Search NASA⌕ Search

Engineering topics

Sui, Yongkun

Publications and source records attributed to Sui, Yongkun.

9 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

The Influence of Microstructure on TCR for Inkjet-Printed Resistive Temperature Detectors Fabricated Using AgNO 3 /Ethylene-Glycol-Based Inks

This study investigated the influence of microstructure on the performance of Ag inkjet-printed, resistive temperature detectors (RTDs) fabricated using particle-free inks based on a silver nitrate (AgNO 3 ) precursor and ethylene glycol as the ink solvent. Specifically, the temperature coefficient of resistance (TCR) and sensitivity for sensors printed using inks that use monoethylene glycol (mono-EG), diethylene glycol (di-EG), and triethylene glycol (tri-EG) and subjected to a low-pressure argon (Ar) plasma after printing were investigated. Scanning electron microscopy (SEM) confirmed previous findings that microstructure is strongly influenced by the ink solvent, with mono-EG inks producing dense structures, while di- and tri-EG inks produce porous structures, with tri-EG inks yielding the most porous structures. RTD testing revealed that sensors printed using mono-EG ink exhibited the highest TCR (1.7 × 10 -3 /°C), followed by di-EG ink (8.2 × 10 -4 /°C) and tri-EG ink (7.2 × 10 -4 /°C). These findings indicate that porosity exhibits a strong negative influence on TCR. Sensitivity was not strongly influenced by microstructure but rather by the resistance of RTD. The highest sensitivity (0.84 Ω/°C) was observed for an RTD printed using mono-EG ink but not under plasma exposure conditions that yield the highest TCR.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

An Aerosol Jet Printed Resistance Temperature Detector‐Micro Hotplate with Temperature Coefficient of Resistance Stabilized by Electrical Sintering

Abstract Aerosol jet printing (AJP) is an emerging direct write tool enabling rapid prototyping and fabrication of electronics components. AJP provides faster and less expensive production of devices with feature sizes of >10 microns compared to traditional MEMS processes. Herein, the fabrication of a resistance temperature detector‐micro hotplate (RTD‐µHP) is reported using AJP printed silver. AJP eliminates sophisticated MEMS processes such as masking, alignment, and etching. The compatibility of the AJP process with a broad range of materials is demonstrated by printing highly resolved lines on rigid and flexible substrates. Optimal thermal sintering conditions of AJP printed silver (Ag) lines are found by in situ resistance measurements. To stabilize the temperature coefficient of resistance (TCR) of the RTD‐µHP at high operating current levels, electrical sintering is performed on the RTD‐µHPs. Electrical sintering improves the conductivity of fully thermally sintered Ag RTD‐µHPs by 32% and provides a burn‐in mechanism for stabilizing the TCR. The TCR of the RTD‐µHPs after electrical sintering is 3.80 × 10 −3 at 22 °C, close to the value for bulk Ag. The performance of the RTD‐µHPs is tested using a reference thermocouple. The RTD‐µHPs show reliable and repeatable heating and temperature sensing up to 70 °C in air.

Sui, Yongkun↗
DOE OSTI2022

A Reactive Inkjet Printing Process for Fabricating Biodegradable Conductive Zinc Structures

A novel reactive inkjet printing (RIJ) process for fabricating environmentally benign, conductive zinc structures on biodegradable substrates is reported. A precursor consisting of oxidized zinc microparticles is formulated into a viscous ink for high‐resolution, high‐repeatability screen printing. A single RIJ process is performed to selectively dispense an acid‐based oxide etching agent onto the screen‐printed zinc ink to significantly improve its electrical conductivity, up to 4 × 10 4 S m −1 . The RIJ process enables precise control of the amount of deposited etching agent, allowing control of conductivity and avoiding damage caused by excessive acid exposure. The RIJ process deposits the etching agent selectively on the screen‐printed, water‐soluble zinc patterns, thus preserving the print fidelity by avoiding ink smearing that can occur when using a blanket treatment such as submersion. A printed biodegradable antenna with a minimum feature size of 500 μm for use with a batteryless radio frequency identification (RFID) chip is fabricated as demonstration. Due to the higher ink conductivity and improved pattern fidelity, the antenna fabricated by the RIJ process shows a ≈2.2× increase in reading distance compared with a similar antenna that is screen printed and activated using a drop‐casting process.

Sui, Yongkun↗