosity upgrade option with shorter bunch spacing, the evaluation of mitigation techniques and the integration of the CesrTA results into the Damping Ring design.

43 PARTICLE ACCELERATORS↗